DATA LIST
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| ACC SW | Power switch ACC signal/ON or OFF | ON: Power switch on (ACC)
OFF: Power switch off |
- |
| IG SW | Power switch IG signal/ON or OFF | ON: Power switch on (IG)
OFF: Power switch off |
- |
| RR Door Courtesy | Rear door courtesy light switch RH signal/CLOSE or OPEN | CLOSE: Rear door RH closed
OPEN: Rear door RH open |
- |
| RL Door Courtesy | Rear door courtesy light switch LH signal/CLOSE or OPEN | CLOSE: Rear door LH closed
OPEN: Rear door LH open |
- |
| FR Door Lock Pos | Front door RH unlock detection switch signal/LOCK or UNLOCK | LOCK: Front door RH locked
UNLOCK: Front door RH unlocked |
- |
| FR Door Courtesy | Front door courtesy light switch RH signal/CLOSE or OPEN | CLOSE: Front door RH closed
OPEN: Front door RH open |
- |
| FL Door Lock Pos | Front door LH unlock detection switch signal/LOCK or UNLOCK | LOCK: Front door LH locked
UNLOCK: Front door LH unlocked |
- |
| FL Door Courtesy | Front door courtesy light switch LH signal/CLOSE or OPEN | CLOSE: Front door LH closed
OPEN: Front door LH open |
- |
| RR-Door Lock Pos SW | Rear door RH and LH unlock detection switch signal/ON or OFF | ON: Rear door RH or LH unlocked
OFF: Rear door RH and LH locked |
- |
| RL-Door Lock Pos SW | Rear door RH and LH unlock detection switch signal/ON or OFF | ON: Rear door RH or LH unlocked
OFF: Rear door RH and LH locked |
- |
| Wireless Control | Wireless door lock control function/ON or OFF | Customization status displayed | - |
| Hazard Answer Back | Hazard answer-back of wireless/ON or OFF | Customization status displayed | - |
| Open Door Warning | Open door warning/ON or OFF | Customization status displayed | - |
| Auto Lock Time | Automatic lock time/120 s, 60 s or 30 s | Customization status displayed | - |
| Wireless Buzzer Resp | Buzzer answer-back of wireless/ON or OFF | Customization status displayed | - |
| Wireless Buzzer Vol | Wireless door lock buzzer volume/Level7, Level6, Level5, Level4, Level3, Level2, Level1 or Level0 | Customization status displayed | - |
ACTIVE TEST
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Active Test.
Perform the Active Test according to the display on the intelligent tester.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Illuminated Entry System | Interior lights (Interior light switch is in door position and all doors are closed) | OFF/ON | - |
| Door Lock | Door lock motor | Unlock/Lock | - |
| Trunk and Back-Door Open | Back door lock motor | OFF/ON | - |
| Wireless Buzzer | Wireless door lock buzzer | OFF/ON | - |