Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Entry Function) › from 2015.11
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278080 SMART ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  B27A6  Open in Rear Floor Electrical Key Oscillator Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 2 indoor electrical key antenna assembly (steering column). For the No. 2 indoor electrical key antenna assembly (steering column) to detect when the electrical key transmitter sub-assembly is inside the vehicle, the signal from the certification ECU (smart key ECU assembly) requesting a response from the electrical key transmitter sub-assembly is transmitted inside the vehicle. DTC B27A6 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (steering column) (between terminals CLG6 and ANTE6, or terminals CG6B and CLGB).

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B27A6 An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (steering column) (CLG6 - ANTE6, CG6B - CLGB) (1 trip detection logic*).
·

Wire harness or connector

·

No. 2 indoor electrical key antenna assembly (steering column)

·

Certification ECU (smart key ECU assembly)


Any time

*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
When electrical key transmitter sub-assembly is on the steering column:
·

Power source mode does not change when power switch pressed

·

Electrical key transmitter sub-assembly locked inside vehicle


-

Related Data List and Active Test
DTC Code Data List and Active Test
B27A6 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B349035E41
1.125,0.448 1.896,0.646 0.771,0.198 10 false ANTE6 1.188,0.906 1.958,1.104 0.771,0.198 10 false CLGB 1.667,0.333 1.906,0.635 0.24,0.302 10 false 1 1.677,0.792 1.917,1.094 0.24,0.302 10 false 3 0.115,1.396 0.573,1.594 0.458,0.198 10 false G52 0.125,1.563 2.323,1.938 2.198,0.375 10 false No. 2 Indoor Electrical Key Antenna Assembly (Steering Column) 5.271,0.906 5.583,1.104 0.313,0.198 10 false G78 5.271,0.448 5.667,0.646 0.396,0.198 10 false G78 5.271,1.365 5.583,1.563 0.313,0.198 10 false G77 5.292,1.823 6.823,2.396 1.531,0.573 10 false Certification ECU (Smart Key ECU Assembly) 5.333,0.26 5.49,0.458 0.156,0.198 10 false 11 5.323,0.729 5.479,0.927 0.156,0.198 10 false 10 5.333,1.188 5.677,1.448 0.344,0.26 10 false 11 5.625,0.448 6.24,0.646 0.615,0.198 10 false CLG6 5.625,0.896 6.24,1.094 0.615,0.198 10 false CG6B 5.625,1.365 5.938,1.563 0.313,0.198 10 false E

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the intelligent tester with the power switch off to troubleshoot:

Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The No. 2 indoor electrical key antenna assembly (steering column) has an antenna coil between ANTE6 and CLGB terminals.



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the power switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (steering column).

OK:

Connectors are properly connected.




OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 2 INDOOR ELECTRICAL KEY ANTENNA)

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 2 INDOOR ELECTRICAL KEY ANTENNA)
a.

Disconnect the G78 and G77 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the G52 No. 2 indoor electrical key antenna assembly (steering column) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G78-11 (CLG6) - G52-1 (ANTE6) Always Below 1 Ω
G78-10 (CG6B) - G52-3 (CLGB) Always Below 1 Ω
G77-11 (E) - Body ground Always Below 1 Ω
G78-11 (CLG6) or G52-1 (ANTE6) - Body ground Always 10 kΩ or higher
G78-10 (CG6B) or G52-3 (CLGB) - Body ground Always 10 kΩ or higher




OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA)
a.

Connect the G78 and G77 certification ECU (smart key ECU assembly) connectors.

U183391E02
3.625,1.385 3.979,2.188 false 3.438,1.385 3.083,2.188 false 2.708,1.521 2.438,2.198 false 1.208,2.771 1.417,2.969 0.208,0.198 10 false *1 0.177,0.063 0.385,0.26 0.208,0.198 10 false *a 1.594,4.354 1.802,4.552 0.208,0.198 10 false *b 2.917,2.198 3.333,2.396 0.417,0.198 10 false CLG6 3.427,0.531 3.75,0.729 0.323,0.198 10 false G78 2.333,4.354 2.542,4.552 0.208,0.198 10 false *c 3.802,2.198 4.219,2.396 0.417,0.198 10 false CG6B 0.99,3.625 1.406,3.823 0.417,0.198 10 false GND 2.365,2.219 2.531,2.417 0.167,0.198 10 false E 2.188,0.521 2.5,0.719 0.313,0.198 10 false G77

Text in Illustration
*1 Waveform - -
*a Component with harness connected
(Certification ECU (smart key ECU assembly))
*b Within approximately 30 seconds from when the door is closed
*c After approximately 30 seconds from when the door is closed - -


b.

Connect the G52 No. 2 indoor electrical key antenna assembly (steering column) connector.


c.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Switch Condition Tool Setting Specified Condition
G78-11 (CLG6) - G77-11 (E) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)
G78-10 (CG6B) - G77-11 (E) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)




OK

4.REPLACE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (STEERING COLUMN)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (STEERING COLUMN)
a.

Temporarily replace the No. 2 indoor electrical key antenna assembly (steering column) with a new or known good one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Driver Side)>REMOVAL).



NEXT

5.CLEAR DTC
6.CHECK FOR DTC

OK

END (NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (STEERING COLUMN) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)