Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › from 2015.11
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278081 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B2271  Ignition Hold Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the IG1 circuit, IG2 circuit or IG hold circuit of the certification ECU (smart key ECU assembly) is detected.

HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2271 When either of the following conditions is met (1-trip detection logic*):
·

The IG1 or IG2 circuit of the certification ECU (smart key ECU assembly) is malfunctioning.

·

The IG hold circuit of the certification ECU (smart key ECU assembly) is malfunctioning.


·

AM2 fuse

·

Certification ECU (Smart key ECU assembly)

·

Wire harness or connector


Turn the power switch on (IG).
HINT:

To turn the power switch on (IG), carry the electrical key transmitter sub-assembly and press the power switch twice with the shift lever in P and the brake pedal released.



*: Only detected while a malfunction is present and the power switch is on (IG)


HINT:
·

The IG1 and IG2 circuits activate the IG1 and IG2 relays.

·

After the IG1 and IG2 circuits turn on, even if the CPU operates incorrectly, the IG hold circuit maintains the power source mode in on (IG).



Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The power switch cannot be turned on (IG) (the hybrid control system cannot be started). The power source mode cannot be changed to on (IG).

WIRING DIAGRAM

B399050E01
4.985,5.802 5.238,5.958 0.253,0.156 10 IG2 4.372,6.168 6.157,6.367 1.786,0.199 10 No. 1 Integration Relay 2.702,1.48 3.049,1.628 0.347,0.149 10 IG1D 2.691,5.497 3.037,5.646 0.347,0.149 10 IG2D 0.28,7.04 0.988,7.189 0.708,0.149 10 *1: for LHD 0.28,7.419 1.030,7.568 0.750,0.149 10 *2: for RHD 3.758,4.234 6.426,4.383 2.669,0.149 10 Instrument Panel Junction Block Assembly 1.763,6.053 3.407,6.605 1.644,0.553 10 Certification ECU (Smart Key ECU Assembly) 4.738,3.387 5.432,3.536 0.694,0.149 10 IG1 NO. 2 4.738,1.8 5.432,1.949 0.694,0.149 10 IG1 NO. 1 3.166,5.31 3.276,5.456 0.111,0.145 10 9 3.22,1.299 3.331,1.445 0.111,0.145 10 6 3.112,1.48 3.441,1.670 0.330,0.191 10 G79 3.101,5.492 3.430,5.683 0.330,0.191 10 G77 3.674,5.483 3.976,5.639 0.302,0.156 10 2D 6.303,5.493 6.585,5.649 0.282,0.156 10 2D 3.721,5.311 3.905,5.467 0.184,0.156 10 3 6.346,5.317 6.530,5.473 0.184,0.156 10 2 3.672,1.064 3.926,1.255 0.254,0.191 10 3E 3.674,1.48 3.928,1.670 0.254,0.191 10 3A 3.689,1.306 3.894,1.451 0.205,0.145 10 29 6.289,1.069 6.544,1.259 0.254,0.191 10 3A 6.301,0.895 6.538,1.040 0.237,0.145 10 54 6.294,2.649 6.548,2.840 0.254,0.191 10 3A 6.345,2.475 6.549,2.621 0.205,0.145 10 9 6.294,3.07 6.548,3.260 0.254,0.191 10 3B 6.345,2.895 6.549,3.041 0.205,0.145 10 8 5.748,2.79 6.258,2.945 0.509,0.155 10 WIPER 5.74,1.213 6.284,1.557 0.544,0.343 10 ECU-IG NO. 1 3.647,0.879 3.874,1.025 0.227,0.145 10 1*1 3.994,1.064 4.248,1.255 0.254,0.191 10 3F 3.969,0.879 4.200,1.025 0.231,0.145 10 1*2 0.561,2.494 1.465,2.968 0.904,0.473 10 from Auxiliary Battery 1.227,2.159 1.557,2.349 0.330,0.191 10 AM2 2.283,2.002 2.726,2.152 0.443,0.150 10 +B 2.002,1.825 2.113,1.970 0.111,0.145 10 2 1.919,2.003 2.204,2.194 0.285,0.191 10 G77 2.284,4.004 2.724,4.153 0.441,0.149 10 E 1.998,3.818 2.173,3.963 0.176,0.145 10 11 1.926,3.992 2.249,4.183 0.324,0.191 10 G77 5.707,5.206 5.960,5.362 0.253,0.156 10 IG2 3.669,5.056 3.971,5.212 0.302,0.156 10 2D 3.719,4.893 3.903,5.049 0.184,0.156 10 4 6.303,5.075 6.605,5.230 0.302,0.156 10 2E 6.353,4.9 6.537,5.056 0.184,0.156 10 1

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body / Power Source Control / DTC.

for Entry&Start: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2271
Power Source Control
·

IG1 Relay Monitor (Inside)

·

IG2 Relay Monitor (Inside)

·

Latch Circuit


-


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
U183382E01
0.091,0.052 0.277,0.213 0.186,0.161 10 *a 0.32,1.362 0.615,1.518 0.295,0.156 10 G77 1.312,1.357 1.1,1.9 false 0.948,1.916 1.146,2.062 0.198,0.146 10 +B

a.

Disconnect the G77 connector from the certification ECU (smart key ECU assembly).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G77-2 (+B) - Body ground Power switch off 11 to 14 V


Text in Illustration
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))



OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)
U183383E01
0.091,0.052 0.277,0.213 0.186,0.161 10 *a 0.32,1.362 0.615,1.518 0.295,0.156 10 G77 2.327,1.931 2.525,2.076 0.198,0.146 10 E 2.048,1.587 2.305,1.989 false

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G77-11 (E) - Body ground Always Below 1 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the G77 certification ECU (smart key ECU assembly) connector.

U183378E01
0.302,0.29 0.488,0.451 0.186,0.161 10 *a 4.799,0.934 5.094,1.090 0.295,0.156 10 G79 2.175,0.932 2.470,1.088 0.295,0.156 10 G77 4.388,1.629 4.13,2.287 false 1.978,1.736 1.762,2.287 false 3.927,2.312 4.290,2.468 0.363,0.156 10 IG1D 1.531,2.313 1.893,2.469 0.363,0.156 10 IG2D

Text in Illustration
*a Component with harness connected
(to Certification ECU (Smart Key ECU Assembly))


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G77-9 (IG2D) - Body ground Power switch on (ACC) → Power switch on (IG) 1 V or less → 9 V or higher
G79-6 (IG1D) - Body ground Power switch on (ACC) → Power switch on (IG) 1 V or less → 9 V or higher




OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)