Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057034 DOOR LOCK _0278073 WIRELESS DOOR LOCK CONTROL SYSTEM C

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  B1242  Wireless Door Lock Tuner Circuit Malfunction  


DESCRIPTION

The door control receiver is used to receive radio waves relating to the entry functions of the electrical key transmitter sub-assembly. The certification ECU (smart key ECU assembly) decodes the requested electrical key transmitter sub-assembly by identifying a key code based on the radio waves received via the door control receiver. The door control receiver receives a signal from the electrical key transmitter sub-assembly and sends signals to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly). The certification ECU (smart key ECU assembly) then sends a command, according to the requested operation, to each ECU (ex. if door lock operation is requested, the certification ECU (smart key ECU assembly) sends a door lock command to the main body ECU (multiplex network body ECU)).

DTC No. DTC Detection Condition Trouble Area
B1242
·

Short in RDAS to ground between the certification ECU (smart key ECU assembly) and the door control receiver.

·

Short in RSSI to ground between the certification ECU (smart key ECU assembly) and the door control receiver.


·

Wire harness or connector

·

Door control receiver

·

Certification ECU (Smart key ECU assembly)



WIRING DIAGRAM

B281122E47
0.448,4.177 1.885,4.323 1.438,0.146 10 false Door Control Receiver 5.5,4.01 7.042,4.365 1.542,0.354 10 false Certification ECU (Smart Key ECU Assembly) 1.24,1.073 1.635,1.219 0.396,0.146 10 false RSSI 1.208,1.865 1.615,2.021 0.406,0.156 10 false DATA 1.396,2.646 1.615,2.802 0.219,0.156 10 false +5 5.823,1.083 6.229,1.219 0.406,0.135 10 false RSSI 5.823,1.875 6.25,2.021 0.427,0.146 10 false RDAS 5.823,2.677 6.188,2.833 0.365,0.156 10 false RCO 1.708,0.927 1.802,1.063 0.094,0.135 10 false 2 1.708,1.719 1.802,1.854 0.094,0.135 10 false 5 1.708,2.552 1.885,2.688 0.177,0.135 10 false 4 5.531,3.281 5.625,3.427 0.094,0.146 10 false 1 5.49,2.458 5.667,2.594 0.177,0.135 10 false 15 5.531,1.646 5.625,1.781 0.094,0.135 10 false 6 5.823,3.521 5.979,3.677 0.156,0.156 10 false E 5.531,0.854 5.625,0.99 0.094,0.135 10 false 7 1.292,3.49 1.698,3.646 0.406,0.156 10 false GND 1.708,3.344 1.896,3.479 0.188,0.135 10 false 1 0.448,4 0.75,4.146 0.302,0.146 10 false M15 5.427,3.5 5.708,3.646 0.281,0.146 10 false G55 5.427,2.667 5.708,2.813 0.281,0.146 10 false G53 5.427,1.875 5.708,2.021 0.281,0.146 10 false G53 5.427,1.083 5.708,1.229 0.281,0.146 10 false G53

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, smart and wireless function performance may be affected.

·

Before performing the inspection, check that there are no problems related to the CAN communication system (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

This DTC is not detected within 10 seconds after the power switch is turned to off from on (IG).



PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Disconnect the M15 door control receiver connector.


b.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

B440800C10
2.146,0.104 2.521,0.323 0.375,0.219 4.74,0.104 5.115,0.323 0.375,0.219 1.656,1.521 1.833,1.521 1.833,1.521 2,0.771 false 2.885,1.531 2.708,1.531 2.708,1.531 2.573,0.875 false 5.823,1.521 5.604,1.521 5.604,1.521 5.438,0.76 false 1.906,0.719 1.75,0.198 1.75,0.198 1.563,0.198 false 2.229,0.146 2.542,0.344 0.313,0.198 10 false G53 4.813,0.135 5.125,0.333 0.313,0.198 10 false G55 1.229,1.448 1.688,1.656 0.458,0.208 10 false RDAS 2.927,1.448 3.385,1.656 0.458,0.208 10 false RCO 5.875,1.427 6.104,1.615 0.229,0.188 10 false E 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.198,0.125 1.656,0.333 0.458,0.208 10 false RSSI
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Standard Voltage:
Tester Connection Condition Specified Condition
G53-15 (RCO) - G55-1 (E) Always Below 1 V → 4.5 to 5.5 V pulse generation at regular intervals
G53-7 (RSSI) - G55-1 (E) Always 11 to 14 V
G53-6 (RDAS) - G55-1 (E) Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
G55-1 (E) - Body ground Always Below 1 Ω




OK

REPLACE DOOR CONTROL RECEIVER

NG

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the G53 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G53-7 (RSSI) - M15-2 (RSSI) Always Below 1 Ω
G53-6 (RDAS) - M15-5 (DATA) Always Below 1 Ω
G53-15 (RCO) - M15-4 (+5) Always Below 1 Ω
M15-1 (GND) - Body ground Always Below 1 Ω
G53-7 (RSSI) or M15-2 (RSSI) - Body ground Always 10 kΩ or higher
G53-6 (RDAS) or M15-5 (DATA) - Body ground Always 10 kΩ or higher
G53-15 (RCO) or M15-4 (+5) - Body ground Always 10 kΩ or higher




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR