The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the electrical key antenna (outside luggage). For the electrical key antenna (outside luggage) to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, the received request signal is transmitted within approximately 1.0 m (3.28 ft.) of the back door. DTC B27A8 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage) (between terminals CLG8 and ANTE8, or terminals CG8B and CLGB).
| DTC Code | DTC Detection Condition | Trouble Area | DTC Output Confirmation Operation |
|---|---|---|---|
| B27A8 | An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage) (CLG8 - ANTE8, CG8B - CLGB) (1 trip detection logic*). | ·
Wire harness or connector ·
Electrical key antenna (outside luggage) ·
Certification ECU (smart key ECU assembly) |
Any time |
*: Only output while a malfunction is present.
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
| Entry lock or unlock operation cannot be performed for luggage compartment door | - |
| DTC Code | Data List and Active Test |
|---|---|
| B27A8 | Key diagnostic mode can be used to perform troubleshooting |
The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the intelligent tester with the power switch off to troubleshoot:
Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).
After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
The electrical key antenna (outside luggage) has an antenna coil between ANTE8 and CLGB terminals.
Turn the power switch off.
Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage).
Connectors are properly connected.
OK
NG
Disconnect the G53 and G55 certification ECU (smart key ECU assembly) connectors.
Disconnect the M19 electrical key antenna (outside luggage) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G53-2 (CLG8) - M19-1 (ANTE8) | Always | Below 1 Ω |
| G53-1 (CG8B) - M19-2 (CLGB) | Always | Below 1 Ω |
| G53-2 (CLG8) or M19-1 (ANTE8) - Body ground | Always | 10 kΩ or higher |
| G53-1 (CG8B) or M19-2 (CLGB) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the electrical key antenna (outside luggage) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Outside Luggage Compartment)>REMOVAL).
| *a | Component without harness connected
(Electrical Key Antenna (Outside Luggage)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (ANTE8) - 2 (CLGB) | Always | Below 1 Ω |
OK
NG
Temporarily replace the certification ECU (smart key ECU assembly) with a new one.
Refer to the Service Bulletin.
NEXT
NEXT
Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>DTC CHECK / CLEAR).
DTC B27A8 is not output.
OK
NG