CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *A | Main body ECU (multiplex network body ECU) with 1 connector | *B | for LHD |
| *C | for RHD | - | - |
| *1 | Main body ECU (multiplex network body ECU) | - | - |
| *A | Main body ECU (multiplex network body ECU) with 2 connectors | - | - |
| *1 | Main body ECU (multiplex network body ECU) | - | - |
Disconnect the MB and G59 main body ECU (multiplex network body ECU) connector.
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connectors disconnected.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| MB-11 (GND1) - Body ground | - | Ground | Always | Below 1 Ω |
| MB-30 (BECU) - Body ground | - | Auxiliary battery power supply | Power switch off | 11 to 14 V |
| MB-29 (ACC) - Body ground | - | ACC power supply | Power switch on (ACC) | 11 to 14 V |
| MB-29 (ACC) - Body ground | - | ACC power supply | Power switch off | Below 1 V |
| MB-32 (IG) - Body ground | - | Power switch power supply | Power switch on (IG) | 11 to 14 V |
| MB-32 (IG) - Body ground | - | Power switch power supply | Power switch off | Below 1 V |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the MB and G59 main body ECU (multiplex network body ECU) connector.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 3B-3 (ACT-) - Body ground | R - Body ground | Door lock motor unlock drive output (all doors) | Door control switch (multiplex network master switch) or driver door key cylinder off | Below 1 V |
| 3B-3 (ACT-) - Body ground | R - Body ground | Door lock motor unlock drive output (all doors) | Door control switch (multiplex network master switch) or driver door key cylinder unlocked | 11 to 14 V |
| 3B-1 (ACT+) - Body ground | Y - Body ground | Door lock motor lock drive output (all doors) | Door control switch (multiplex network master switch) or driver door key cylinder off | Below 1 V |
| 3B-1 (ACT+) - Body ground | Y - Body ground | Door lock motor lock drive output (all doors) | Door control switch (multiplex network master switch) or driver door key cylinder locked | 11 to 14 V |
| G59-19 (FRCY) - Body ground | R - Body ground | Front door courtesy light switch RH input | Front door RH open | Below 1 V |
| G59-19 (FRCY) - Body ground | R - Body ground | Front door courtesy light switch RH input | Front door RH closed | Pulse generation |
| 3D-36 (FLCY) - Body ground | R - Body ground | Front door courtesy light switch LH input | Front door LH open | Below 1 V |
| 3D-36 (FLCY) - Body ground | R - Body ground | Front door courtesy light switch LH input | Front door LH closed | Pulse generation |
| G59-24 (LCTY) - Body ground | L - Body ground | Rear door courtesy light switch LH input | Rear door LH open | Below 1 V |
| G59-24 (LCTY) - Body ground | L - Body ground | Rear door courtesy light switch LH input | Rear door LH closed | Pulse generation |
| G59-6 (RCTY) - Body ground | G - Body ground | Rear door courtesy light switch RH input | Rear door RH open | Below 1 V |
| G59-6 (RCTY) - Body ground | G - Body ground | Rear door courtesy light switch RH input | Rear door RH closed | Pulse generation |
| G59-9 (L1) - Body ground | V - Body ground | Door control switch input | Door control switch locked | Below 1 V |
| G59-9 (L1) - Body ground | V - Body ground | Door control switch input | Door control switch off | Pulse generation |
| G59-10 (UL1) - Body ground | BE - Body ground | Door control switch input | Door control switch unlocked | Below 1 V |
| G59-10 (UL1) - Body ground | BE - Body ground | Door control switch input | Door control switch off | Pulse generation |
| G59-11 (L2) - Body ground | SB*1 - Body ground
B*2 - Body ground |
Driver door key-linked lock input | Driver door key cylinder turned to lock | Below 1 V |
| G59-11 (L2) - Body ground | SB*1 - Body ground
B*2 - Body ground |
Driver door key-linked lock input | Driver door key cylinder off | Pulse generation |
| G59-12 (UL2) - Body ground | LG*1 - Body ground
G*2 - Body ground |
Driver door key-linked unlock input | Driver door key cylinder turned to unlock | Below 1 V |
| G59-12 (UL2) - Body ground | LG*1 - Body ground
G*2 - Body ground |
Driver door key-linked unlock input | Driver door key cylinder off | Pulse generation |
| G59-7 (LSFL) - Body ground | L - Body ground | Front door LH unlock detection switch input | Front door LH unlocked | Below 1 V |
| G59-7 (LSFL) - Body ground | L - Body ground | Front door LH unlock detection switch input | Front door LH locked | Pulse generation |
| G59-18 (LSFR) - Body ground | L - Body ground | Front door RH unlock detection switch input | Front door RH unlocked | Below 1 V |
| G59-18 (LSFR) - Body ground | L - Body ground | Front door RH unlock detection switch input | Front door RH locked | Pulse generation |
| 3D-25 (LSR) - Body ground | V - Body ground | Rear door RH unlock detection switch input | Rear door RH or LH unlocked | Below 1 V |
| 3D-25 (LSR) - Body ground | V - Body ground | Rear door RH unlock detection switch input | Rear door RH and LH locked | Pulse generation |
| 3D-24 (LSR) - Body ground | Y - Body ground | Rear door LH unlock detection switch input | Rear door LH or RH unlocked | Below 1 V |
| 3D-24 (LSR) - Body ground | Y - Body ground | Rear door LH unlock detection switch input | Rear door LH and RH locked | Pulse generation |
| 3D-35 (BCTY) - Body ground | B - Body ground | Back door courtesy light switch input | Back door open | Below 1 V |
| 3D-35 (BCTY) - Body ground | B - Body ground | Back door courtesy light switch input | Back door closed | 11 to 14 V |
| 3D-9 (TR+) - Body ground | Y - Body ground | Back door lock motor unlock drive output | Back door opener switch (open switch) pushed | 11 to 14 V |
| 3D-9 (TR+) - Body ground | Y - Body ground | Back door lock motor unlock drive output | Back door opener switch (open switch) not pushed | Below 1 V |
*1: for LHD
*2: for RHD
If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Disconnect the G78 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G78-27 (TSW5) - Body ground | L - Body ground | Back door opener switch signal | Back door opener switch on | Below 1 Ω |
| G78-27 (TSW5) - Body ground | L - Body ground | Back door opener switch signal | Back door opener switch off | 10 kΩ or higher |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the G78 certification ECU (smart key ECU assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G78-27 (TSW5) - Body ground | L - Body ground | Back door opener switch signal | Back door opener switch off | Pulse generation |
| G78-27 (TSW5) - Body ground | L - Body ground | Back door opener switch signal | Back door opener switch on | Below 1 V |
If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.