Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2011.12–2014.12
RM2170E _57 Power Source / Network _057033 NETWORKING _0278069 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2789  No Response from ID BOX  


DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) stops for 10 seconds or more.

DTC No. DTC Detection Condition Trouble Area
B2789 No communication between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) for 10 seconds or more.
·

ID code box (immobiliser code ECU)

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector



WIRING DIAGRAM

B273275E23
0.904,2.57 2.448,2.882 1.545,0.312 10 Certification ECU (Smart Key ECU Assembly) 3.931,2.57 5.470,2.892 1.539,0.323 10 ID Code Box (Immobiliser Code ECU) 0.904,2.406 1.221,2.553 0.318,0.147 10 G54 3.945,2.406 4.240,2.544 0.295,0.137 10 G49 1.856,1.479 2.098,1.633 0.242,0.154 10 LIN 4.224,1.479 4.558,1.633 0.334,0.154 10 LIN1 2.155,1.346 2.339,1.511 0.184,0.165 10 12 4.065,1.346 4.201,1.511 0.136,0.165 10 2 4.904,1.09 5.101,1.244 0.197,0.154 10 +B 4.794,2.028 5.128,2.182 0.334,0.154 10 GND 5.171,0.994 5.272,1.159 0.100,0.165 10 1 5.171,1.925 5.290,2.090 0.119,0.165 10 5 5.431,1.234 6.337,1.371 0.906,0.137 10 ECU-B NO. 2 4.362,0.393 5.712,0.568 1.350,0.174 10 from Auxiliary Battery 0.669,3.488 2.297,3.635 1.628,0.147 10 : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

If the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is replaced, refer to Service Bulletin.

·

When using the intelligent tester to troubleshoot with the power switch off:

Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.



PROCEDURE

1.CHECK DTC OUTPUT

b.

Recheck for DTCs.

Result:
Result Proceed to
Only B2789 is output A
DTC B2789 and B2785 are output simultaneously B


HINT:

When DTC B2789 and B2785 are output simultaneously, perform troubleshooting for DTC B2785 first.




A

2.CHECK HARNESS AND CONNECTOR (ID CODE BOX - AUXILIARY BATTERY AND BODY GROUND)

B

2.CHECK HARNESS AND CONNECTOR (ID CODE BOX - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the G49 ID code box (immobiliser code ECU).


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G49-5 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
G49-1 (+B) - Body ground Power switch off 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - ID CODE BOX)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - ID CODE BOX)
a.

Disconnect the G54 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G54-12 (LIN) - G49-2 (LIN1) Always Below 1 Ω
G54-12 (LIN) - Body ground Always 10 kΩ or higher




OK

4.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU).

HINT:

Refer to Service Bulletin.




NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT

b.

Recheck for DTCs.

OK:

DTC B2789 is not output.




OK

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)