If the entry lock and unlock functions do not operate for the back door only, the request code may not be being transmitted from the back door. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and electrical key antenna [outside luggage]), or there may be electric wave interference.
The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the intelligent tester with the power switch off to troubleshoot:
Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).
After repair, confirm DTC not reoccur with performing the "DTC Output Confirmation Operation".
When the entry lock and unlock functions do not operate for doors other than the driver door and if the power switch has not been turned on (IG) for 14 days or more, lock/unlock the doors using the wireless door lock function or key linked unlock operation and then check if the entry door lock and unlock functions operate.
When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).
Door locks operate normally.
OK
NG
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Entry&Start / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Tr/B-Door Lock SW | Back door opener switch assembly (lock switch) / ON or OFF | ON: Back door opener switch assembly (lock switch) pushed
OFF: Back door opener switch assembly (lock switch) not pushed |
·
Displays whether the back door opener switch assembly (lock switch) is on or off. ·
Use this Data List item to help determine if there is a switch malfunction when the back door lock function does not operate. |
| Tr/B-Door Unlock SW | Back door opener switch assembly (unlock switch) / ON or OFF | ON: Back door opener switch assembly (unlock switch) pushed
OFF: Back door opener switch assembly (unlock switch) not pushed |
·
Displays whether the back door opener switch assembly (unlock switch) is on or off. ·
Use this Data List item to help determine if there is a switch malfunction when the back door unlock function does not operate. |
On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.
OK
NG
Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the electrical key antenna (outside luggage) and perform an entry back door unlock function check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
| *a | Approximately 0.3 m (0.984 ft.) |
If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the rear bumper, communication may not possible.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of electric wave interference is high. Also, added vehicle components may cause electric wave interference. If installed, remove them and perform the operation check.
Entry function operates normally.
OK
NG
Check the following antenna in the key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
Check the electrical key antenna (outside luggage).
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage), check that the wireless door lock buzzer sounds.
Wireless door lock buzzer sounds.
OK
NG
Disconnect the M19 electrical key antenna (outside luggage) connector.
Disconnect the G78 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M19-1 (ANTE8) - G78-2 (CLG8) | Always | Below 1 Ω |
| M19-2 (CLGB) - G78-1 (CG8B) | Always | Below 1 Ω |
| M19-1 (ANTE8) or G78-2 (CLG8) - Body ground | Always | 10 kΩ or higher |
| M19-2 (CLGB) or G78-1 (CG8B) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the electrical key antenna (outside luggage) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Outside Luggage Compartment)>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (ANTE8) - 2 (CLGB) | Always | Below 1 Ω |
| *a | Component without harness connected
(Electrical Key Antenna (Outside Luggage)) |
OK
NG
Disconnect the back door opener switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T6-2 (L) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to Back Door Opener Switch Assembly) |
OK
NG