If the entry unlock function does not operate for the back door only, but the entry lock function operates, the request code is being transmitted properly from the back door. In this case, there may be a problem related to the unlock switch (connection between the back door opener switch assembly and certification ECU (smart key ECU assembly)).
The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the intelligent tester with the power switch off to troubleshoot:
Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).
After repair, confirm DTC not reoccur with performing the "DTC Output Confirmation Operation".
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Entry&Start / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| B-Dr Opening Operation | Back door opening operation / Long, Twice, OFF | Customization status displayed | - |
| Result | Proceed to |
|---|---|
| Customize setting is Long or Twice. | A |
| Customize setting is OFF. | B |
A
B
When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).
Door locks operate normally.
OK
NG
Enter the following menus: Body Electrical / Main Body / Active Test.
Perform the Active Test according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Trunk and Back-Door Open | Operate back door lock motor | ON or OFF | - |
The back door lock assembly unlatches when ON is selected.
OK
NG
Using the intelligent tester, read the Data List (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Tr/B Door Unlock SW | Back door opener switch (unlock switch) / ON or OFF | ON: Back door opener switch (unlock switch) pushed
OFF: Back door opener switch (unlock switch) not pushed |
·
Displays whether the back door opener switch (unlock switch) is on or off. ·
Use this Data List item to help determine if there is a switch malfunction when the back door unlock function does not operate. |
The intelligent tester display changes correctly in response to the operation of the back door opener switch assembly.
OK
NG
Disconnect the T6 back door opener switch assembly connector.
Disconnect the G53 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T6-3 (B) - G53-22 (TSW5) | Always | Below 1 Ω |
| T6-2 (L) - Body ground | Always | Below 1 Ω |
| T6-3 (B) or G53-22 (TSW5) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the back door opener switch assembly (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3 (B) - 2 (L) | No switch pushed | 10 kΩ or higher |
| 3 (B) - 2 (L) | Unlock switch pushed | Below 1 Ω |
| *a | Component without harness connected
(Back Door Opener Switch Assembly) |
OK
NG