Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2011.12–2014.12
RM2170E _57 Power Source / Network _057033 NETWORKING _0278069 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B278C  Lost Communication with Power Source Control  


DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and power management control ECU stops for 10 seconds or more.

DTC No. DTC Detection Condition Trouble Area
B278C No communication between the certification ECU (smart key ECU assembly) and power management control ECU for 10 seconds or more.
·

Power management control ECU

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector



WIRING DIAGRAM

B228566E13
0.701,3.469 2.329,3.625 1.628,0.156 10 : LIN Communication Line 0.89,2.509 2.448,2.825 1.559,0.316 10 Certification ECU (Smart Key ECU Assembly) 4.049,2.509 5.344,2.825 1.295,0.316 10 Power Management Control ECU 0.89,2.341 1.249,2.490 0.360,0.149 10 G54 1.849,1.465 2.102,1.628 0.253,0.163 10 LIN 4.231,1.465 4.568,1.628 0.336,0.163 10 LIN2 4.745,1.064 5.128,1.226 0.383,0.163 10 AM22 4.745,1.447 5.128,1.609 0.383,0.163 10 AM21 4.932,1.979 5.129,2.142 0.198,0.163 10 E1 2.155,1.332 2.334,1.474 0.179,0.142 10 12 3.891,1.475 4.186,1.623 0.295,0.149 10 G58 5.185,1.071 5.475,1.220 0.290,0.149 10 G57 5.185,1.456 5.475,1.605 0.290,0.149 10 G58 5.185,1.993 5.494,2.142 0.309,0.149 10 G57 3.954,1.297 4.152,1.446 0.198,0.149 10 11 5.285,0.895 5.386,1.044 0.100,0.149 10 1 5.285,1.283 5.386,1.432 0.100,0.149 10 7 5.285,1.825 5.386,1.974 0.100,0.149 10 6 6.02,1.218 6.333,1.381 0.313,0.163 10 AM2 4.591,0.391 5.946,0.554 1.355,0.163 10 from Auxiliary Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

If the certification ECU (smart key ECU assembly) or power management control ECU is replaced, refer to Service Bulletin.

·

When using the intelligent tester to troubleshoot with the power switch off:

Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.



PROCEDURE

1.CHECK DTC OUTPUT

b.

Recheck for DTCs.

Result:
Result Proceed to
Only B278C is output A
DTC B278C and B2785 are output simultaneously B


HINT:

When DTC B278C and B2785 are output simultaneously, perform troubleshooting for DTC B2785 first.




A

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - AUXILIARY BATTERY AND BODY GROUND)

B

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the G57 and G58 power management control ECU connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G57-6 (E1) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
G57-1 (AM22) - Body ground Power switch off 11 to 14 V
G58-7 (AM21) - Body ground Power switch off 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER MANAGEMENT CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the G54 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G54-12 (LIN) - G58-11 (LIN2) Always Below 1 Ω
G54-12 (LIN) - Body ground Always 10 kΩ or higher




OK

4.REPLACE POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE POWER MANAGEMENT CONTROL ECU
a.

Replace the power management control ECU (See page Power Source / Network>POWER DISTRIBUTION>POWER MANAGEMENT CONTROL ECU>REMOVAL).



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT

b.

Recheck for DTCs.

OK:

DTC B278C is not output.




OK

END (POWER MANAGEMENT CONTROL ECU WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)