DTC B2282 is stored when the vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication do not match.
DTC B2283 is stored when a malfunction in the vehicle speed sensor is detected.
When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
| DTC Code | DTC Detection Condition | Trouble Area | DTC Output Confirmation Operation |
|---|---|---|---|
| B2282 | The vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication (1-trip detection logic*) do not match. | ·
AM2 fuse ·
Meter/gauge system ·
Certification ECU (Smart key ECU assembly) ·
Junction Connector ·
Wire harness or connector |
Drive the vehicle for 20 seconds at a vehicle speed of 25 km/h (16 mph) or more, and then drive the vehicle at a vehicle speed of less than 5 km/h (3 mph) for 20 seconds. |
| B2283 | Vehicle speed signal malfunction detection : Excessive deceleration is detected (1-trip detection logic*) | ·
AM2 fuse ·
Meter/gauge system ·
Certification ECU (Smart key ECU assembly) ·
Junction Connector ·
Wire harness or connector |
Drive the vehicle for 30 seconds or more at a vehicle speed of 50 km/h (31 mph) or more. |
*: Only detected while a malfunction is present and the power switch is on (IG)
| DTC Code | Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|---|
| B2282 | ·
When the signal from the direct line or CAN communication is malfunctioning and indicates that the vehicle speed is 0 km/h (0 mph), there is no effect on vehicle behavior. ·
When the signal from the direct line or CAN communication is malfunctioning and indicates that the vehicle is moving, the power switch cannot be turned from on (IG) to off. |
- |
| B2283 | ·
The power source mode is changed to off (the hybrid control system is stopped) by pressing the power switch while the vehicle is being driven. ·
With the electrical key transmitter sub-assembly in the cabin, even if a hybrid control system start operation is performed, the hybrid control system does not start. |
Steering lock operation is prohibited. |
A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter. The signal is changed to a pulse signal at the transistor in the combination meter. Each ECU controls the respective system based on the pulse signal.
If a short occurs in an ECU, all systems in the diagram above will not operate normally.
When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:
for Power Source Control: Body / Power Source Control / DTC.
for Entry&Start: Body / Entry&Start / DTC.
The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.
| DTC | Data List Item | Active Test Item |
|---|---|---|
| B2282
B2283 |
Power Source Control
·
Vehicle Speed Signal ·
Engine Condition ·
Power Supply Condition Combination Meter
·
Vehicle Speed Meter |
- |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Combination Meter / Data List.
Check the Data List for proper functioning of the vehicle speed signal.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Vehicle Speed Meter | Vehicle speed/Min.: 0, Max.: 255 | Almost same as actual vehicle speed (Speedometer tester) | - |
Vehicle speed displayed on the intelligent tester is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
OK
NG
Enter the following menus: Body / Power Source Control / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Vehicle speed signal | Vehicle being driven or stopped/Stop or Run | Stop: Vehicle stopped
Run: Vehicle being driven at 5 km/h (3 mph) or more |
- |
Stop (vehicle is stopped) and Run (vehicle is running) appear on the screen.
OK
NG
OK
NG
OK
NG
Disconnect the G79 connector from the certification ECU (smart key ECU assembly).
Disconnect the G1 connector from the combination meter assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G79-27 (SPD) - G1-39 (+S) | Always | Below 1 Ω |
| G79-27 (SPD) or G1-39 (+S) - Body ground | Always | 10 kΩ or higher |
OK
NG
Reconnect the G79 certification ECU (smart key ECU assembly) connector.
Reconnect the G1 combination meter assembly connector.
Connect an oscilloscope to terminal G79-27 (SPD) and G77-11 (E).
Turn the power switch on (IG).
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Tester Connection | G79-27 (SPD) - G77-11 (E) |
| Tool setting | 5 V/DIV., 100 ms./DIV. |
| Vehicle condition | Power switch on (READY), vehicle being driven at approx. 5 km/h (3 mph) |
The waveform is similar to that shown in the illustration.
The wavelength becomes shorter as the vehicle speed increases.
| *a | Component with harness connected
Certification ECU (Smart Key ECU Assembly) |
OK
NG
Disconnect the 3B junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G1-39 (+S) - 3B-15 | Always | Below 1 Ω |
| G1-39 (+S) or 3B-15 - Body ground | Always | 10 kΩ or higher |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G79-27 (SPD) - 3A-37 | Always | Below 1 Ω |
| G79-27 (SPD) or 3A-37 - Body ground | Always | 10 kΩ or higher |
OK
NG