Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2011.12–2014.12
RM2170E _57 Power Source / Network _057033 NETWORKING _0278068 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Power Management Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Power Management Control ECU Communication Stop Mode
·

"Power Management2" and/or "Hybrid Vehicle Control" is not displayed on the Communication Bus Check screen of the intelligent tester (See page (Click here)).

·

Applies to Power Management Control ECU Communication Stop Mode in DTC Combination Table (See page (Click here)).


·

Power management control ECU branch line or connector

·

Power source circuit of power management control ECU

·

Power management control ECU ground circuit

·

Power management control ECU



WIRING DIAGRAM

C252854E17
2.51,1.281 2.26,0.646 2.26,0.646 2.021,0.646 false 4.333,1.281 4.083,0.646 4.083,0.646 3.844,0.646 false 6.365,2.813 6.708,2.979 0.344,0.167 10 false ECM 4.781,0.552 5.156,0.698 0.375,0.146 10 false DLC3 1.25,3.729 2.104,3.906 0.854,0.177 10 false Trouble Area 0.104,0.115 1.354,0.313 1.25,0.198 12 false V Bus (for LHD): 0.365,2.823 1.604,3.167 1.24,0.344 10 false Combination Meter Assembly 1.094,0.552 2,1.198 0.906,0.646 10 false CAN Junction Connector RH 3.01,4.135 5.146,4.417 2.135,0.281 10 false Power Management Control ECU 3.042,3.781 3.313,3.927 0.271,0.146 10 false A38 3.052,3.396 3.344,3.573 0.292,0.177 10 false A39 3.74,3.073 4.021,3.219 0.281,0.146 10 false G58 4.125,3.073 4.406,3.219 0.281,0.146 10 false G58 2.24,3.938 3.094,4.344 0.854,0.406 10 false IGCT NO. 2 3.604,3.281 3.99,3.438 0.385,0.156 10 false CA1H 4.135,3.281 4.5,3.458 0.365,0.177 10 false CA1L 3.385,3.406 3.656,3.552 0.271,0.146 10 false +B1 3.375,3.771 3.646,3.917 0.271,0.146 10 false +B2 4.573,3.552 4.76,3.708 0.188,0.156 10 false E1 4.917,3.375 5.021,3.521 0.104,0.146 10 false 6 3.146,3.24 3.25,3.385 0.104,0.146 10 false 5 3.135,3.604 3.229,3.75 0.094,0.146 10 false 2 3.521,3.063 3.688,3.208 0.167,0.146 10 false 25 4.49,3.073 4.656,3.219 0.167,0.146 10 false 24 6.188,2.208 6.583,2.385 0.396,0.177 10 false 120 Ω 0.729,2.198 1.125,2.375 0.396,0.177 10 false 120 Ω 0.135,2.823 0.594,3.083 0.458,0.26 10 false G1 6.052,2.813 6.323,2.958 0.271,0.146 10 false A40 1.115,5.01 3.031,5.333 1.917,0.323 10 false : CAN Main Bus Line (CANH) 1.104,5.417 3.021,5.74 1.917,0.323 10 false : CAN Main Bus Line (CANL) 4.271,5 6.031,5.323 1.76,0.323 10 false : CAN Branch Line (CANH) 4.271,5.406 6.01,5.729 1.74,0.323 10 false : CAN Branch Line (CANL) 4.823,3.563 5.104,3.719 0.281,0.156 10 false G57 2.927,0.552 3.833,1.198 0.906,0.646 10 false CAN Junction Connector LH

C251627E07
1.823,1.281 1.573,0.646 1.573,0.646 1.333,0.646 false 4.323,1.281 4.073,0.646 4.073,0.646 3.844,0.646 false 6.365,2.813 6.708,2.979 0.344,0.167 10 false ECM 2.083,0.542 2.458,0.688 0.375,0.146 10 false DLC3 1.24,3.729 2.094,3.906 0.854,0.177 10 false Trouble Area 0.094,0.042 1.448,0.24 1.354,0.198 12 false V Bus (for RHD): 0.375,2.823 1.615,3.167 1.24,0.344 10 false Combination Meter Assembly 0.417,0.542 1.323,1.188 0.906,0.646 10 false CAN Junction Connector RH 3.01,4.146 5.146,4.427 2.135,0.281 10 false Power Management Control ECU 3.042,3.781 3.313,3.927 0.271,0.146 10 false A38 3.042,3.396 3.333,3.573 0.292,0.177 10 false A39 3.74,3.083 4.021,3.229 0.281,0.146 10 false G58 4.135,3.073 4.417,3.219 0.281,0.146 10 false G58 2.229,3.927 3.156,4.229 0.927,0.302 10 false IGCT NO. 2 3.604,3.281 3.99,3.438 0.385,0.156 10 false CA1H 4.135,3.292 4.5,3.469 0.365,0.177 10 false CA1L 3.385,3.385 3.656,3.531 0.271,0.146 10 false +B1 3.375,3.781 3.646,3.927 0.271,0.146 10 false +B2 4.573,3.563 4.76,3.719 0.188,0.156 10 false E1 4.927,3.375 5.031,3.521 0.104,0.146 10 false 6 3.146,3.208 3.25,3.354 0.104,0.146 10 false 5 3.135,3.604 3.229,3.75 0.094,0.146 10 false 2 3.51,3.063 3.677,3.208 0.167,0.146 10 false 25 4.49,3.073 4.656,3.219 0.167,0.146 10 false 24 6.177,2.208 6.573,2.385 0.396,0.177 10 false 120 Ω 0.729,2.198 1.125,2.375 0.396,0.177 10 false 120 Ω 0.125,2.823 0.625,3.063 0.5,0.24 10 false G1 6.083,2.813 6.354,2.958 0.271,0.146 10 false A40 1.115,5.01 3.031,5.333 1.917,0.323 10 false : CAN Main Bus Line (CANH) 1.115,5.417 3.031,5.74 1.917,0.323 10 false : CAN Main Bus Line (CANL) 4.26,4.99 6.021,5.313 1.76,0.323 10 false : CAN Branch Line (CANH) 4.26,5.417 6,5.74 1.74,0.323 10 false : CAN Branch Line (CANL) 4.833,3.552 5.115,3.708 0.281,0.156 10 false G57 2.927,0.552 3.833,1.198 0.906,0.646 10 false CAN Junction Connector LH

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (POWER MANAGEMENT CONTROL ECU BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U158844E03
2.469,2.51 1.646,2.219 false 2.427,2.521 1.677,2.469 false 2.51,2.969 2.99,3.208 0.479,0.24 10 false G58 1.24,2.104 1.604,2.281 0.365,0.177 10 false CA1L 1.25,2.396 1.844,2.615 0.594,0.219 10 false CA1H 0.177,0.135 0.531,0.354 0.354,0.219 10 false *a

Disconnect the power management control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Value
G58-25 (CA1H) - G58-24 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)



OK

2.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (POWER MANAGEMENT CONTROL ECU)

2.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)
a.

Reconnect the (G58) power management control ECU connector.


b.

Disconnect the (G57) power management control ECU connector.


c.
U159353E01
2.473,0.965 2.753,1.118 0.280,0.153 10 G58 1.901,0.965 2.181,1.118 0.280,0.153 10 G57 1.306,0.961 1.586,1.114 0.280,0.153 10 A39 1.218,2.575 1.409,2.728 0.191,0.153 10 E1 0.663,0.961 0.943,1.114 0.280,0.153 10 A38 0.122,0.091 0.300,0.244 0.178,0.153 10 *a 1.84,2.656 1.44,2.656 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Value
G57-6 (E1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND TERMINAL)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.

Reconnect the (G57) power management control ECU connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.
U183292E01
2.488,0.828 2.772,0.981 0.284,0.153 10 G58 1.911,0.828 2.195,0.981 0.284,0.153 10 G57 1.279,0.828 1.563,0.981 0.284,0.153 10 A39 0.675,0.828 0.959,0.981 0.284,0.153 10 A38 0.1,0.061 0.278,0.214 0.179,0.153 10 *a 0.551,2.422 0.835,2.575 0.284,0.153 10 +B2 1.145,2.422 1.429,2.575 0.284,0.153 10 +B1 0.949,1.693 0.736,2.414 false 1.333,1.695 1.31,2.406 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Value
A39-5 (+B1) - Body ground Power switch on (IG) 11 to 14 V
A38-2 (+B2) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Component with harness connected
(Power Management Control ECU)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE TERMINAL)