Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2011.12–2014.12
RM2170E _57 Power Source / Network _057033 NETWORKING _0278069 LIN COMMUNICATION SYSTEM U

NETWORKING  LIN COMMUNICATION SYSTEM  TERMINALS OF ECU  


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


a.

Disconnect the MB main body ECU (multiplex network body ECU) connector.

U183415E02
4.052,1.031 4.052,0.625 4.052,0.625 4.167,0.625 false 1.677,1.417 1.927,1.417 false 0.729,2.677 1.042,2.677 false 1.625,0.854 1.625,0.427 1.625,0.427 1.802,0.427 false 4.219,0.552 4.448,0.688 0.229,0.135 10 false MB 3.448,7.896 3.677,8.031 0.229,0.135 10 false MB 0.396,2.531 0.76,2.688 0.365,0.156 10 false 3E*B 0.396,2.688 0.813,2.833 0.417,0.146 10 false 3F*C 5.031,5.208 5.24,5.344 0.208,0.135 10 false 3C 0.906,1.354 1.104,1.49 0.198,0.135 10 false 3D 0.146,0.094 0.344,0.229 0.198,0.135 10 false *A 5.042,3.833 5.24,3.99 0.198,0.156 10 false *B 5.615,3.833 5.813,4.01 0.198,0.177 10 false *C 1.823,5.198 2.021,5.333 0.198,0.135 10 false 3D 5.875,1.313 6.073,1.448 0.198,0.135 10 false 3B 1.823,6.563 2.021,6.698 0.198,0.135 10 false 3B 5.875,2 6.063,2.135 0.188,0.135 10 false 3A 5.083,6.563 5.271,6.698 0.188,0.135 10 false 3A 0.906,1.99 1.115,2.125 0.208,0.135 10 false 3C 1.938,1.323 2.302,1.542 0.365,0.219 10 false G59 1.833,0.344 2.125,0.479 0.292,0.135 10 false *1 5.333,3.865 5.563,4 0.229,0.135 10 false 3F 1.719,3.865 2.01,4 0.292,0.135 10 false G59 4.76,3.865 5.021,4 0.26,0.135 10 false 3E

Text in Illustration
*A Main body ECU (multiplex network body ECU) with 1 connector *B for LHD
*C for RHD - -
*1 Main body ECU (multiplex network body ECU) - -

U183433E02
1.635,0.958 1.635,0.615 1.635,0.615 1.771,0.615 false 4.094,1.146 4.094,0.635 4.094,0.635 4.229,0.635 false 1.677,1.531 1.948,1.531 false 1.677,1.958 1.948,1.958 false 0.771,2.719 1.042,2.719 false 2.219,3.792 2.5,3.948 0.281,0.156 10 false G60 4.698,3.802 4.979,3.958 0.281,0.156 10 false G59 1.156,5.063 1.438,5.219 0.281,0.156 10 false 3D 3.927,5.042 4.208,5.198 0.281,0.156 10 false 3C 1.813,6.313 2.094,6.469 0.281,0.156 10 false 3B 3.469,7.563 3.75,7.719 0.281,0.156 10 false MB 4.927,6.302 5.208,6.458 0.281,0.156 10 false 3A 5.896,5.052 6.177,5.208 0.281,0.156 10 false 3F 0.146,0.083 0.427,0.24 0.281,0.156 10 false *A 1.813,0.531 2.094,0.688 0.281,0.156 10 false *1 1.969,1.469 2.26,1.625 0.292,0.156 10 false G59 1.969,1.885 2.26,2.042 0.292,0.156 10 false G60 4.271,0.563 4.563,0.76 0.292,0.198 10 false MB 5.875,1.417 6.156,1.573 0.281,0.156 10 false 3B 5.875,2.094 6.156,2.25 0.281,0.156 10 false 3A 0.906,1.417 1.188,1.573 0.281,0.156 10 false 3D 0.906,2.094 1.188,2.25 0.281,0.156 10 false 3C 0.552,2.656 0.771,2.813 0.219,0.156 10 false 3F

Text in Illustration
*A Main body ECU (multiplex network body ECU) with 2 connectors - -
*1 Main body ECU (multiplex network body ECU) - -


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
MB-30 (BECU) - Body ground - Auxiliary battery power supply Power switch off 11 to 14 V
MB-32 (IG) - Body ground - IG power supply Power switch on (IG) 11 to 14 V
MB-29 (ACC) - Body ground - ACC power supply Power switch on (ACC) 11 to 14 V
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reinstall the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.


d.

Check for pulses according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
3B-12 (LIN2) - 3B-8 (GND1) B - W-B LIN communication line Power switch on (IG) Pulse generation

If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may be malfunctioning.



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)


a.

Disconnect the J3*1 or H3*2 power window regulator motor assembly (for driver door) connector.

*1: for LHD

*2: for RHD


U183386E02
2.25,0.823 2.469,0.969 0.219,0.146 10 false J3 2.5,0.802 2.719,0.948 0.219,0.146 10 false *A 2.51,1.094 2.729,1.24 0.219,0.146 10 false *B 2.24,1.115 2.458,1.26 0.219,0.146 10 false H3

Text in Illustration
*A for LHD *B for RHD


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
J3-2 (B) - J3-1 (GND) LA-G - LA Auxiliary battery power supply Power switch off 11 to 14 V
J3-1 (GND) - Body ground LA - Body ground Ground Always Below 1 Ω

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
H3-2 (B) - H3-1 (GND) LA-LG - LA Auxiliary battery power supply Power switch off 11 to 14 V
H3-1 (GND) - Body ground LA - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the J3*1 or H3*2 power window regulator motor assembly (for driver door) connector.

*1: for LHD

*2: for RHD



d.

Check for pulses according to the value(s) in the table below.

for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
J3-9 (LIN) - J3-1 (GND) B - LA LIN communication line Power switch on (IG) Pulse generation

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
H3-9 (LIN) - H3-1 (GND) B - LA LIN communication line Power switch on (IG) Pulse generation

If the result is not as specified, the power window regulator motor assembly (for driver door) may be malfunctioning.



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


a.

Disconnect the G54 and G55 certification ECU (smart key ECU assembly) connectors.

U183407E02
2.208,0.219 2.521,0.385 0.313,0.167 10 false G53 3.615,0.219 3.906,0.385 0.292,0.167 10 false G54 4.792,0.219 5.094,0.385 0.302,0.167 10 false G55


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
G54-5 (+B) - G55-1 (E) BE - W-B Auxiliary battery power supply Power switch off 11 to 14 V
G55-1 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the G55 and G54 certification ECU (smart key ECU assembly) connectors.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
G54-16 (IG) - G55-1 (E) V - W-B IG power supply Power switch on (IG) 11 to 14 V
G54-16 (IG) - G55-1 (E) V - W-B IG power supply Power switch off Below 1 V
G54-12 (LIN) - G55-1 (E) LG - W-B LIN communication line Power switch on (IG) Pulse generation

If the result is not as specified, the certification ECU (smart key ECU assembly) may be malfunctioning.



CHECK POWER MANAGEMENT CONTROL ECU


a.

Disconnect the G57 and G58 power management control ECU connectors.

U183499E02
1.406,0.167 1.698,0.344 0.292,0.177 10 false A38 2.771,0.167 3.073,0.344 0.302,0.177 10 false A39 4.26,0.167 4.563,0.344 0.302,0.177 10 false G57 5.51,0.167 5.813,0.344 0.302,0.177 10 false G58


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
G57-1 (AM22) - Body ground B - Body ground Auxiliary battery power supply Power switch off 11 to 14 V
G58-7 (AM21) - Body ground B - Body ground Auxiliary battery power supply Power switch off 11 to 14 V
G57-6 (E1) - Body ground BR - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the G57 and G58 power management control ECU connectors.


d.

Check for pulses according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
G58-11 (LIN2) - G57-6 (E1) LG - BR LIN communication line Power switch on (IG) Pulse generation

If the result is not as specified, the power management control ECU may be malfunctioning.



CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)


a.
U159348E02
1.573,0.281 2.177,0.698 0.604,0.417 10 false G50

Disconnect the G50 steering lock ECU (steering lock actuator assembly) connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G50-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
G50-7 (B) - Body ground GR - Body ground Auxiliary battery power supply Power switch off 11 to 14 V
G50-6 (IG2) - Body ground SB - Body ground IG power supply Power switch on (IG) 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the G50 steering lock ECU (steering lock actuator assembly) connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
G50-5 (LIN) - G50-1 (GND) LG - W-B LIN communication line Power switch on (IG) Pulse generation

If the result is not as specified, the steering lock ECU (steering lock actuator assembly) may be malfunctioning.



CHECK ID CODE BOX (IMMOBILISER CODE ECU)


a.

Disconnect the G49 ID code box (immobiliser code ECU) connector.

U159208E02
3.438,0.25 3.969,0.521 0.531,0.271 10 false G49


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
G49-1 (+B) - G49-5 (GND) BE - W-B Auxiliary battery power supply Power switch off 11 to 14 V
G49-5 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the G49 ID code box (immobiliser code ECU) connector.


d.

Check for pulses according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
G49-2 (LIN1) - G49-5 (GND) LG - W-B LIN communication line Power switch on (IG) Pulse generation

If the result is not as specified, the ID code box (immobiliser code ECU) may be malfunctioning.