Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2014.12–2015.11
RM2170E _57 Power Source / Network _057033 NETWORKING _0278068 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Air Conditioning Amplifier Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Air Conditioning Amplifier Communication Stop Mode Either condition is met:
·

"Air Conditioning Amplifier" is not displayed on the "Communication Bus Check" screen of the intelligent tester (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Air Conditioning Amplifier Communication Stop Mode" in "DTC Combination Table" (See page (Click here))


·

Air conditioning amplifier assembly branch line or connector

·

Power source circuit of air conditioning amplifier assembly

·

Air conditioning amplifier assembly ground circuit

·

Air conditioning amplifier assembly



WIRING DIAGRAM

C252849E13
5.385,1.281 5.75,0.646 5.75,0.646 6.063,0.646 false 3.625,1.281 3.146,0.802 3.146,0.802 2.844,0.802 false 0.323,2.844 1.542,3.229 1.219,0.385 10 false Combination Meter Assembly 1.125,5 3.021,5.323 1.896,0.323 10 false : CAN Main Bus Line (CANH) 4.26,5 5.958,5.323 1.698,0.323 10 false : CAN Branch Line (CANH) 4.26,5.406 6.01,5.729 1.75,0.323 10 false : CAN Branch Line (CANL) 1.125,5.417 3.021,5.74 1.896,0.323 10 false : CAN Main Bus Line (CANL) 2.427,4.25 4.667,4.448 2.24,0.198 10 false Air Conditioning Amplifier Assembly 2.76,3.385 3.01,3.542 0.25,0.156 10 false IG+ 2.948,3.281 3.354,3.427 0.406,0.146 10 false CANH 3.531,3.292 3.917,3.469 0.385,0.177 10 false CANL 3.781,3.542 4.125,3.688 0.344,0.146 10 false GND 1.865,3.521 2.365,3.688 0.5,0.167 10 false HTR-IG 2.594,3.292 2.708,3.438 0.115,0.146 10 false 1 4.177,3.458 4.354,3.615 0.177,0.156 10 false 14 3.052,3.083 3.219,3.229 0.167,0.146 10 false 11 3.688,3.073 3.865,3.24 0.177,0.167 10 false 12 4.948,0.542 5.323,0.719 0.375,0.177 10 false DLC3 6.104,0.563 6.979,1.198 0.875,0.635 10 false CAN Junction Connector LH 4.99,3.573 5.823,3.771 0.833,0.198 10 false Trouble Area 0.646,2.198 1.042,2.375 0.396,0.177 10 false 120 Ω 6.146,2.208 6.542,2.385 0.396,0.177 10 false 120 Ω 1.031,0.719 2.844,0.885 1.813,0.167 10 false CAN Junction Connector RH 2.115,4.25 3.323,4.708 1.208,0.458 10 false G34 6.188,2.833 6.552,2.979 0.365,0.146 10 false ECM 0.125,0.073 1.469,0.344 1.344,0.271 12 false V Bus (for LHD): 2.531,3.813 2.708,3.969 0.177,0.156 10 false 21 2.771,3.906 2.906,4.063 0.135,0.156 10 false B 1.698,4.031 2.74,4.292 1.042,0.26 10 false ECU-B NO. 2

C251625E06
5.365,1.281 5.729,0.646 5.729,0.646 6.052,0.646 false 3.031,1.271 3.396,0.635 3.396,0.635 3.708,0.635 false 0.323,2.875 1.542,3.26 1.219,0.385 10 false Combination Meter Assembly 1.115,5.031 3.01,5.354 1.896,0.323 10 false : CAN Main Bus Line (CANH) 4.25,5.01 5.948,5.333 1.698,0.323 10 false : CAN Branch Line (CANH) 4.26,5.406 6.01,5.729 1.75,0.323 10 false : CAN Branch Line (CANL) 1.115,5.417 3.01,5.74 1.896,0.323 10 false : CAN Main Bus Line (CANL) 2.406,4.292 4.646,4.49 2.24,0.198 10 false Air Conditioning Amplifier Assembly 2.75,3.396 3,3.552 0.25,0.156 10 false IG+ 3.021,3.313 3.427,3.458 0.406,0.146 10 false CANH 3.49,3.313 3.875,3.49 0.385,0.177 10 false CANL 3.771,3.594 4.115,3.74 0.344,0.146 10 false GND 1.875,3.531 2.375,3.698 0.5,0.167 10 false HTR-IG 2.583,3.115 2.698,3.26 0.115,0.146 10 false 1 4.167,3.448 4.344,3.604 0.177,0.156 10 false 14 3.052,3.083 3.219,3.229 0.167,0.146 10 false 11 3.656,3.083 3.833,3.25 0.177,0.167 10 false 12 2.083,0.583 2.458,0.76 0.375,0.177 10 false DLC3 6.094,0.573 6.969,1.208 0.875,0.635 10 false CAN Junction Connector LH 4.979,3.625 5.813,3.823 0.833,0.198 10 false Trouble Area 0.74,2.24 1.135,2.417 0.396,0.177 10 false 120 Ω 6.135,2.219 6.531,2.396 0.396,0.177 10 false 120 Ω 3.75,0.563 4.667,1.208 0.917,0.646 10 false CAN Junction Connector RH 2.104,4.302 2.396,4.448 0.292,0.146 10 false G34 6.177,2.823 6.542,2.969 0.365,0.146 10 false ECM 0.104,0.104 1.448,0.375 1.344,0.271 12 false V Bus (for RHD): 2.521,3.646 2.698,3.802 0.177,0.156 10 false 21 2.76,3.906 2.896,4.063 0.135,0.156 10 false B 1.875,4.063 2.917,4.344 1.042,0.281 10 false ECU-B NO. 2

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U159534E01
1.566,0.773 1.847,0.926 0.282,0.153 10 G34 0.097,0.094 0.255,0.246 0.158,0.152 10 *a 0.814,1.39 1.243,1.542 0.429,0.152 10 CANH 2.298,1.385 2.727,1.537 0.429,0.152 10 CANL 1.801,2.396 1.622,1.478 1.622,1.478 1.327,1.478 false 1.914,2.394 1.996,1.469 1.996,1.469 2.276,1.469 false

Disconnect the air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G34-11 (CANH) - G34-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U159535E01
1.566,0.773 1.847,0.926 0.282,0.153 10 G34 0.097,0.094 0.255,0.246 0.158,0.152 10 *a 2.743,1.682 3.070,1.833 0.327,0.152 10 GND 2.145,2.381 2.424,1.767 2.424,1.767 2.705,1.767 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G34-14 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)

b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.
U183608E02
0.635,2.385 0.688,1.552 0.688,1.552 0.917,1.552 false 0.635,2.635 0.635,3.021 0.635,3.021 0.781,3.021 false 1.604,0.781 1.885,0.938 0.281,0.156 10 false G34 0.125,0.094 0.281,0.25 0.156,0.156 10 false *a 0.958,1.479 1.208,1.635 0.25,0.156 10 false IG+ 0.823,2.938 1.042,3.146 0.219,0.208 10 false B

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G34-1 (IG+) - Body ground Power switch on (IG) 11 to 14 V
G34-21 (B) - Body ground Power switch off 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)