Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › from 2014.12
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278081 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B2275  STSW Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction is detected in the circuit between terminal ST2 of the certification ECU (smart key ECU assembly) and terminal ST2 of the hybrid vehicle control ECU.

HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2275 Certification ECU (smart key ECU assembly) internal HV activation request output circuit malfunction (1-trip detection logic*)
·

AM2 fuse

·

Steering lock system

·

Certification ECU (Smart key ECU assembly)

·

Wire harness or connector


Turn the power switch on (IG) and wait 10 seconds or more, then start the hybrid control system 3 times.

*: Only detected while a malfunction is present.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

The power source mode changes to on (READY) even though the hybrid control system is not started.

·

The power source mode does not change to on (READY) even though the hybrid control system is started.


-

WIRING DIAGRAM

B397999E11
0.365,2.802 0.76,3.01 0.396,0.208 10 false G80 0.354,2.969 2.229,3.365 1.875,0.396 10 false Hybrid Vehicle Control ECU 1.25,1.646 1.646,1.854 0.396,0.208 10 false ST2 1.635,1.531 2.031,1.74 0.396,0.208 10 false 9 1.979,0.698 3.375,0.906 1.396,0.208 10 false from Auxiliary Battery 4.094,0.875 4.51,1.083 0.417,0.208 10 false AM2 5.083,0.604 5.479,0.813 0.396,0.208 10 false 2 5.281,0.719 5.677,0.927 0.396,0.208 10 false +B 5.281,1.667 5.677,1.875 0.396,0.208 10 false ST2 5.104,1.521 5.5,1.729 0.396,0.208 10 false 7 5.281,2.365 5.677,2.573 0.396,0.208 10 false E 5.021,2.25 5.417,2.458 0.396,0.208 10 false 11 4.885,2.792 5.281,3 0.396,0.208 10 false G77 4.885,2.958 6.479,3.344 1.594,0.385 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body / Power Source Control / DTC.

for Entry&Start: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2275
Power Source Control
·

Starter Request Signal


-


PROCEDURE

1.CHECK FOR DTC

b.

Turn the power switch on (IG).


c.

After 25 seconds have elapsed, check if the DTC has been set again.

OK:

DTC B2285 is not output.




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

3.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

3.CHECK HARNESS AND CONNECTOR (GROUND)

OK

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the G85 the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G58 hybrid vehicle control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G58-9 (ST2) - G58-7 (ST2) Always Below 1 Ω
G58-9 (ST2) or G58-7 (ST2) - Body ground Always 10 kΩ or higher




OK

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the G85 certification ECU (smart key ECU assembly) connector.


b.

Reconnect the G58 hybrid vehicle control ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G77-7 (ST2) - G85 - 11 (E) Brake pedal depressed, power switch pressed for approx. 3 sec. → power switch released 9 V Higher→ Below 1 V




OK

REPLACE HYBRID VEHICLE CONTROL ECU

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)