There may be an open circuit in one of the V bus main lines and/or a DLC3 branch line when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.
| Symptom | Trouble Area |
|---|---|
| Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher. | ·
DLC3 branch line or connector ·
CAN main bus line or connector ·
ECM ·
Combination meter assembly ·
CAN junction connector LH ·
CAN junction connector RH |
This malfunction is not related to the lines of a CAN main bus branch or to ECUs or sensors connected to a CAN main bus branch.
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).
Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G4-6 (CANH) - G4-14 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *1 | DLC3 |
When the measured value is 133 Ω or higher and a CAN communication system DTC is output, there may be a fault besides disconnection of the DLC3 branch line. For that reason, troubleshooting should be performed again from How to Proceed with Troubleshooting after repairing the trouble area (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
OK
NG
Disconnect the G1 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G1-31 (CANH) - G1-32 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
OK
NG
Reconnect the G1 combination meter assembly connector.
Disconnect the A40 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A40-13 (CANH) -A40-26 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to ECM) |
OK
NG
Reconnect the A40 ECM connector.
Disconnect the G72 CAN junction connector RH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| G72-7 (CANH) - G72-18 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | Combination meter assembly |
| G72-10 (CANH) - G72-21 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | CAN junction connector LH |
| *a | Front view of wire harness connector
(to CAN Junction Connector RH) |
| *b | to Combination Meter Assembly |
| *c | to CAN Junction Connector LH |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Combination meter assembly main lines) | B |
| NG (CAN junction connector LH main lines) | C |
A
B
C
Reconnect the G72 CAN junction connector RH.
Disconnect the G86 CAN junction connector LH (instrument panel wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| G86-4 (CANH) - G86-15 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | CAN junction connector RH |
| *a | Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side)) |
| *b | to CAN Junction Connector RH |
OK
NG
Reconnect the G86 CAN junction connector LH (instrument panel wire side).
Disconnect the A74 CAN junction connector LH (engine room main wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| A74-9 (CANH) - A74-20 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | ECM |
| *a | Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side)) |
| *b | to ECM |
OK
NG