Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › 2013.12–2014.12
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278081 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B2271  Ignition Hold Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the IG1 circuit, IG2 circuit or IG hold circuit in the power management control ECU is detected.

HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2271 When either of the following conditions is met (1-trip detection logic*):
·

The IG1 or IG2 circuit in the power management control ECU is malfunctioning.

·

The IG hold circuit in the power management control ECU is malfunctioning.


·

AM2 fuse

·

Power management control ECU

·

Wire harness or connector


Turn the power switch on (IG).
HINT:

To turn the power switch on (IG), carry the electrical key transmitter sub-assembly and press the power switch twice with the shift lever in P and the brake pedal released.



*: Only detected while a malfunction is present and the power switch is on (IG)


HINT:
·

The IG1 and IG2 circuits activate the IG1 and IG2 relays.

·

After the IG1 and IG2 circuits turn on, even if the CPU operates incorrectly, the IG hold circuit maintains the power source mode in on (IG).



Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The power switch cannot be turned on (IG) (the hybrid control system cannot be started). The power source mode cannot be changed to on (IG).

WIRING DIAGRAM

B309715E01
4.964,6.67 5.217,6.826 0.253,0.156 10 IG2 4.493,7.037 6.279,7.235 1.786,0.199 10 No. 1 Integration Relay 2.707,1.059 3.054,1.208 0.347,0.149 10 IG1D 2.712,6.359 3.058,6.508 0.347,0.149 10 IG2D 0.287,7.094 0.995,7.243 0.708,0.149 10 *1: for LHD 0.287,7.444 1.037,7.593 0.750,0.149 10 *2: for RHD 3.716,5.103 6.384,5.252 2.669,0.149 10 Instrument Panel Junction Block Assembly 2.036,6.893 3.302,7.257 1.266,0.364 10 Power Management Control ECU 4.743,4.541 5.437,4.690 0.694,0.149 10 IG1 NO. 3 4.743,2.966 5.437,3.115 0.694,0.149 10 IG1 NO. 2 4.743,1.379 5.437,1.528 0.694,0.149 10 IG1 NO. 1 3.187,6.172 3.297,6.318 0.111,0.145 10 2 3.225,0.879 3.335,1.024 0.111,0.145 10 2 3.116,1.059 3.446,1.250 0.330,0.191 10 G58 3.117,6.354 3.447,6.545 0.330,0.191 10 A39 4.256,6.351 4.558,6.507 0.302,0.156 10 2D 5.981,6.355 6.263,6.511 0.282,0.156 10 2D 4.303,6.18 4.486,6.336 0.184,0.156 10 3 6.024,6.179 6.208,6.335 0.184,0.156 10 2 3.676,0.643 3.931,0.834 0.254,0.191 10 3E 3.678,1.059 3.933,1.250 0.254,0.191 10 3A 3.693,0.885 3.898,1.030 0.205,0.145 10 29 6.294,0.648 6.548,0.839 0.254,0.191 10 3A 6.305,0.474 6.542,0.619 0.237,0.145 10 54 6.299,2.229 6.553,2.419 0.254,0.191 10 3A 6.349,2.055 6.554,2.200 0.205,0.145 10 9 6.294,4.222 6.548,4.413 0.254,0.191 10 3B 6.337,4.048 6.541,4.193 0.205,0.145 10 8 5.753,2.369 6.262,2.524 0.509,0.155 10 WIPER 5.745,0.793 6.289,1.136 0.544,0.343 10 ECU-IG NO. 1 3.651,0.459 3.879,0.604 0.227,0.145 10 1*1 3.999,0.643 4.253,0.834 0.254,0.191 10 3F 3.974,0.459 4.204,0.604 0.231,0.145 10 1*2 0.087,1.581 0.991,2.055 0.904,0.473 10 from Auxiliary Battery 1.234,1.745 1.564,1.936 0.330,0.191 10 AM2 2.29,1.59 2.730,1.739 0.441,0.149 10 AM21 2.009,1.411 2.120,1.557 0.111,0.145 10 7 1.926,1.59 2.211,1.780 0.285,0.191 10 G58 2.29,1.99 2.730,2.139 0.441,0.149 10 AM22 2.009,1.804 2.120,1.949 0.111,0.145 10 1 1.926,1.99 2.212,2.180 0.286,0.191 10 G57 2.29,3.988 2.730,4.137 0.441,0.149 10 E01 2.021,3.811 2.132,3.956 0.111,0.145 10 5 1.926,3.988 2.212,4.179 0.286,0.191 10 G57 2.297,4.388 2.737,4.537 0.441,0.149 10 E02 2.028,4.21 2.139,4.356 0.111,0.145 10 5 1.926,4.388 2.212,4.578 0.286,0.191 10 G58 2.276,4.866 2.716,5.015 0.441,0.149 10 E1 2.019,4.679 2.130,4.825 0.111,0.145 10 6 1.926,4.866 2.212,5.056 0.286,0.191 10 G57 5.552,6.068 5.806,6.224 0.253,0.156 10 IG2 4.251,5.925 4.552,6.081 0.302,0.156 10 2D 4.301,5.762 4.484,5.918 0.184,0.156 10 4 5.981,5.936 6.282,6.092 0.302,0.156 10 2E 6.031,5.761 6.214,5.917 0.184,0.156 10 1

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body / Power Source Control / DTC.

for Entry&Start: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the power management control ECU, refer to the Service Bulletin.

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2271
Power Source Control
·

IG1 Relay Monitor (Inside)

·

IG2 Relay Monitor (Inside)

·

Latch Circuit


-


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
U183356E02
2.208,3.5 2.677,3.5 false 1.281,1.156 0.885,0.75 false 0.49,1.292 0.896,1.521 0.406,0.229 10 false G57 0.552,3.635 0.958,3.854 0.406,0.219 10 false G58 0.458,0.615 1,0.875 0.542,0.26 10 false AM22 2.708,3.427 3.083,3.563 0.375,0.135 10 false AM21 0.135,0.073 0.417,0.354 0.281,0.281 10 false *a

a.

Disconnect the G57 and G58 connectors from the power management control ECU.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G57-1 (AM22) - Body ground Power switch off 11 to 14 V
G58-7 (AM21) - Body ground Power switch off 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Power Management Control ECU)



OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)
U183357E02
2.271,1.188 2.74,1.188 false 2.104,1.156 2.75,0.625 false 1.906,3.49 2.75,3.385 false 0.5,1.271 1.073,1.625 0.573,0.354 10 false G57 0.49,3.563 0.958,3.813 0.469,0.25 10 false G58 2.781,0.469 3.115,0.688 0.333,0.219 10 false E01 2.781,1.104 3.042,1.302 0.26,0.198 10 false E1 2.781,3.292 3.167,3.552 0.385,0.26 10 false E02 0.177,0.052 0.323,0.188 0.146,0.135 10 false *a

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G57-5 (E01) - Body ground Always Below 1 Ω
G57-6 (E1) - Body ground Always Below 1 Ω
G58-5 (E02) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Power Management Control ECU)



OK

3.CHECK POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK POWER MANAGEMENT CONTROL ECU
a.
U183359E02
1.594,1.125 1.49,1.885 false 2.719,1.896 2.771,1.125 false 0.052,0.052 0.208,0.188 0.156,0.135 10 false *a 1.292,0.448 1.552,0.583 0.26,0.135 10 false A39 2.521,0.448 2.802,0.583 0.281,0.135 10 false G58 1.292,1.896 1.646,2.031 0.354,0.135 10 false IG2D 2.531,1.896 2.885,2.031 0.354,0.135 10 false IG1D

Reconnect the G58 power management control ECU connector.

Text in Illustration
*a Component with harness connected
(to Power Management Control ECU)


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-2 (IG2D) - Body ground Power switch on (ACC) → Power switch on (IG) 1 V or less → 9 V or higher
G58-2 (IG1D) - Body ground Power switch on (ACC) → Power switch on (IG) 1 V or less → 9 V or higher




OK

NG