CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Disconnect the G77 and G79 certification ECU (smart key ECU assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| G77-11 (E) - Body ground | - | W-B - Body ground | Ground | Always | Below 1 Ω | - |
| G77-2 (+B) - G77-11 (E) | Input | B - W-B | +B power supply | Power switch off | 11 to 14 V | - |
| G77-10 (CUTB) - G77-11 (E) | Input | L - W-B | Dark current cut pin* | Power switch off | 11 to 14 V | - |
*: In order to prevent the vehicle auxiliary battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is set in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle auxiliary battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of electric waves every 0.25 seconds. that form the detection area stops).
If the result is not as specified, there may be a malfunction on the wire harness side or the fuse is removed.
Reconnect the G77 and G79 certification ECU (smart key ECU assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| G79-5 (IG) - G77-11 (E) | Input | V - W-B | IG power supply | Power switch off → on (IG) | Below 1 V → 11 to 14 V | Engine Switch |
| G79-12 (CLG1) - G77-11 (E) | Output | L - W-B | Output to driver door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area) |
Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Electrical key transmitter sub-assembly not inside vehicle 5.
Electrical key transmitter sub-assembly brought inside detection area*1 6.
All doors locked through wireless operation |
Pulse generation (See waveform 1) | Over Head + Driver Side (key diagnostic mode) |
| Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Electrical key transmitter sub-assembly not inside vehicle 5.
Electrical key transmitter sub-assembly brought outside detection area*2 6.
All doors locked through wireless operation |
Pulse generation (See waveform 2) | Over Head + Driver Side (key diagnostic mode) | ||||
| G79-13 (CG1B) - G77-11 (E) | Output | P - W-B | Output to driver door electrical key antenna (terminal on opposite side of component from CLG1 output terminal) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Electrical key transmitter sub-assembly not inside vehicle 5.
Electrical key transmitter sub-assembly brought outside detection area*2 6.
All doors locked through wireless operation |
Pulse generation (See waveform 2) | Over Head + Driver Side (key diagnostic mode) |
| G79-11 (CLG2) - G77-11 (E) | Output | L - W-B | Output to front passenger door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area) |
Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Electrical key transmitter sub-assembly not inside vehicle 5.
Electrical key transmitter sub-assembly brought inside detection area*1 6.
All doors locked through wireless operation |
Pulse generation (See waveform 1) | Over Head + Passenger Side (key diagnostic mode) |
| Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Electrical key transmitter sub-assembly not inside vehicle 5.
Electrical key transmitter sub-assembly brought outside detection area*2 6.
All doors locked through wireless operation |
Pulse generation (See waveform 2) | Over Head + Passenger Side (key diagnostic mode) | ||||
| G79-10 (CG2B) - G77-11 (E) | Output | P - W-B | Output to front passenger door electrical key antenna (terminal on opposite side of component from CLG2 output terminal) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Electrical key transmitter sub-assembly not inside vehicle 5.
Electrical key transmitter sub-assembly brought outside detection area*2 6.
All doors locked through wireless operation |
Pulse generation (See waveform 2) | Over Head + Passenger Side (key diagnostic mode) |
| G79-3 (CLG5) - G77-11 (E) | Output | P - W-B | Output to No. 1 indoor electrical key antenna assembly (front floor) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Door is open 4.
Door is closed 5.
Within 30 seconds |
Pulse generation (See waveform 3) | Over Head + Front Room (key diagnostic mode) |
| G79-2 (CG5B) - G77-11 (E) | Output | Y - W-B | Output to No. 1 indoor electrical key antenna assembly (front floor) (terminal on opposite side of component from CLG5 output terminal) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Door is open 4.
Door is closed 5.
Within 30 seconds |
Pulse generation (See waveform 3) | Over Head + Front Room (key diagnostic mode) |
| G79-20 (TSW1) - G77-11 (E) | Input | LG - W-B | Driver door lock sensor signal input
(Sends signal from door lock sensor on front door outside handle assembly to certification ECU (smart key ECU assembly). Certification ECU (smart key ECU assembly) send 12 V pulse waveform every 40 ms. from terminal TSW. When door lock sensor is touched, the pulse is grounded. |
Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Driver door lock sensor not touched → touched |
Pulse generation (See waveform 5) | D-Door Trigger Switch |
| G79-8 (TSW2) - G77-11 (E) | Input | LG - W-B | Front passenger door lock sensor signal input
(Sends signal from door lock sensor on front door outside handle assembly to certification ECU (smart key ECU assembly). Certification ECU (smart key ECU assembly) sends 12 V pulse waveform every 40 ms. from terminal TSW. When door lock sensor is touched, the pulse is grounded. |
Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Front passenger door lock sensor not touched → touched |
Pulse generation (See waveform 5) | P-Door Trigger Switch |
| G79-22 (SEN1) - G77-11 (E) | Input | BE - W-B | Driver door unlock sensor signal input
(when system is in unlock standby mode and touch sensor is touched, door electrical key antenna sends touch sensor input signal (sensing) to certification ECU (smart key ECU assembly)) |
Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors locked 4.
Electrical key transmitter sub-assembly not sufficiently close to vehicle 5.
Driver door unlock sensor not touched → touched |
Pulse generation (See waveform 5) | D-Door Touch Sensor |
| G79-23 (SEN2) - G77-11 (E) | Input | R - W-B | Front passenger door unlock sensor signal input
(when system is in unlock standby mode and touch sensor is touched, door electrical key antenna sends touch sensor input signal (sensing) to certification ECU (smart key ECU assembly)) |
Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors locked 4.
Electrical key transmitter sub-assembly not sufficiently close to vehicle 5.
Front passenger door unlock sensor not touched → touched |
Pulse generation (See waveform 5) | P-Door Touch Sensor |
| G78-27 (TSW5) - G77-11 (E) | Input | L - W-B | Back door opener switch assembly (unlock switch) signal input | Back door opener switch assembly (unlock switch) off → on | Pulse generation (See waveform 5) | Tr/B-Door Unlock SW |
| G78-28 (TSW6) - G77-11 (E) | Input | G - W-B | Back door opener switch assembly (lock switch) signal input | Back door opener switch assembly (lock switch )off → on | Pulse generation (See waveform 5) | Tr/B-Door Lock SW |
| G78-11 (CLG6) - G77-11 (E) | Output | LG - W-B | Output to No. 2 indoor electrical key antenna assembly (steering column) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Door is open 4.
Door is closed 5.
Within 30 seconds |
Pulse generation (See waveform 3) | Over Head + Rear Room (key diagnostic mode) |
| G78-10 (CG6B) - G77-11 (E) | Output | V*4 - W-B
SB*5 - W-B |
Output to No. 2 indoor electrical key antenna assembly (steering column) (terminal on opposite side of component from CLG6 output terminal) | Proceed:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Door is open 4.
Door is closed 5.
Within 30 seconds |
Pulse generation (See waveform 3) | Over Head + Rear Room (key diagnostic mode) |
| G78-9 (CLG7) - G77-11 (E) | Output | W - W-B | Output to No. 3 indoor electrical key antenna assembly (rear floor) | Proceed:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Door is open 4.
Door is closed 5.
Within 30 seconds |
Pulse generation (See waveform 3) | Over Head + Back Door (inside) (key diagnostic mode) |
| G78-8 (CG7B) - G77-11 (E) | Output | BR - W-B | Output to No. 3 indoor electrical key antenna assembly (rear floor) (terminal on opposite side of component from CLG7 output terminal) | Proceed:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Door is open 4.
Door is closed 5.
Within 30 seconds |
Pulse generation (See waveform 3) | Over Head + Back Door (inside) (key diagnostic mode) |
| G79-19 (POS1) - G77-11 (E) | Output | W - W-B | Driver door unlock sensor power source (12 V (drops when power switch turned on (IG))) | Power switch off → on (IG) | 9 to 14 V → Below 2 V | - |
| G79-21 (POS2) - G77-11 (E) | Output | GR - W-B | Front passenger door unlock sensor power source (12 V (drops when power switch turned on (IG))) | Power switch off → on (IG) | 9 to 14 V → Below 2 V | - |
| G78-5 (RCO) - G77-11 (E) | Output | L - W-B | Output to door control receiver
(Power supply for door control receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.) |
Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
Electrical key transmitter sub-assembly brought outside detection area*2 but kept inside wireless function operational area*3 4.
Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed |
Pulse generation (See waveform 6) | - |
| G78-17 (RDAS) - G77-11 (E) | Input | LG - W-B | Door control receiver verifies data received from electrical key transmitter sub-assembly. Door control receiver sends data to ECU and intermittently grounds 12 V signal from certification ECU (smart key ECU assembly). | Proceed:
1.
Power switch off 2.
All doors locked 3.
Electrical key transmitter sub-assembly brought outside detection area*2 but kept inside wireless function operational area*3 4.
Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed |
Pulse generation (See waveform 7) | - |
| G78-19 (RSSI) - G77-11 (E) | Output | R*4 - W-B
P*5 - W-B |
Door control receiver sends signal to certification ECU (smart key ECU assembly) indicating whether electric waves (example: 312 MHz) from key are being received or not (receiver grounds 12 V signal from certification ECU (smart key ECU assembly)) | Procedure:
1.
Power switch off 2.
All doors closed |
Below 1 V → 4.5 to 6 V → Below 1 V | Key diagnostic mode |
| G78-2 (CLG8) - G77-11 (E) | Output | V - W-B | Output to electrical key antenna (outside luggage) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Back door opener switch assembly off → on |
Pulse generation (See waveform 4) | Over Head + Back Door
or Luggage + Back Door (key diagnostic mode) |
| G78-1 (CG8B) - G77-11 (E) | Output | L - W-B | Output to electrical key antenna (outside luggage) (terminal on opposite side of component from CLG8 output terminal) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Back door opener switch assembly off → on |
Pulse generation (See waveform 4) | Over Head + Back Door
or Luggage + Back Door (key diagnostic mode) |
*1: For details about the areas that are inside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
*2: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
*3: For details about the areas that are inside the wireless function operational area, refer to Operation Check (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).
*4: for LHD
*5: for RHD
Using an oscilloscope, check waveform 1.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | G79-12 (CLG1) - G77-11 (E)
G79-11 (CLG2) - G77-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Electrical key transmitter sub-assembly not inside vehicle 5.
Electrical key transmitter sub-assembly brought inside detection area* 6.
All doors locked through wireless operation |
*: For details about the areas that are inside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
Using an oscilloscope, check waveform 2.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | G79-12 (CLG1) - G77-11 (E)
G79-11 (CLG2) - G77-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Electrical key transmitter sub-assembly not inside vehicle 5.
Electrical key transmitter sub-assembly brought outside detection area* 6.
All doors locked through wireless operation |
*: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
| Item | Content |
|---|---|
| Tester Connection | G79-13 (CG1B) - G77-11 (E)
G79-10 (CG2B) - G77-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Electrical key transmitter sub-assembly not inside vehicle 5.
Electrical key transmitter sub-assembly brought outside detection area* 6.
All doors locked through wireless operation |
*: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
Using an oscilloscope, check waveform 3.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| *a | Door open |
| *b | After approximately 30 seconds from when the door is closed |
| Item | Content |
|---|---|
| Tester Connection | G79-3 (CLG5) - G77-11 (E)
G79-2 (CG5B) - G77-11 (E) G78-11 (CLG6) - G77-11 (E) G78-10 (CG6B) - G77-11 (E) G78-9 (CLG7) - G77-11 (E) G78-8 (CG7B) - G77-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Door is open 4.
Door is closed 5.
Within 30 seconds |
Using an oscilloscope, check waveform 4.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| *a | Power switch off, all doors closed and back door opener switch assembly off → on |
| Item | Content |
|---|---|
| Tester Connection | G78-2 (CLG8) - G77-11 (E)
G78-1 (CG8B) - G77-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Back door opener switch assembly off → on |
Using an oscilloscope, check waveform 5.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| *a | In actuality, sampling is being performed |
| Item | Content |
|---|---|
| Tester Connection | G79-20 (TSW1) - G77-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Driver door lock sensor not touched → touched |
| Item | Content |
|---|---|
| Tester Connection | G79-8 (TSW2) - G77-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Front passenger door lock sensor not touched → touched |
| Item | Content |
|---|---|
| Tester Connection | G79-22 (SEN1) - G77-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV |
| Condition | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors locked 4.
Electrical key transmitter sub-assembly not sufficiently close to vehicle 5.
Driver door unlock sensor not touched → touched |
| Item | Content |
|---|---|
| Tester Connection | G79-23 (SEN2) - G77-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors locked 4.
Electrical key transmitter sub-assembly not sufficiently close to vehicle 5.
Front passenger door unlock sensor not touched → touched |
| Item | Content |
|---|---|
| Tester Connection | G78-27 (TSW5) - G77-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV |
| Condition | Back door opener switch assembly (unlock switch) off → on |
| Item | Content |
|---|---|
| Tester Connection | G78-28 (TSW6) - G77-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV |
| Condition | Back door opener switch assembly (lock switch) off → on |
Using an oscilloscope, check waveform 6.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| *a | Before lock or unlock button of electrical key transmitter sub-assembly pressed |
| *b | After lock or unlock button of electrical key transmitter sub-assembly pressed |
| Item | Content |
|---|---|
| Tester Connection | G78-5 (RCO) - G77-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2 4.
Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed |
*1: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
*2: For details about the areas that are inside the wireless function operational area, refer to Operation Check (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).
Using an oscilloscope, check waveform 7.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| *a | Before lock or unlock button of electrical key transmitter sub-assembly pressed |
| *b | After lock or unlock button of electrical key transmitter sub-assembly pressed |
| Item | Content |
|---|---|
| Tester Connection | G78-17 (RDAS) - G77-11 (E) |
| Tool Setting | 5 V/DIV., 500 ms/DIV. |
| Condition | Proceed:
1.
Power switch off 2.
All doors locked 3.
Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2 4.
Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed |
*1: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
*2: For details about the areas that are inside the wireless function operational area, refer to Operation Check (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).
CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *A | Main body ECU (multiplex network body ECU) with 1 connector | *B | for LHD |
| *C | for RHD | - | - |
| *1 | Main body ECU (multiplex network body ECU) | - | - |
| *A | Main body ECU (multiplex network body ECU) with 2 connectors | - | - |
| *1 | Main body ECU (multiplex network body ECU) | - | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| MB-11 (GND1) - Body ground | - | - | Ground | Always | Below 1 Ω | - |
| MB-30 (BECU) - Body ground | Input | - | Auxiliary battery power supply (for CPU) | Always | 11 to 14 V | - |
| MB-29 (ACC) - Body ground | Input | - | ACC power supply | Power switch on (ACC) | 11 to 14 V | ACC SW |
| MB-32 (IG) - Body ground | Input | - | Power switch power supply | Power switch on (IG) | 11 to 14 V | IG SW |
If the result is not as specified, there may be a malfunction in the wire harness.
Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| 3D-36 (FLCY) - Body ground | Input | R - Body ground | Front door LH courtesy light switch input | Front door LH open | Below 1 V | FL Door Courtesy |
| Front door LH closed | 11 to 14 V | |||||
| G59-19 (FRCY) - Body ground | Input | R - Body ground | Front door RH courtesy light switch input | Front door RH open | Below 1 V | FR Door Courtesy |
| Front door RH closed | 11 to 14 V | |||||
| G59-24 (LCTY) - Body ground | Input | L - Body ground | Rear door LH courtesy light switch input | Rear door LH open | Below 1 V | RL Door Courtesy SW |
| Rear door LH closed | Pulse generation (See waveform 3 or 4) | |||||
| G59-6 (RCTY) - Body ground | Input | G - Body ground | Rear door RH courtesy light switch input | Rear door RH open | Below 1 V | RR Door Courtesy SW |
| Rear door RH closed | Pulse generation (See waveform 1 or 2) | |||||
| 3D-35 (BCTY) - Body ground | Input | B - Body ground | Back door courtesy light switch input | Back door open | Below 1 V | Back Door Courtesy SW |
| Power switch off, all doors closed and back door closed | 11 to 14 V | |||||
| G59-11 (L2) - Body ground | Input | SB*1 - Body ground
B*2 - Body ground |
Driver door key-linked lock input | Driver door key cylinder in lock position | Below 1 V | Door Key SW-Lock |
| Power switch off, all doors closed and driver door key cylinder in neutral position | Pulse generation (See waveform 3 or 4) | |||||
| G59-12 (UL2) - Body ground | Input | LG*1, G*2 - Body ground | Driver door key-linked unlock input | Driver door key cylinder in unlock position | Below 1 V | D Door Key SW-UL |
| Power switch off, all doors closed and driver door key cylinder in neutral position | Pulse generation (See waveform 1 or 2) | |||||
| 3D-11 (ACT+) - Body ground | Output | GR - Body ground | Door lock motor lock drive output | Driver door control switch not pushed and driver door key cylinder in neutral position | Below 1 V | - |
| Lock side of driver door control switch pushed or driver door key cylinder in lock position | 11 to 14 V | |||||
| 3B-2 (ACT+) - Body ground | Output | V - Body ground | Door lock motor lock drive output | Driver door control switch not pushed and driver door key cylinder in neutral position | Below 1 V | - |
| Lock side of driver door control switch pushed or driver door key cylinder in lock position | 11 to 14 V | |||||
| 3B-1 (ACT+) - Body ground | Output | Y - Body ground | Door lock motor lock drive output | Driver door control switch not pushed and driver door key cylinder in neutral position | Below 1 V | - |
| Lock side of driver door control switch pushed or driver door key cylinder in lock position | 11 to 14 V | |||||
| 3D-12 (ACT+) - Body ground | Output | L - Body ground | Door lock motor lock drive output | Driver door control switch not pushed and driver door key cylinder in neutral position | Below 1 V | - |
| Lock side of driver door control switch pushed or driver door key cylinder in lock position | 11 to 14 V | |||||
| 3D-9 (TR+) - Body ground | Output | Y - Body ground | Driver door lock motor unlock drive output | Back door closed | Below 1 V | - |
| Back door open | 11 to 14 V | |||||
| 3D-8 (ACT-) - Body ground | Output | P - Body ground | Door lock motor unlock drive output | Driver door control switch not pushed and driver door key cylinder in neutral position | Below 1 V | - |
| Unlock side of driver door control switch pushed or driver door key cylinder in unlock position | 11 to 14 V | |||||
| 3D-7 (ACT-) - Body ground | Output | LG - Body ground | Door lock motor unlock drive output | Driver door control switch not pushed and driver door key cylinder in neutral position | Below 1 V | - |
| Unlock side of driver door control switch pushed or driver door key cylinder in unlock position | 11 to 14 V | |||||
| 3B-4 (ACT-) - Body ground | Output | L - Body ground | Door lock motor unlock drive output | Driver door control switch not pushed and driver door key cylinder in neutral position | Below 1 V | - |
| Unlock side of driver door control switch pushed or driver door key cylinder in unlock position | 11 to 14 V | |||||
| 3B-3 (ACT-) - Body ground | Output | R - Body ground | Door lock motor unlock drive output | Driver door control switch not pushed and driver door key cylinder in neutral position | Below 1 V | - |
| Unlock side of driver door control switch pushed or driver door key cylinder in unlock position | 11 to 14 V | |||||
| G59-7 (LSFL) - Body ground | Input | L - Body ground | Front door LH unlock detection switch input | Front door LH unlocked | Below 1 V | FL Door Lock Pos |
| Power switch off, all doors closed and front door LH locked | Pulse generation (See waveform 1 or 2) | |||||
| G59-18 (LSFR) - Body ground | Input | L - Body ground | Front door RH unlock detection switch input | Front door RH unlocked | Below 1 V | FR Door Lock Pos |
| Power switch off, all doors closed and front door RH locked | Pulse generation (See waveform 1 or 2) | |||||
| 3D-24 (LSR) - Body ground | Input | Y - Body ground | Rear door LH unlock detection switch input | Rear door LH or RH unlocked | Below 1 V | RL-Door Lock Pos SW |
| Power switch off, all doors closed and rear door LH and RH locked | Pulse generation (See waveform 3 or 4) | |||||
| 3D-25 (LSR) - Body ground | Input | V - Body ground | Rear door RH unlock detection switch input | Rear door RH or LH unlocked | Below 1 V | RR-Door Lock Pos SW |
| Power switch off, all doors closed and rear door RH and LH locked | Pulse generation (See waveform 3 or 4) |
*1: for LHD
*2: for RHD
If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.
Using an oscilloscope, check waveform 1.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | G59-6 (RCTY) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Rear door RH closed |
| Item | Content |
|---|---|
| Tester Connection | G59-12 (UL2) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Power switch off, all doors closed and driver door key cylinder in neutral position |
| Item | Content |
|---|---|
| Tester Connection | G59-7 (LSFL) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Power switch off, all doors closed and front door LH locked |
| Item | Content |
|---|---|
| Tester Connection | G59-18 (LSFR) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Power switch off, all doors closed and front door RH locked |
Using an oscilloscope, check waveform 2.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | G59-6 (RCTY) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Rear door RH closed |
| Item | Content |
|---|---|
| Tester Connection | G59-7 (LSFL) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Power switch off, all doors closed and front door LH locked |
| Item | Content |
|---|---|
| Tester Connection | G59-12 (UL2) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Power switch off, all doors closed and driver door key cylinder in neutral position |
| Item | Content |
|---|---|
| Tester Connection | G59-18 (LSFR) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Power switch off, all doors closed and front door RH locked |
Using an oscilloscope, check waveform 3.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | G59-11 (L2) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Power switch off, all doors closed and driver door key cylinder in neutral position |
| Item | Content |
|---|---|
| Tester Connection | G59-24 (LCTY) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Rear door LH closed |
| Item | Content |
|---|---|
| Tester Connection | 3D-24 (LSR) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Power switch off, all doors closed and rear door LH and RH locked |
| Item | Content |
|---|---|
| Tester Connection | 3D-25 (LSR) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Power switch off, all doors closed and rear door RH and LH locked |
Using an oscilloscope, check waveform 4.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | G59-11 (L2) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Power switch off, all doors closed and driver door key cylinder in neutral position |
| Item | Content |
|---|---|
| Tester Connection | G59-24 (LCTY) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Rear door LH closed |
| Item | Content |
|---|---|
| Tester Connection | 3D-24 (LSR) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Power switch off, all doors closed and rear door LH and RH locked |
| Item | Content |
|---|---|
| Tester Connection | 3D-25 (LSR) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Power switch off, all doors closed and rear door RH and LH locked |