Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › 2011.12–2013.12
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278081 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  U0293  Lost Communication with HV ECU  


DESCRIPTION

This DTC is stored when the power management control ECU detects a CAN communication error inside the power management control ECU (power control section - HV control section).

HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
U0293 CAN communication error inside the power management control ECU (power control section - HV control section). (1-trip detection logic*)
·

AM2 fuse

·

Power management control ECU

·

Wire harness or connector


Turn the power switch on (IG) and wait 10 seconds or more.

*: Only detected while a malfunction is present.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
There is no effect on vehicle behavior. -

WIRING DIAGRAM

B300415E02
1.171,3.421 2.868,3.560 1.698,0.139 10 : CAN Communication Line 2.503,2.078 2.783,2.217 0.280,0.139 10 G58 2.503,1.651 2.783,1.790 0.280,0.139 10 G58 1.363,0.924 1.672,1.064 0.309,0.139 10 AM2 0.163,0.764 1.024,1.070 0.861,0.306 10 from Auxiliary Battery 2.563,1.897 2.737,2.036 0.174,0.139 10 25 2.563,1.47 2.737,1.609 0.174,0.139 10 24 2.877,1.981 3.270,2.120 0.393,0.139 10 CA1H 3.435,3.126 5.548,3.282 2.113,0.156 10 Power Management Control ECU 2.877,1.556 3.260,1.695 0.382,0.139 10 CA1L 5.726,0.785 5.993,0.924 0.267,0.139 10 E01 5.726,1.204 5.993,1.343 0.267,0.139 10 E02 5.806,1.644 5.993,1.783 0.187,0.139 10 E1 3.893,1.707 5.304,1.855 1.411,0.148 10 Power Control Section 4.028,2.37 5.231,2.537 1.203,0.167 10 HV Control Section 6.165,0.599 6.276,0.745 0.111,0.145 10 5 6.082,0.786 6.366,0.976 0.284,0.191 10 G57 6.172,1.013 6.283,1.158 0.111,0.145 10 5 6.082,1.204 6.366,1.395 0.284,0.191 10 G58 6.163,1.452 6.274,1.597 0.111,0.145 10 6 6.082,1.638 6.366,1.829 0.284,0.191 10 G57 2.874,0.793 3.315,0.942 0.441,0.149 10 AM21 2.594,0.597 2.705,0.743 0.111,0.145 10 7 2.503,0.793 2.787,0.984 0.284,0.191 10 G58 2.874,1.204 3.315,1.353 0.441,0.149 10 AM22 2.594,1.017 2.705,1.163 0.111,0.145 10 1 2.503,1.204 2.787,1.394 0.284,0.191 10 G57

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body / Power Source Control / DTC.

for Entry&Start: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the power management control ECU, refer to the Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
U0293 - -


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)

OK

3.CHECK FOR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK FOR DTC

b.

Check for DTCs again.

OK:

DTC U0293 is not output




OK

NG