Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2011.12–2014.12
RM2170E _57 Power Source / Network _057033 NETWORKING _0278069 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2786  No Response from Steering Lock ECU  


DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly) stops for 10 seconds or more.

DTC No. DTC Detection Condition Trouble Area
B2786 No communication between steering lock ECU (steering lock actuator assembly) and certification ECU (smart key ECU assembly) for 10 seconds or more.
·

Steering lock ECU (steering lock actuator assembly)

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector



WIRING DIAGRAM

B273275E22
0.955,2.497 2.518,2.838 1.563,0.341 10 Certification ECU (Smart Key ECU Assembly) 3.771,2.49 5.672,2.963 1.901,0.473 10 Steering Lock ECU (Steering Lock Actuator Assembly) 0.955,2.343 1.354,2.497 0.399,0.154 10 G54 3.777,2.327 4.102,2.480 0.325,0.154 10 G50 1.805,1.477 2.081,1.624 0.276,0.147 10 LIN 4.243,1.463 4.519,1.610 0.276,0.147 10 LIN 5.452,1.211 6.275,1.367 0.823,0.156 10 STRG LOCK 4.995,1.061 5.146,1.217 0.151,0.156 10 B 4.75,2.002 5.116,2.158 0.367,0.156 10 GND 4.345,0.372 5.726,0.528 1.380,0.156 10 from Auxiliary Battery 0.661,3.481 2.277,3.636 1.617,0.156 10 : LIN Communication Line 2.159,1.337 2.348,1.490 0.188,0.154 10 12 4.038,1.321 4.227,1.475 0.188,0.154 10 5 5.18,0.957 5.368,1.110 0.188,0.154 10 7 5.187,1.903 5.299,2.056 0.112,0.154 10 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

If the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is replaced, refer to Service Bulletin.

·

When using the intelligent tester to troubleshoot with the power switch off:

Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.



PROCEDURE

1.CHECK DTC OUTPUT

b.

Recheck for DTCs.

Result:
Result Proceed to
Only B2786 is output A
DTC B2786 and B2785 are output simultaneously B


HINT:

When DTC B2786 and B2785 are output simultaneously, perform troubleshooting for DTC B2785 first.




A

2.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - AUXILIARY BATTERY AND BODY GROUND)

B

2.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the G50 steering lock ECU (steering lock actuator assembly) connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G50-1 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
G50-7 (B) - Body ground Power switch off 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - STEERING LOCK ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - STEERING LOCK ECU)
a.

Disconnect the G54 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G54-12 (LIN) - G50-5 (LIN) Always Below 1 Ω
G54-12 (LIN) - Body ground Always 10 kΩ or higher




OK

4.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.

Replace the steering lock ECU (steering lock actuator assembly) (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>REMOVAL).



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT

b.

Recheck for DTCs.

OK:

DTC B2786 is not output.




OK

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)