Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2014.12–2015.11
RM2170E _57 Power Source / Network _057033 NETWORKING _0278068 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Certification ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Certification ECU Communication Stop Mode Either condition is met:
·

"Certification (Smart)" is not displayed on the CAN Bus Check screen of the GTS (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that correspond to "Certification ECU Communication Stop Mode" in "DTC Combination Table" are output (See page (Click here)).


·

Smart key ECU assembly (Certification ECU) branch line or connector

·

Power source circuit of smart key ECU assembly (certification ECU)

·

Smart key ECU assembly (Certification ECU) ground circuit

·

Smart key ECU assembly (Certification ECU)



WIRING DIAGRAM

C260978E18
4.948,1.292 5.5,0.667 false 1.833,0.927 2,1.281 false 2.104,0.594 2.5,0.75 0.396,0.156 10 false DLC3 1.25,3.802 2.104,4 0.854,0.198 10 false Trouble Area 0.729,2.865 1.083,3.063 0.354,0.198 10 false ECM 5.771,2.854 7.01,3.26 1.24,0.406 10 false Combination Meter Assembly 5.552,0.563 6.521,0.948 0.969,0.385 10 false CAN Junction Connector RH 6.156,2.229 6.552,2.406 0.396,0.177 10 false 120 Ω 0.646,2.208 1.042,2.365 0.396,0.156 10 false 120 Ω 1.115,5 3.031,5.323 1.917,0.323 10 false : CAN Main Bus Line (CANH) 1.115,5.417 3.031,5.74 1.917,0.323 10 false : CAN Main Bus Line (CANL) 4.281,5 6.063,5.323 1.781,0.323 10 false : CAN Branch Line (CANH) 4.271,5.417 5.969,5.74 1.698,0.323 10 false : CAN Branch Line (CANL) 2.635,4.375 5.635,4.604 3,0.229 10 false Smart Key ECU Assembly (Certification ECU) 3.615,3.26 4.042,3.417 0.427,0.156 10 false CANH 4.156,3.26 4.552,3.417 0.396,0.156 10 false CANL 3.406,3.948 3.594,4.104 0.188,0.156 10 false IG 3.375,3.479 3.646,3.635 0.271,0.156 10 false +B 4.604,3.573 4.781,3.729 0.177,0.156 10 false E 3.51,3.083 3.688,3.229 0.177,0.146 10 false 14 4.458,3.083 4.646,3.24 0.188,0.156 10 false 15 4.885,3.375 5.042,3.521 0.156,0.146 10 false 11 3.156,3.271 3.25,3.417 0.094,0.146 10 false 2 3.135,3.76 3.323,3.906 0.188,0.146 10 false 5 2.354,3.635 2.802,3.833 0.448,0.198 10 false AM2 2.292,4.115 2.948,4.281 0.656,0.167 10 false IG2 NO. 2 0.104,0.823 2.021,1.083 1.917,0.26 10 false CAN Junction Connector LH 3.031,3.948 3.313,4.094 0.281,0.146 10 false G79 3.042,3.469 3.323,3.615 0.281,0.146 10 false G77 3.729,3.083 4.01,3.229 0.281,0.146 10 false G79 4.135,3.073 4.417,3.219 0.281,0.146 10 false G79 4.823,3.563 5.104,3.708 0.281,0.146 10 false G77 0.073,0.135 3.469,0.375 3.396,0.24 12 false V Bus (for LHD):

C251626E17
1.406,0.677 1.625,0.677 1.625,0.677 1.938,1.271 false 3.229,1.281 3.521,0.688 3.521,0.688 3.802,0.688 false 2.052,0.573 2.448,0.729 0.396,0.156 10 false DLC3 1.094,3.76 1.948,3.958 0.854,0.198 10 false Trouble Area 6.354,2.802 6.708,3 0.354,0.198 10 false ECM 0.344,2.823 1.583,3.229 1.24,0.406 10 false Combination Meter Assembly 0.156,0.583 1.406,1.25 1.25,0.667 10 false CAN No. 1 Junction Connector 6.188,2.198 6.583,2.375 0.396,0.177 10 false 120 Ω 0.698,2.188 1.094,2.365 0.396,0.177 10 false 120 Ω 1.115,5 3.031,5.323 1.917,0.323 10 false : CAN Main Bus Line (CANH) 1.115,5.406 3.031,5.729 1.917,0.323 10 false : CAN Main Bus Line (CANL) 4.25,5 6.031,5.323 1.781,0.323 10 false : CAN Branch Line (CANH) 4.25,5.406 5.948,5.729 1.698,0.323 10 false : CAN Branch Line (CANL) 2.531,4.469 5.385,4.813 2.854,0.344 10 false Smart Key ECU Assembly (Certification ECU) 3.604,3.281 4.083,3.458 0.479,0.177 10 false CANH 4.167,3.292 4.625,3.469 0.458,0.177 10 false CANL 3.375,3.469 3.646,3.656 0.271,0.188 10 false +B 3.396,3.969 3.604,4.135 0.208,0.167 10 false IG 4.646,3.563 4.792,3.74 0.146,0.177 10 false E 3.667,2.896 3.865,3.063 0.198,0.167 10 false 14 4.302,2.906 4.51,3.083 0.208,0.177 10 false 15 4.885,3.365 5.073,3.531 0.188,0.167 10 false 11 3.146,3.271 3.281,3.438 0.135,0.167 10 false 2 3.135,3.76 3.26,3.917 0.125,0.156 10 false 5 2.354,3.625 2.833,3.865 0.479,0.24 10 false AM2 2.25,4.156 3.26,4.458 1.01,0.302 10 false ECU-IG2 NO. 2 3.885,0.594 5.875,0.823 1.99,0.229 10 false CAN Junction Connector LH 3.042,3.469 3.333,3.656 0.292,0.188 10 false G77 3.75,3.083 4,3.24 0.25,0.156 10 false G79 4.125,3.083 4.375,3.24 0.25,0.156 10 false G79 3.063,3.948 3.292,4.115 0.229,0.167 10 false G79 4.823,3.573 5.094,3.76 0.271,0.188 10 false G77 0.104,0.125 1.406,0.365 1.302,0.24 12 false V Bus (for RHD): 6.063,2.802 6.375,2.958 0.313,0.156 10 false A25

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more.

·

After the repair, perform CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (SMART KEY ECU ASSEMBLY (CERTIFICATION ECU) BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U183539E01
0.176,0.145 0.380,0.335 0.204,0.189 10 *a 0.721,0.66 1.166,0.850 0.445,0.190 10 CANL 1.859,0.662 2.304,0.852 0.445,0.190 10 CANH 1.292,0.748 1.501,0.748 1.501,0.748 1.501,1.718 false 1.781,0.748 1.597,0.748 1.597,0.748 1.597,1.716 false 1.622,0.274 2.106,0.432 0.483,0.158 10 G79

Disconnect the G79 smart key ECU assembly (certification ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G79-14 (CANH) - G79-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Smart Key ECU Assembly (Certification ECU))



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (SMART KEY ECU ASSEMBLY (CERTIFICATION ECU))

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the G77 smart key ECU assembly (certification ECU) connector.


b.
U183541E01
0.131,0.137 0.350,0.330 0.220,0.194 10 *a 0.658,0.854 0.881,1.029 0.223,0.175 10 +B 2.566,1.176 2.716,1.358 0.150,0.182 10 E 2.242,1.261 2.526,1.261 false 0.906,0.939 1.19,0.939 false 1.532,2.08 1.952,2.231 0.420,0.152 10 G79 1.547,0.264 1.974,0.421 0.427,0.157 10 G77 0.492,1.994 1.048,2.177 0.557,0.183 10 CANH 1.051,2.092 1.279,2.092 1.279,2.092 1.501,3.086 false 1.035,2.31 1.219,2.31 1.219,2.31 1.409,3.082 false 0.482,2.233 1.039,2.416 0.557,0.183 10 CANL 0.84,2.535 1.024,2.535 1.024,2.535 1.133,2.928 false 0.619,2.45 0.927,2.633 0.308,0.183 10 IG

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G77-11 (E) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Smart Key ECU Assembly (Certification ECU))


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G77-2 (+B) - Body ground Power switch off 11 to 14 V
G79-5 (IG) - Body ground Power switch on (IG) 11 to 14 V




OK

REPLACE SMART KEY ECU ASSEMBLY (CERTIFICATION ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)