Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › from 2014.12
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278081 SMART ENTRY AND START SYSTEM(for Start Function) U

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  TERMINALS OF ECU  


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


U183372E02
1.896,0.688 2.208,0.854 0.313,0.167 10 false G77 3.323,0.688 3.615,0.854 0.292,0.167 10 false G78 4.865,0.677 5.167,0.844 0.302,0.167 10 false G79

a.

Disconnect the G77 and G79 connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
G77-2 (+B) - Body ground Input B - Body ground Power source Power switch off 11 to 14 V -
G77-9 (IG2D) - Body ground Output P - Body ground IG2 signal 20°C (68°F) Approximately 302.97 Ω IG2 Relay Monitor(Outside)
G77-11 (E) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G77-18 (STP1) - Body ground Input G - Body ground Stop light switch signal Brake pedal released → Brake pedal depressed 1 V or less → 9 V or higher Stop Light Switch1
G79-4 (ACCD) - Body ground Output L - Body ground ACC signal 20°C (68°F) 81.49 to 118.98 Ω ACC Relay Monitor
G79-6 (IG1D) - Body ground Output SB - Body ground IG1 signal 20°C (68°F) 40.74 to 59.49 Ω IG1 Relay Monitor(Outside)
G79-25 (P) - G77-11 (E) Input G - W-B P position signal Shift lever in P → Shift lever not in P 40 kΩ or higher → 200 Ω or less Shift P Signal
G79-26 (SLP) - Body ground Input P - Body ground Steering lock position signal Steering wheel locked 10 kΩ or higher Steering Unlock Switch
G79-27 (SPD) - G77-11 (E) Input SB - W-B Vehicle speed signal Always 30 kΩ or higher Vehicle Speed Signal
G79-28 (SSW1) - Body ground Input V - Body ground SSW1 contact signal Power switch pushed → Power switch not pushed Below 1 Ω → 10 kΩ or higher Start Switch1
G79-30 (SSW2) - Body ground Input SB - Body ground SSW2 contact signal
HINT:

Backup for SSW1. Behaves the same way as SSW1.


Power switch pushed → Power switch not pushed Below 1 Ω → 10 kΩ or higher Start Switch2


c.

Reconnect the G77 and G79 connectors.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
G77-9 (IG2D) - G77-11 (E) Output P - W-B IG2 signal Power switch on (ACC) → Power switch on (IG) 1 V or less → 9 V or higher IG2 Relay Monitor(Outside)
G79-4 (ACCD) - G77-11 (E) Output L - W-B ACC signal Power switch off → Power switch on (ACC) 1 V or less → 8.5 V or higher ACC Relay Monitor
G79-6 (IG1D) - G77-11 (E) Output SB - W-B IG1 signal Power switch on (ACC) → Power switch on (IG) 1 V or less → 9 V or higher IG1 Relay Monitor(Outside)
G79-25 (P) - G77-11 (E) Input G - W-B P position signal Shift lever in P → Shift lever not in P 9 V or higher → 1.5 V or less Shift P Signal
G79-26 (SLP) - G77-11 (E) Input P - W-B Steering lock position signal Steering wheel locked → Steering wheel unlocked*1 11 to 14 V → 1.2 V or less Steering Unlock Switch
G79-27 (SPD) - G77-11 (E) Input SB - W-B Vehicle speed signal Vehicle being driven at approx. 5 km/h (3 mph) Pulse generation
(See waveform 2)
Vehicle Speed Signal
G79-28 (SSW1) - G77-11 (E) Input V - W-B SSW1 contact signal Power switch not pushed → Power switch pushed 9 V or higher → 1 V or less Start Switch1
G79-29 (SLR+) - G77-11 (E) Output L - W-B Steering lock motor operation command signal (Steering lock motor operation permission signal sent from the certification ECU (smart key ECU assembly)) Steering lock motor stopped → Steering lock motor operating → Steering lock motor stopped*2 Pulse generation (See waveform 1) -
G79-30 (SSW2) - G77-11 (E) Input SB - W-B SSW2 contact signal
HINT:

Backup for SSW1. Behaves the same way as SSW1.


Power switch not pushed → Power switch pushed 9 V or higher → 1 V or less Start Switch2

HINT:
·

*1: When the power switch is turned off with the shift lever in P and any of the doors are opened or closed, the steering wheel will be locked. When the power switch is turned on (ACC) or on (IG), the steering wheel will be unlocked.

·

*2: Perform the following procedure to operate the steering lock motor.

-

The shift lever is in P.

-

The power switch is off.

-

While carrying the electrical key transmitter sub-assembly, the power switch is turned on (IG) and the steering is unlocked.





e.

Using an oscilloscope, check the waveform of the ECU.

i.
U113990E03
1.708,1.708 1.792,1.99 1.792,1.99 1.844,1.99 false 1.531,0.438 2.646,0.198 2.646,0.198 2.719,0.198 false 2.646,0.208 2.448,0.458 false 2.906,1.583 3.25,1.865 0.344,0.281 10 false GND 1.917,1.917 2.406,2.063 0.49,0.146 10 false *b 2.76,0.104 3.125,0.333 0.365,0.229 10 false *a

Waveform 1

Item Content
Tester Connection G79-29 (SLR+) - G77-11 (E)
Tool Setting 2 V/DIV., 200 ms./DIV.
Vehicle Condition Steering lock motor stopped →
Steering lock motor operating →
Steering lock motor stopped

Text in Illustration
*a Steering lock motor not operating
*b Steering lock motor operating

HINT:

When all of the following conditions are met, open any of the doors to operate the steering lock motor.

·

The shift lever is in P.

·

While carrying the electrical key transmitter sub-assembly, the power switch is turned on (IG) and the steering is unlocked.

·

The power switch is off.




ii.
B220145E01
2.875,1.164 3.227,1.332 0.352,0.168 10 GND

Waveform 2

Item Content
Tester Connection G79-27 (SPD) - G77-11 (E)
Tool Setting 5 V/DIV., 20 ms./DIV.
Vehicle Condition Power switch on (IG), vehicle being driven at approx. 5 km/h (3 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.





HYBRID VEHICLE CONTROL ECU


U183483E02
5.51,1.49 5.823,1.646 0.313,0.156 10 false G81 4.219,1.49 4.531,1.646 0.313,0.156 10 false G80 2.792,1.49 3.063,1.646 0.271,0.156 10 false A72 1.469,1.49 1.74,1.646 0.271,0.156 10 false A71

a.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
G81-23 (IMO) - G80-6 (E1) Output BE - BR ID code box communication output
(Signal output from hybrid vehicle control ECU to ID code box)
Power switch off 11 to 14 V -
Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected Pulse generation
(See waveform 1)
G81-22 (IMI) - G80-6 (E1) Input LG - BR ID code box communication input
(Signal input from ID code box to hybrid vehicle control ECU)
Power switch off 11 to 14 V
Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected Pulse generation
(See waveform 2)

i.

Waveform 1

B443942E01
0.698,1.26 1.156,1.458 0.458,0.198 10 false GND 2.719,1.354 3.177,1.552 0.458,0.198 10 false *a 2.906,1.354 3.365,1.552 0.458,0.198 10 false *b

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Measurement Condition
Item Content
Tester Connection G81-23 (IMO) - G80-6 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Vehicle Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected


ii.

Waveform 2

B443943E01
0.729,1.25 1.188,1.448 0.458,0.198 10 false GND 3.115,1.354 3.573,1.552 0.458,0.198 10 false *a 3.313,1.354 3.771,1.552 0.458,0.198 10 false *b

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Measurement Condition
Item Content
Tester Connection G81-22 (IMI) - G80-6 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Vehicle Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected