Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Entry Function) › from 2015.11
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278080 SMART ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  Back Door Entry Lock and Unlock Functions do not Operate  


DESCRIPTION

If the entry lock and unlock functions do not operate for the back door only, the request code may not be being transmitted from the back door. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and electrical key antenna [outside luggage]), or there may be electric wave interference.

WIRING DIAGRAM

B300367E16
5.688,0.427 6.229,0.698 0.542,0.271 10 false G78 0.521,1.448 3.229,1.833 2.708,0.385 10 false Electrical Key Antenna (Outside Luggage) 0.531,1.281 0.875,1.583 0.344,0.302 10 false M19 6.073,0.906 6.573,1.135 0.5,0.229 10 false CG8B 6.073,0.448 6.5,0.646 0.427,0.198 10 false CLG8 1.875,0.438 2.406,0.594 0.531,0.156 10 false ANTE8 1.948,0.885 2.365,1.042 0.417,0.156 10 false CLGB 5.771,0.698 5.948,0.854 0.177,0.156 10 false 1 5.781,0.24 5.958,0.396 0.177,0.156 10 false 2 2.438,0.323 2.729,0.542 0.292,0.219 10 false 1 2.448,0.771 2.646,1 0.198,0.229 10 false 2 6.073,2.396 6.677,2.677 0.604,0.281 10 false TSW6 5.74,2.208 5.917,2.385 0.177,0.177 10 false 28 6.073,2.896 6.667,3.188 0.594,0.292 10 false TSW5 5.74,2.698 5.917,2.875 0.177,0.177 10 false 27 5.542,3.458 7.073,3.865 1.531,0.406 10 false Certification ECU (Smart Key ECU Assembly) 0.958,3.302 1.323,3.479 0.365,0.177 10 false T6 0.948,3.458 3.292,3.698 2.344,0.24 10 false Back Door Opener Switch Assembly 2.385,2.302 2.635,2.479 0.25,0.177 10 false UL 1.615,2.542 2.563,2.802 0.948,0.26 10 false Lock Switch 1.531,3.021 2.823,3.354 1.292,0.333 10 false Unlock Switch 2.677,2.302 2.854,2.479 0.177,0.177 10 false 1 2.458,2.781 3.135,3.073 0.677,0.292 10 false B 1.271,2.781 1.479,2.958 0.208,0.177 10 false L 2.688,2.781 2.865,2.958 0.177,0.177 10 false 3 1.042,2.781 1.219,2.958 0.177,0.177 10 false 2 5.688,2.885 6.177,3.219 0.49,0.333 10 false G78 5.688,2.396 6.052,2.583 0.365,0.188 10 false G78 5.688,0.896 6.073,1.146 0.385,0.25 10 false G78

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the intelligent tester with the power switch off to troubleshoot:

Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

After repair, confirm DTC not reoccur with performing the "DTC Output Confirmation Operation".

·

When the entry lock and unlock functions do not operate for doors other than the driver door and if the power switch has not been turned on (IG) for 14 days or more, lock/unlock the doors using the wireless door lock function or key linked unlock operation and then check if the entry door lock and unlock functions operate.



PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Door locks operate normally.




OK

2.READ VALUE USING INTELLIGENT TESTER (BACK DOOR OPENER SWITCH)

NG

GO TO POWER DOOR LOCK CONTROL SYSTEM

2.READ VALUE USING INTELLIGENT TESTER (BACK DOOR OPENER SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Entry&Start / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Tr/B-Door Lock SW Back door opener switch assembly (lock switch) / ON or OFF ON: Back door opener switch assembly (lock switch) pushed
OFF: Back door opener switch assembly (lock switch) not pushed
·

Displays whether the back door opener switch assembly (lock switch) is on or off.

·

Use this Data List item to help determine if there is a switch malfunction when the back door lock function does not operate.


Tr/B-Door Unlock SW Back door opener switch assembly (unlock switch) / ON or OFF ON: Back door opener switch assembly (unlock switch) pushed
OFF: Back door opener switch assembly (unlock switch) not pushed
·

Displays whether the back door opener switch assembly (unlock switch) is on or off.

·

Use this Data List item to help determine if there is a switch malfunction when the back door unlock function does not operate.



OK:

On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.




OK

3.CHECK WAVE ENVIRONMENT

NG

7.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH - BODY GROUND)
3.CHECK WAVE ENVIRONMENT
a.
B431435E02
1.802,1.323 2.156,1.552 0.354,0.229 10 false *a

Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the electrical key antenna (outside luggage) and perform an entry back door unlock function check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

Text in Illustration
*a Approximately 0.3 m (0.984 ft.)

NOTICE:

If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the rear bumper, communication may not possible.


HINT:

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of electric wave interference is high. Also, added vehicle components may cause electric wave interference. If installed, remove them and perform the operation check.


OK:

Entry function operates normally.




OK

AFFECTED BY WAVE INTERFERENCE

NG

4.CHECK ELECTRICAL KEY ANTENNA IN KEY DIAGNOSTIC MODE
4.CHECK ELECTRICAL KEY ANTENNA IN KEY DIAGNOSTIC MODE
a.

Check the following antenna in the key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

HINT:

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter cannot be detected by channel 2 due to a malfunction, such as wave interference.


i.
B431435E02
1.802,1.323 2.156,1.552 0.354,0.229 10 false *a

Check the electrical key antenna (outside luggage).

Text in Illustration
*a 0.7 to 1 m (2.30 to 3.28 ft.)

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage), check that the wireless door lock buzzer sounds.

OK:

Wireless door lock buzzer sounds.





OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)
5.CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)
a.

Disconnect the M19 electrical key antenna (outside luggage) connector.


b.

Disconnect the G78 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M19-1 (ANTE8) - G78-2 (CLG8) Always Below 1 Ω
M19-2 (CLGB) - G78-1 (CG8B) Always Below 1 Ω
M19-1 (ANTE8) or G78-2 (CLG8) - Body ground Always 10 kΩ or higher
M19-2 (CLGB) or G78-1 (CG8B) - Body ground Always 10 kΩ or higher




OK

6.INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)
a.
B226391E25
1.827,1.07 2.223,0.709 2.223,0.709 2.409,0.709 false 1.588,1.07 1.192,0.709 1.192,0.709 1.006,0.709 false 2.454,0.617 2.879,0.791 0.424,0.174 10 CLGB 0.412,0.617 0.900,0.791 0.488,0.174 10 ANTE8 0.183,0.179 0.342,0.353 0.160,0.174 10 *a

Remove the electrical key antenna (outside luggage) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Outside Luggage Compartment)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ANTE8) - 2 (CLGB) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Electrical Key Antenna (Outside Luggage))



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

7.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH - BODY GROUND)
a.
U183354E01
0.103,0.071 0.273,0.211 0.170,0.140 10 *a 1.977,1.793 2.124,1.962 0.148,0.170 12 L 1.716,1.36 1.716,1.896 1.716,1.896 1.954,1.896 false 1.611,0.152 1.819,0.293 0.208,0.141 10 T6

Disconnect the back door opener switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
T6-2 (L) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Back Door Opener Switch Assembly)


OK

REPLACE BACK DOOR OPENER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR