CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *A | Main body ECU (multiplex network body ECU) with 1 connector | *B | for LHD |
| *C | for RHD | - | - |
| *1 | Main body ECU (multiplex network body ECU) | - | - |
| *A | Main body ECU (multiplex network body ECU) with 2 connectors | *B | for LHD |
| *C | for RHD | - | - |
| *1 | Main body ECU (multiplex network body ECU) | - | - |
Disconnect the MB main body ECU (multiplex network body ECU) connector.
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connectors disconnected.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| MB-11 (GND1) - Body ground | - | Ground | Always | Below 1 Ω |
| MB-30 (BECU) - Body ground | - | Auxiliary battery power supply | Power switch off | 11 to 14 V |
| MB-29 (ACC) - Body ground | - | ACC power supply | Power switch on (ACC) | 11 to 14 V |
| MB-29 (ACC) - Body ground | - | ACC power supply | Power switch off | Below 1 V |
| MB-32 (IG) - Body ground | - | IG power supply | Power switch on (IG) | 11 to 14 V |
| MB-32 (IG) - Body ground | - | IG power supply | Power switch off | Below 1 V |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the MB main body ECU (multiplex network body ECU) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 3B-3 (ACT-) - Body ground | R - Body ground | Door lock motor unlock drive output (all doors) | Door control switch (power window regulator master switch assembly) or driver door key cylinder off | Below 1 V |
| 3B-3 (ACT-) - Body ground | R - Body ground | Door lock motor unlock drive output (all doors) | Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked | 11 to 14 V |
| 3B-1 (ACT+) - Body ground | Y - Body ground | Door lock motor lock drive output (all doors) | Door control switch (power window regulator master switch assembly) or driver door key cylinder off | Below 1 V |
| 3B-1 (ACT+) - Body ground | Y - Body ground | Door lock motor lock drive output (all doors) | Door control switch (power window regulator master switch assembly) or driver door key cylinder locked | 11 to 14 V |
| 3D-36 (FLCY) - Body ground | R - Body ground | Front door LH courtesy light switch input | Front door LH open | Below 1 V |
| 3D-36 (FLCY) - Body ground | R - Body ground | Front door LH courtesy light switch input | Front door LH closed | Pulse generation |
| G59-19 (FRCY) - Body ground | R - Body ground | Front door RH courtesy light switch input | Front door RH open | Below 1 V |
| G59-19 (FRCY) - Body ground | R - Body ground | Front door RH courtesy light switch input | Front door RH closed | Pulse generation |
| G59-24 (LCTY) - Body ground | L - Body ground | Rear door LH courtesy light switch input | Rear door LH open | Below 1 V |
| G59-24 (LCTY) - Body ground | L - Body ground | Rear door LH courtesy light switch input | Rear door LH closed | Pulse generation |
| G59-6 (RCTY) - Body ground | G - Body ground | Rear door RH courtesy light switch input | Rear door RH open | Below 1 V |
| G59-6 (RCTY) - Body ground | G - Body ground | Rear door RH courtesy light switch input | Rear door RH closed | Pulse generation |
| G59-7 (LSFL) - Body ground | L - Body ground | Front door LH unlock detection switch input | Front door LH unlocked | Below 1 V |
| G59-7 (LSFL) - Body ground | L - Body ground | Front door LH unlock detection switch input | Front door LH locked | Pulse generation |
| G59-18 (LSFR) - Body ground | L - Body ground | Front door RH unlock detection switch input | Front door RH unlocked | Below 1 V |
| G59-18 (LSFR) - Body ground | L - Body ground | Front door RH unlock detection switch input | Front door RH locked | Pulse generation |
| 3D-25 (LSR) - Body ground | V - Body ground | Rear door RH unlock detection switch input | Rear door RH unlocked | Below 1 V |
| 3D-25 (LSR) - Body ground | V - Body ground | Rear door RH unlock detection switch input | Rear door RH locked | Pulse generation |
| 3D-24 (LSR) - Body ground | Y - Body ground | Rear door LH unlock detection switch input | Rear door LH unlocked | Below 1 V |
| 3D-24 (LSR) - Body ground | Y - Body ground | Rear door LH unlock detection switch input | Rear door LH locked | Pulse generation |
| 3C-34 (BZR) - Body ground | B - Body ground | Wireless door lock buzzer signal | Wireless door lock buzzer off | Below 1 V |
| 3C-34 (BZR) - Body ground | B - Body ground | Wireless door lock buzzer signal | Wireless door lock buzzer on | Pulse generation |
If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Disconnect the G54 and G55 certification ECU (smart key ECU assembly) connectors.
Measure the resistance and voltage according to the value(s) in the table below.
Measure the values on the wire harness side with the connectors disconnected.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G55-1 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| G54-5 (+B) - Body ground | BE - Body ground | Auxiliary battery power supply | Always | 11 to 14 V |
| G54-4 (CUTB) - Body ground | L - Body ground | Dark current cut fuse pin input signal | Always | 11 to 14 V |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the G54 and G55 certification ECU (smart key ECU assembly) connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G54-16 (IG) - G55-1 (E) | V - W-B | IG power supply | Power switch on (IG) | 11 to 14 V |
| Power switch off | Below 1 V | |||
| G53-7 (RSSI) - G55-1 (E) | R - W-B*1
P - W-B*2 |
Communication channel switching circuit | Power switch off, all doors closed and electrical key transmitter sub-assembly lock/unlock switch not pressed → electrical key transmitter sub-assembly lock/unlock switch pressed | 11 to 14 V → Below 2 V |
| G53-6 (RDAS) - G55-1 (E) | LG - W-B | RF Signal input circuit | All doors closed, all door lock and electrical key transmitter sub-assembly lock/unlock switch not pressed → electrical key transmitter sub-assembly lock/unlock switch pressed | 11 to 14 V pulse generation at regular intervals |
| G53-15 (RCO) - G55-1 (E) | L - W-B | Wireless tuner power supply output circuit | Power switch off and electrical key transmitter sub-assembly lock/unlock switch not pressed → electrical key transmitter sub-assembly lock/unlock switch pressed | Below 1 V → 4.5 to 5.5 V |
*1: for LHD
*2: for RHD
If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.
CHECK DOOR CONTROL RECEIVER
Disconnect the M15 door control receiver connector.
Measure the resistance and voltage according to the value(s) in the table below.
Measure the values on the wire harness side with the connectors disconnected.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| M15-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the M15 door control receiver connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| M15-2 (RSSI) - M15-1 (GND) | Y - W-B | Smart system receiving channel switching signal input | All doors closed, all door lock and electrical key transmitter sub-assembly lock/unlock switch not pressed → electrical key transmitter sub-assembly lock/unlock switch pressed | 11 to 14 V → Below 2 V |
| M15-5 (DATA) - M15-1 (GND) | L - W-B | Smart system recovery code output | All doors closed, all door lock and electrical key transmitter sub-assembly lock/unlock switch not pressed → electrical key transmitter sub-assembly lock/unlock switch pressed | Below 2 V → 11 to 14 V → Below 2 V |
| M15-4 (+5) - M15-1 (GND) | V - W-B | Receive mode switching signal input | Power switch off and electrical key transmitter sub-assembly lock/unlock switch not pressed → electrical key transmitter sub-assembly lock/unlock switch pressed | Below 1 V → 4.5 to 5.5 V |
If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.