Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Entry Function) › 2011.12–2013.12
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278080 SMART ENTRY AND START SYSTEM(for Entry Function) D

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  OPERATION CHECK  


CHECK SMART ENTRY AND START SYSTEM (for Entry Function) OPERATION


NOTICE:

Make sure that the smart entry and start system (for Entry Function) has not been canceled before performing this inspection.


a.

Check the entry unlock function (driver door, front passenger door).

i.

Perform a wireless lock operation to lock the door, touch the unlock sensor built into the backside of the front door outside handle assembly of the driver door while carrying the electrical key transmitter sub-assembly and check that the door unlocks.

HINT:

To perform a wireless lock operation, press the lock button of the electrical key transmitter sub-assembly while standing near the front door outside handle assembly.



ii.
B300377E02
2.354,1.167 2.563,1.354 0.208,0.188 10 false *a 1.26,3.479 1.469,3.667 0.208,0.188 10 false *a 0.125,0.083 0.542,0.49 0.417,0.406 10 true *A 0.177,2.302 0.75,2.458 0.573,0.156 10 false *B

Inspect the entry unlock detection area. Hold the electrical key transmitter sub-assembly at the same height as the front door outside handle assembly and approximately 0.7 m (2.30 ft.) from the vehicle as shown in the illustration and check that the LED (red) of the electrical key transmitter sub-assembly blinks.

Text in Illustration
*A for LHD
*B for RHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)


iii.

With the system in unlock standby mode, grasp the front door outside handle assembly and check that the door unlocks.

HINT:
·

The system is in unlock standby mode when the electrical key transmitter sub-assembly is in the detection area and the key ID code sent by the electrical key transmitter sub-assembly matches the key ID code stored by the certification ECU (smart key ECU assembly).

·

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the front door outside handle assembly.

·

Inspect the front passenger door using the same procedure.




iv.
B300387E01
0.082,0.153 0.352,0.361 0.270,0.208 10 *A 0.133,2.378 0.404,2.586 0.270,0.208 10 *B 2.327,2.121 2.597,2.329 0.270,0.208 10 *a 1.903,1.407 1.903,2.203 1.903,2.203 2.297,2.203 false 2.187,4.27 2.403,4.424 0.217,0.154 10 *a 1.749,3.756 1.749,4.351 1.749,4.351 2.142,4.351 false

Check the unlock response sensitivity. With the system in unlock standby mode, touch the area shown in the illustration and check that the door unlocks.

NOTICE:

If the sensor is touched too quickly or released too slowly, the sensor may not react and the door will not unlock.


Text in Illustration
*A for LHD
*B for RHD
*a Unlock Sensor (Backside)



b.
B300388E01
0.15,0.156 0.421,0.364 0.270,0.208 10 *A 0.202,2.498 0.472,2.706 0.270,0.208 10 *B 1.679,2.186 1.950,2.394 0.270,0.208 10 *a 1.256,1.648 1.256,2.28 1.256,2.28 1.649,2.28 false 2.636,4.314 2.853,4.469 0.217,0.154 10 *a 2.198,3.859 2.198,4.4 2.198,4.4 2.592,4.4 false

Check the entry lock function (driver door, front passenger door).

NOTICE:

If the electrical key transmitter sub-assembly is in the vehicle but outside the detection area (on the instrument panel, in the glove box, on the floor) and a door lock operation is performed, the key lock-in prevention function will not operate and the electrical key transmitter sub-assembly will be locked inside the vehicle.


Text in Illustration
*A for LHD
*B for RHD
*a Lock Sensor

i.

With the door closed and unlocked, touch the lock sensor of the front door outside handle assembly of the driver door while carrying the electrical key transmitter sub-assembly and check that the door locks.

HINT:

If the door does not lock even when touching the lock sensor, touch it with your palm.



ii.
B300377E02
2.354,1.167 2.563,1.354 0.208,0.188 10 false *a 1.26,3.479 1.469,3.667 0.208,0.188 10 false *a 0.125,0.083 0.542,0.49 0.417,0.406 10 true *A 0.177,2.302 0.75,2.458 0.573,0.156 10 false *B

Inspect the entry lock operating range. Hold the electrical key transmitter sub-assembly approximately 0.1 m (0.328 ft.) below the bottom edge of the door glass and approximately 0.3 m (0.984 ft.) from the vehicle as shown in the illustration, touch the lock sensor and check that the door locks.

Text in Illustration
*A for LHD
*B for RHD
*a Approximately 0.3 m (0.984 ft.)

HINT:
·

If the door does not lock even when touching the lock sensor, touch it with your palm.

·

As communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the front door outside handle assembly, the door may not lock if the lock sensor is touched with the same hand that is carrying the electrical key transmitter sub-assembly, etc.

·

If the key lock-in prevention function buzzer sounds, electric waves from the indoor electrical key antenna may be leaking from the vehicle.

·

Inspect the front passenger door using the same procedure.

·

The door lock operation cannot be performed more than 3 times consecutively.





c.

Check the entry luggage compartment open function.

i.
B296515E01
1.785,1.283 2.022,1.453 0.237,0.170 10 *a 1.525,2.657 1.525,2.981 1.525,2.981 1.717,2.981 false 1.75,2.899 1.987,3.068 0.237,0.170 10 *1

Perform a wireless lock operation to lock the doors, operate the unlock switch of the luggage door opening switch assembly while carrying the electrical key transmitter sub-assembly and check that the door unlocks.

Text in Illustration
*1 Unlock Switch
*a Approximately 0.7 m (2.30 ft.)


ii.

Inspect the entry back door unlock operating range. While standing at the rear of the vehicle, hold the electrical key transmitter sub-assembly so that it is facing the direction shown in the illustration at the same height as the back door opener switch assembly and approximately 0.7 m (2.30 ft.) from the vehicle, press the unlock switch of the back door opener switch assembly and check that the door unlock.



d.

Check the entry back door lock function.

NOTICE:

If the electrical key transmitter sub-assembly is inside the vehicle and a door lock operation is performed, it is possible that the electrical key transmitter sub-assembly may be locked inside the vehicle.


i.

With the door closed and unlocked, press the lock switch of the back door opener switch assembly while carrying the electrical key transmitter sub-assembly outside of the vehicle and check that the door lock.


ii.
B296516E02
1.796,1.287 2.024,1.504 0.229,0.218 10 *a 2.223,2.904 2.502,3.069 0.279,0.165 10 *1 1.958,2.61 1.958,2.98 1.958,2.98 2.17,2.98 false

Inspect the entry back door lock operating range. Hold the electrical key transmitter sub-assembly so that it is facing the direction shown in the illustration at the same height as the top edge of the rear bumper and approximately 0.3 m (0.984 ft.) from the vehicle, press the lock of the back door opener switch assembly and check that the door lock.

Text in Illustration
*1 Lock Switch
*a Approximately 0.3 m (.0.984 ft.)

HINT:
·

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the rear bumper.

·

If the key lock-in prevention function buzzer sounds, electric waves from the indoor electrical key antenna assembly may be leaking from the vehicle.





e.

Check the push start function.

i.

With the power switch off, move the shift lever to P, depress the brake pedal while carrying the electrical key transmitter sub-assembly. Then, press the power switch and check that the hybrid system starts.


ii.

With the brake pedal released and the power switch off, press the power switch while carrying the electrical key transmitter sub-assembly and check that the power source mode changes as follows: off → on (ACC) → on (IG) → off.


iii.

Stop the vehicle, press the power switch and check that the power source mode changes to off (the hybrid system stops and all electrical systems are off).


iv.
B300410E02
0.938,1.156 2.354,1.865 2.354,1.865 2.531,1.865 false 1.646,3.438 2.385,4.094 2.385,4.094 2.563,4.094 false 2.573,1.771 2.802,1.99 0.229,0.219 10 false *a 0.094,0.083 0.375,0.25 0.281,0.167 10 false *A 0.094,2.323 0.375,2.49 0.281,0.167 10 false *B 2.604,4.01 2.833,4.229 0.229,0.219 10 false *a

Inspect the push start operating range (steering column). Place the electrical key transmitter sub-assembly on the steering column at inspection point so that it is facing in the direction shown in the illustration and check that the hybrid system can be started.

Text in Illustration
*A for LHD
*B for RHD
*a Inspection Point

NOTICE:
·

Even if the electrical key transmitter sub-assembly is within the vehicle interior detection area, the electrical key transmitter sub-assembly may not be properly detected if it is on the instrument panel, in the glove box or on the floor.

·

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the shift lever.




v.
B296517E01
2.524,0.398 2.772,0.567 0.248,0.170 10 *a 1.75,1.219 2.33,0.481 2.33,0.481 2.491,0.481 false

Inspect the push start operating range (front floor). Place the electrical key transmitter sub-assembly on the front seat at either inspection point so that it is facing in the direction shown in the illustration and check that the hybrid system can be started.

Text in Illustration
*a Inspection Point

NOTICE:
·

Even if the electrical key transmitter sub-assembly is within the vehicle interior detection area, the electrical key transmitter sub-assembly may not be properly detected if it is on the instrument panel, in the glove box or on the floor.

·

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the shift lever.



HINT:

Perform the inspection for both inspection points.



vi.
B296518E01
2.456,0.23 2.704,0.400 0.248,0.170 10 *a 1.809,0.68 2.29,0.325 2.29,0.325 2.423,0.325 false

Inspect the push start operating range (rear floor). Place the electrical key transmitter sub-assembly on the rear seat at either inspection point so that it is facing in the direction shown in the illustration and check that the hybrid system can be started.

Text in Illustration
*a Inspection Point

NOTICE:
·

Even if the electrical key transmitter sub-assembly is within the vehicle interior detection area, the electrical key transmitter sub-assembly may not be properly detected if it is on the instrument panel, in the glove box or on the floor.

·

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the rear seat cushion.



HINT:

Perform the inspection for both inspection points.




f.

Check the key lock-in prevention function (vehicle interior).

NOTICE:

In order to prevent the electrical key transmitter sub-assembly from being locked inside the vehicle, perform this inspection with the window of a door open.


i.

Turn the power switch off.


ii.

Place the electrical key transmitter sub-assembly on a front or rear seat.


iii.

Close the door, making sure the doors are unlocked.


iv.

Touch a door lock sensor and check that the doors do not lock and the key lock-in prevention function buzzer (external) sounds for approximately 5 seconds.



g.

Check the entry cancel function.

i.

Cancel the smart entry and start system and check that all the functions of the smart entry and start system (for Entry Function) no longer operate.

HINT:
·

Refer to the following procedures to cancel the smart entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>CUSTOMIZE PARAMETERS).

·

While the smart entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly near the power switch.




ii.

While the key cancel function (entry cancel function) is on, check that all functions of the smart entry and start system cannot be operated.



h.

Check the answer-back function (hazard warning light flashing and buzzer sounding).

Entry Operation Wireless Buzzer Hazard Warning Light
Entry Door Lock Sounds once Flashes once
Entry Door Unlock Sounds twice Flashes twice
Entry Back Door Lock Sounds once Flashes once
Entry Back Door Unlock Sounds twice Flashes twice



KEY DIAGNOSTIC MODE (Using Intelligent Tester)


HINT:

With key diagnostic mode, it is possible to check if the electrical key transmitter sub-assembly is operating properly with the selected electrical key antenna and within the selected detection area by the sounding of the wireless buzzer.


a.

Enter the following menus: Body / Entry&Start / Utility / Communication Check (Key Diag Mode).


b.

Inspect the appropriate item according to the following table.

Tester Display Inspection Item
Overhead + Driver Side*1 Front door outside handle assembly (electrical key antenna) [for Driver Side]
Overhead + Passenger Side*2 Front door outside handle assembly (electrical key antenna) [for Front Passenger Side]
Overhead + Front Room*3 No. 1 indoor electrical key antenna assembly (front floor)
Overhead + Rear Room*4 No. 2 indoor electrical key antenna assembly (steering column)
Overhead + Back Door*5 Electrical key antenna (outside luggage)
Luggage + Back Door (inside)*6 No. 3 indoor electrical key antenna assembly (rear floor)
Luggage + Luggage*7 Electrical key antenna (outside luggage)
Immobiliser Amp*8 Amplifier (power switch)


c.

Bring the electrical key transmitter sub-assembly near the selected electrical key antenna and check that the wireless door lock buzzer sounds.

HINT:

The buzzer sounds in short, repeated beeps for all items except "Overhead + Rear Room"*4. For "Overhead + Rear Room"*4, the buzzer sounds in one long, continuous beep.


i.
B300377E02
2.354,1.167 2.563,1.354 0.208,0.188 10 false *a 1.26,3.479 1.469,3.667 0.208,0.188 10 false *a 0.125,0.083 0.542,0.49 0.417,0.406 10 true *A 0.177,2.302 0.75,2.458 0.573,0.156 10 false *B

*1: Front door outside handle assembly (for Driver Side)

Text in Illustration
*A for LHD
*B for RHD
*a Approximately 0.3 m (0.984 ft.)

HINT:
·

Hold the electrical key transmitter sub-assembly at the same height as the front door outside handle assembly in the position shown in the illustration.

·

*2: Perform the same inspection for the front passenger side.





d.
B296517E01
2.524,0.398 2.772,0.567 0.248,0.170 10 *a 1.75,1.219 2.33,0.481 2.33,0.481 2.491,0.481 false

*3: No. 1 indoor electrical key antenna assembly (front floor)

Text in Illustration
*a Inspection Point

HINT:

Place the electrical key transmitter sub-assembly on the front seat cushion of the driver seat or front passenger seat.



e.
B300410E02
0.938,1.156 2.354,1.865 2.354,1.865 2.531,1.865 false 1.646,3.438 2.385,4.094 2.385,4.094 2.563,4.094 false 2.573,1.771 2.802,1.99 0.229,0.219 10 false *a 0.094,0.083 0.375,0.25 0.281,0.167 10 false *A 0.094,2.323 0.375,2.49 0.281,0.167 10 false *B 2.604,4.01 2.833,4.229 0.229,0.219 10 false *a

*4: No. 2 indoor electrical key antenna assembly (steering column)

Text in Illustration
*A for LHD
*B for RHD
*a Inspection Point

HINT:

Place the electrical key transmitter sub-assembly on the steering column.



f.
B296538E01
1.792,1.318 2.041,1.488 0.248,0.170 10 *a

*5, *7: Electrical key antenna (outside luggage)

Text in Illustration
*a Approximately 0.7 m (2.30 ft.)

HINT:

Hold the electrical key transmitter sub-assembly at the same height as the rear bumper upper surface and align it with the center of the rear of the vehicle, as shown in the illustration.



g.
B296518E01
2.456,0.23 2.704,0.400 0.248,0.170 10 *a 1.809,0.68 2.29,0.325 2.29,0.325 2.423,0.325 false

*6: No. 3 indoor electrical key antenna (rear floor)

Text in Illustration
*a Inspection Point

HINT:

Place the electrical key transmitter sub-assembly in the luggage compartment. Even if the electrical key transmitter sub-assembly is in the luggage compartment, the buzzer may not sound.



h.
B296539

*8: Amplifier (power switch)

HINT:

While facing the logo side of the electrical transmitter sub-assembly towards the power switch, hold the transmitter near the power switch.