Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2014.12–2015.11
RM2170E _57 Power Source / Network _057033 NETWORKING _0278068 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Center Airbag Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Center Airbag Sensor Communication Stop Mode Either condition is met:
·

"Airbag" is not displayed on the "Communication Bus Check" screen of the intelligent tester (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Center Airbag Sensor Communication Stop Mode" in "DTC Combination Table" (See page (Click here))


·

Airbag sensor assembly branch line or connector

·

Power source circuit of airbag sensor assembly

·

Airbag sensor assembly ground circuit

·

Airbag sensor assembly



WIRING DIAGRAM

C252848E09
3.458,1.281 3.198,0.833 3.198,0.833 2.906,0.833 false 5.458,1.281 5.781,0.667 5.781,0.667 6.031,0.667 false 4.948,0.552 5.323,0.698 0.375,0.146 10 false DLC3 4.969,3.625 5.823,3.823 0.854,0.198 10 false Trouble Area 0.354,2.833 1.563,3.323 1.208,0.49 10 false Combination Meter Assembly 6.073,0.583 6.969,1.219 0.896,0.635 10 false CAN Junction Connector LH 2.74,4.25 4.313,4.417 1.573,0.167 10 false Airbag Sensor Assembly 1.813,3.802 2.552,4.083 0.74,0.281 10 false IG2 NO. 2 2.969,3.292 3.396,3.448 0.427,0.156 10 false CANH 3.51,3.292 3.906,3.448 0.396,0.156 10 false CANL 2.76,3.667 3,3.813 0.24,0.146 10 false IG2 3.938,3.542 4.135,3.698 0.198,0.156 10 false E1 3.938,3.854 4.135,4 0.198,0.146 10 false E2 3.052,3.083 3.219,3.24 0.167,0.156 10 false 13 3.688,3.073 3.854,3.219 0.167,0.146 10 false 22 6.26,2.208 6.656,2.385 0.396,0.177 10 false 120 Ω 0.708,2.198 1.104,2.375 0.396,0.177 10 false 120 Ω 1.125,5 3.042,5.323 1.917,0.323 10 false : CAN Main Bus Line (CANH) 1.125,5.406 3.042,5.729 1.917,0.323 10 false : CAN Main Bus Line (CANL) 4.26,5.031 6.01,5.354 1.75,0.323 10 false : CAN Branch Line (CANH) 4.26,5.406 5.969,5.729 1.708,0.323 10 false : CAN Branch Line (CANL) 2.531,3.563 2.708,3.719 0.177,0.156 10 false 21 4.177,3.469 4.344,3.615 0.167,0.146 10 false 25 4.188,3.75 4.354,3.906 0.167,0.156 10 false 26 1.094,0.75 3.073,1.083 1.979,0.333 10 false CAN Junction Connector RH 2.427,4.26 2.719,4.417 0.292,0.156 10 false G18 6.281,2.823 6.635,3.021 0.354,0.198 10 false ECM 0.125,0.083 1.458,0.354 1.333,0.271 12 false V Bus (for LHD):

C251623E11
5.313,1.271 5.646,0.656 5.646,0.656 5.896,0.656 false 2.833,1.281 3.156,0.667 3.156,0.667 3.406,0.667 false 2.042,0.552 2.417,0.698 0.375,0.146 10 false DLC3 4.979,3.854 5.833,4.052 0.854,0.198 10 false Trouble Area 0.333,2.844 1.542,3.333 1.208,0.49 10 false Combination Meter Assembly 6.073,0.552 6.969,1.188 0.896,0.635 10 false CAN Junction Connector LH 2.75,4.271 4.323,4.438 1.573,0.167 10 false Airbag Sensor Assembly 1.823,3.833 2.635,4.156 0.813,0.323 10 false IG2 NO. 2 2.99,3.271 3.417,3.427 0.427,0.156 10 false CANH 3.521,3.271 3.917,3.427 0.396,0.156 10 false CANL 2.771,3.646 3.01,3.792 0.24,0.146 10 false IG2 3.938,3.542 4.135,3.698 0.198,0.156 10 false E1 3.938,3.844 4.135,3.99 0.198,0.146 10 false E2 3.063,3.063 3.229,3.219 0.167,0.156 10 false 13 3.708,3.083 3.875,3.229 0.167,0.146 10 false 22 6.271,2.198 6.667,2.375 0.396,0.177 10 false 120 Ω 0.719,2.188 1.115,2.365 0.396,0.177 10 false 120 Ω 1.135,5.01 3.052,5.333 1.917,0.323 10 false : CAN Main Bus Line (CANH) 1.135,5.438 3.052,5.76 1.917,0.323 10 false : CAN Main Bus Line (CANL) 4.271,4.99 6.021,5.313 1.75,0.323 10 false : CAN Branch Line (CANH) 4.271,5.427 5.979,5.75 1.708,0.323 10 false : CAN Branch Line (CANL) 2.552,3.552 2.729,3.708 0.177,0.156 10 false 21 4.188,3.479 4.354,3.625 0.167,0.146 10 false 25 4.198,3.76 4.365,3.917 0.167,0.156 10 false 26 3.531,0.573 4.438,1.219 0.906,0.646 10 false CAN Junction Connector RH 2.448,4.281 2.74,4.438 0.292,0.156 10 false G18 6.333,2.823 6.688,3.021 0.354,0.198 10 false ECM 0.146,0.167 1.479,0.438 1.333,0.271 12 false V Bus (for RHD):

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (AIRBAG SENSOR ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U183510E01
0.168,0.151 2.525,0.494 2.357,0.343 10 *a 1.584,2.791 2.039,2.947 0.455,0.156 10 CANH 1.336,2.366 1.053,2.772 false 1.446,2.114 1.806,2.772 false 0.802,2.791 1.257,2.947 0.455,0.156 10 CANL 1.564,1.334 1.844,1.478 0.280,0.145 10 G18

Disconnect the airbag sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G18-13 (CANH) - G18-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Airbag Sensor Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (AIRBAG SENSOR ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U159327E01
0.168,0.175 2.525,0.519 2.357,0.343 10 *a 0.673,2.056 0.867,2.211 0.194,0.156 10 E1 2.589,2.01 2.783,2.166 0.194,0.156 10 E2 1.561,1.37 1.847,1.517 0.287,0.147 10 G18 1.661,2.29 0.903,2.139 false 1.781,2.285 2.57,2.084 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G18-25 (E1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
G26-26 (E2) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Airbag Sensor Assembly)

b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.
U159328E01
0.168,0.151 0.379,0.371 0.211,0.220 10 *a 1.232,2.359 0.814,2.516 false 0.514,2.435 0.762,2.591 0.248,0.156 10 IG2 1.555,1.324 1.836,1.464 0.281,0.139 10 G18

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G18-21 (IG2) - Body ground Power switch on (IG) 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)