Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › 2011.12–2017.06
RM2170E _58 Vehicle Interior _057034 DOOR LOCK _0278072 POWER DOOR LOCK CONTROL SYSTEM U

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Main Body (Main Body ECU (Multiplex Network Body ECU))
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Door Courtesy Rear door courtesy light switch RH signal/CLOSE or OPEN CLOSE: Rear door RH closed
OPEN: Rear door RH open
-
RL Door Courtesy Rear door courtesy light switch LH signal/CLOSE or OPEN CLOSE: Rear door LH closed
OPEN: Rear door LH open
-
Back Door Courtesy SW Back door courtesy switch signal/ ON or OFF ON: Back door open
OFF: Back door closed
-
Back Door Open Back door lock/Permit or Prohibt Permit: Back door unlocked
Prohibt: Back door locked
-
Door Lock SW-Lock Door control switch (power window regulator master switch assembly) lock signal/ON or OFF ON: Lock side of door control switch (power window regulator master switch assembly) pushed
OFF: Lock side of door control switch (power window regulator master switch assembly) not pushed
-
Door Lock SW-Unlock Door control switch (power window regulator master switch assembly) unlock signal/ON or OFF ON: Unlock side of door control switch (power window regulator master switch assembly) pushed
OFF: Unlock side of door control switch (power window regulator master switch assembly) not pushed
-
Door Key SW-Lock Driver door key-linked lock/unlock switch lock signal/ON or OFF ON: Driver door key cylinder turned to lock position
OFF: Driver door key cylinder not turned to lock position
-
Door Key SW-Unlock Driver door key-linked lock/unlock switch unlock signal/ON or OFF ON: Driver door key cylinder turned to unlock position
OFF: Driver door key cylinder not turned to unlock position
-
FR Door Lock Pos Front door RH unlock detection switch signal/LOCK or UNLOCK LOCK: Front door RH locked
UNLOCK: Front door RH unlocked
-
FR Door Courtesy Front door courtesy light switch RH signal/CLOSE or OPEN CLOSE: Front door RH closed
OPEN: Front door RH open
-
FL Door Lock Pos Front door LH unlock detection switch signal/LOCK or UNLOCK LOCK: Front door LH locked
UNLOCK: Front door LH unlocked
-
FL Door Courtesy Front door courtesy light switch LH signal/CLOSE or OPEN CLOSE: Front door LH closed
OPEN: Front door LH open
-
RR-Door Lock Pos SW Rear door RH and LH unlock detection switch signal/ON or OFF ON: Rear door RH or LH unlocked
OFF: Rear door RH and LH locked
-
RL-Door Lock Pos SW Rear door RH and LH unlock detection switch signal/ON or OFF ON: Rear door RH or LH unlocked
OFF: Rear door RH and LH locked
-



ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Main Body (Main Body ECU (Multiplex Network Body ECU))
Tester Display Test Part Control Range Diagnostic Note
Door Lock Door lock motor Unlock/Lock -
Trunk and Back-Door Open Back door lock motor OFF/ON -