Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Entry Function) › from 2015.11
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278080 SMART ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  B27A8  Open in Outside Luggage Compartment Electrical Key Antenna Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the electrical key antenna (outside luggage). For the electrical key antenna (outside luggage) to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, the received request signal is transmitted within approximately 1.0 m (3.28 ft.) of the back door. DTC B27A8 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage) (between terminals CLG8 and ANTE8, or terminals CG8B and CLGB).

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B27A8 An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage) (CLG8 - ANTE8, CG8B - CLGB) (1 trip detection logic*).
·

Wire harness or connector

·

Electrical key antenna (outside luggage)

·

Certification ECU (smart key ECU assembly)


Any time

*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Entry lock or unlock operation cannot be performed for luggage compartment door -

Related Data List and Active Test
DTC Code Data List and Active Test
B27A8 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B349035E43
1.125,0.448 1.896,0.646 0.771,0.198 10 false ANTE8 1.188,0.906 1.958,1.104 0.771,0.198 10 false CLGB 1.667,0.333 1.906,0.635 0.24,0.302 10 false 1 1.677,0.792 1.917,1.094 0.24,0.302 10 false 2 0.177,1.375 0.635,1.573 0.458,0.198 10 false M19 0.177,1.552 2.156,2.031 1.979,0.479 10 false Electrical Key Antenna (Outside Luggage) 5.271,0.448 5.583,0.646 0.313,0.198 10 false G78 5.417,1.833 6.958,2.417 1.542,0.583 10 false Certification ECU (Smart Key ECU Assembly) 5.365,0.26 5.521,0.458 0.156,0.198 10 false 2 5.365,0.729 5.521,0.927 0.156,0.198 10 false 1 5.333,1.188 5.677,1.448 0.344,0.26 10 false 11 5.625,0.448 6.24,0.646 0.615,0.198 10 false CLG8 5.625,0.906 6.24,1.104 0.615,0.198 10 false CG8B 5.625,1.365 5.938,1.563 0.313,0.198 10 false E 5.271,0.906 5.583,1.104 0.313,0.198 10 false G78 5.271,1.365 5.583,1.563 0.313,0.198 10 false G77

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the intelligent tester with the power switch off to troubleshoot:

Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The electrical key antenna (outside luggage) has an antenna coil between ANTE8 and CLGB terminals.



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the power switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage).

OK:

Connectors are properly connected.




OK

2.CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)
a.

Disconnect the G78 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the M19 electrical key antenna (outside luggage) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G78-2 (CLG8) - M19-1 (ANTE8) Always Below 1 Ω
G78-1 (CG8B) - M19-2 (CLGB) Always Below 1 Ω
G78-2 (CLG8) or M19-1 (ANTE8) - Body ground Always 10 kΩ or higher
G78-1 (CG8B) or M19-2 (CLGB) - Body ground Always 10 kΩ or higher




OK

3.INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)
a.
B226391E24
1.827,1.07 2.223,0.709 2.223,0.709 2.409,0.709 false 1.588,1.07 1.192,0.709 1.192,0.709 1.006,0.709 false 2.44,0.617 2.864,0.791 0.424,0.174 10 CLGB 0.41,0.617 0.940,0.791 0.530,0.174 10 ANTE8 0.183,0.179 0.342,0.353 0.160,0.174 10 *a

Remove the electrical key antenna (outside luggage) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Outside Luggage Compartment)>REMOVAL).

Text in Illustration
*a Component without harness connected
(Electrical Key Antenna (Outside Luggage))


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ANTE8) - 2 (CLGB) Always Below 1 Ω




OK

4.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

4.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Temporarily replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to the Service Bulletin.




NEXT

5.CLEAR DTC
6.CHECK FOR DTC

OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG