Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278082 ENGINE IMMOBILISER SYSTEM U

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  TERMINALS OF ECU  


CHECK POWER SWITCH


U159186E02
3.448,0.333 3.729,0.5 0.281,0.167 10 false G48

a.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G48-6 (AGND) - Body ground - B - Body ground Transponder key amplifier ground Always Below 1 Ω -
G48-7 (TXCT) - G48-6 (AGND) Input BR - B*1
BE - B*2
Immobiliser communication input Power switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -
G48-8 (CODE) - G48-6 (AGND) Output SB - B Immobiliser communication output Power switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -
G48-10 (VC5) - G48-6 (AGND) Input W - B Transponder key amplifier power supply Power switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -


b.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G48-7 (TXCT) - G48-6 (AGND) Input BR - B*1
BE - B*2
Signal input from certification ECU (smart key ECU assembly)
(Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into power switch, and then transmitted by transponder key amplifier antenna as radio waves)
Power switch off, key not in cabin, within 30 seconds after power switch pressed Pulse generation
(See waveform 1)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response

HINT:

If immobiliser key code certification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above



G48-8 (CODE) - G48-6 (AGND) Output SB - B Signal output to certification ECU (smart key ECU assembly)
(Radio waves from transponder key amplifier built into power switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
Power switch off, power switch pressed with key held near power switch*3 Pulse generation
(See waveform 2)
G48-10 (VC5) - G48-6 (AGND) Input W - B Transponder key amplifier power supply
(Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into power switch activated)
Power switch off, key not in cabin, within 30 seconds after power switch pressed Pulse generation
(See waveform 3)

If the result is not as specified, the power switch may have a malfunction.

*1: for LHD

*2: for RHD


HINT:

*3: Remove the key battery before performing this inspection.



c.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B051052E43
2.813,0.781 3.167,0.969 0.354,0.188 10 false GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection G48-7 (TXCT) - G48-6 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Power switch off, key not in cabin, within 30 seconds after power switch pressed


ii.
B251418E14
2.779,0.961 3.214,1.128 0.435,0.166 10 GND 2.784,1.454 2.965,1.62 0.18,0.166 10 *a 1.847,0.799 2.633,1.538 2.633,1.538 2.75,1.538 false

Waveform 2 (Reference)

Text in Illustration
*a Key held against power switch

Measurement Condition
Item Content
Tester Connection G48-8 (CODE) - G48-6 (AGND)
Tool Setting 1 V/DIV., 200 ms./DIV.
Condition Power switch off, power switch pressed with key held near power switch*

HINT:

*: Remove the key battery before performing this inspection.



iii.
B216007E01
2.887,0.987 3.231,1.157 0.343,0.170 10 GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection G48-10 (VC5) - G48-6 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Power switch off, key not in cabin, within 30 seconds after power switch pressed




CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


U183409E02
2.229,0.24 2.51,0.396 0.281,0.156 10 false G53 3.615,0.25 3.896,0.406 0.281,0.156 10 false G54 4.896,0.24 5.177,0.396 0.281,0.156 10 false G55

a.

Disconnect the G55 and G54 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G54-5 (+B) - G55-1 (E) Input BE - W-B +B power supply Always 11 to 14 V -
G54-4 (CUTB) - G55-1 (E) Input L - W-B Dark current cut pin Always 11 to 14 V -
G55-1 (E) - Body ground - W-B - Body ground Ground Always Below 1 Ω -


c.

Reconnect the G55 and G54 certification ECU (smart key ECU assembly) connector.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G54-16 (IG) - G55-1 (E) Input V - W-B Ignition power supply Power switch off → on (IG) Below 1 V → 11 to 14 V Ignition Switch
G55-8 (IND) - G55-1 (E) Output LG - W-B Security indicator output Power switch off → on (IG) Pulse generation
→ Below 2 V
-
G54-3 (TXCT) - G55-6 (AGND) Output BR - B*1
BE - B*2
Signal output to transponder key amplifier Power switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


G54-13 (CODE) - G55-6 (AGND) Input SB - B Signal input from transponder key amplifier Power switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
G54-9 (VC5) - G55-6 (AGND) Output W - B Transponder key amplifier power supply Power switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
G55-6 (AGND) - Body ground - B - Body ground Transponder key amplifier ground Always Below 1 Ω


e.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G54-3 (TXCT) - G55-6 (AGND) Output BR - B*1
BE - B*2
Signal output to transponder key amplifier
(Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into power switch, and then transmitted by transponder key amplifier antenna as radio waves)
Power switch off, key not in cabin, within 30 seconds after power switch pressed Pulse generation
(See waveform 1)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


G54-13 (CODE) - G55-6 (AGND) Input SB - B Signal input from transponder key amplifier
(Radio waves from transponder key amplifier built into power switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
Power switch off, power switch pressed with key held near power switch*3 Pulse generation
(See waveform 2)
G54-9 (VC5) - G55-6 (AGND) Output W - B Transponder key amplifier power supply
(Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into power switch activated)
Power switch off, key not in cabin, within 30 seconds after power switch pressed Pulse generation
(See waveform 3)

If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.

*1: for LHD

*2: for RHD


HINT:

*3: Remove the key battery before performing this inspection.



f.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B051052E43
2.813,0.781 3.167,0.969 0.354,0.188 10 false GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection G54-3 (TXCT) - G55-6 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Power switch off, key not in cabin, within 30 seconds after power switch pressed


ii.
B251418E14
2.779,0.961 3.214,1.128 0.435,0.166 10 GND 2.784,1.454 2.965,1.62 0.18,0.166 10 *a 1.847,0.799 2.633,1.538 2.633,1.538 2.75,1.538 false

Waveform 2 (Reference)

Text in Illustration
*a Key held against power switch

Measurement Condition
Item Content
Tester Connection G54-13 (CODE) - G55-6 (AGND)
Tool Setting 1 V/DIV., 200 ms./DIV.
Condition Power switch off, power switch pressed with key held near power switch*

HINT:

*: Remove the key battery before performing this inspection.



iii.
B216007E01
2.887,0.987 3.231,1.157 0.343,0.170 10 GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection G54-9 (VC5) - G55-6 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Power switch off, key not in cabin, within 30 seconds after power switch pressed




CHECK ID CODE BOX (IMMOBILISER CODE ECU)


U159209E02
3.448,0.25 4.021,0.51 0.573,0.26 10 false G49

a.

Disconnect the G49 ID code box (immobiliser code ECU) connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G49-1 (+B) - G49-5 (GND) Input BE - W-B +B power supply Power switch off 11 to 14 V B2789
G49-5 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω B2789

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the G49 ID code box (immobiliser code ECU) connector.


d.

Measure the voltage and check the pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G49-3 (EFII) - G49-5 (GND) Input BE - W-B EFI communication input
(Signal input from power management control ECU to ID code box (immobiliser code ECU))
Power switch off 11 to 14 V
·

B2799

·

B279A

·

Engine Start Request

·

EFI Code Receive


G49-3 (EFII) - G49-5 (GND) Input BE - W-B EFI communication input
(Signal input from power management control ECU to ID code box (immobiliser code ECU))
Within 3 seconds of engine start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected Pulse generation
(See waveform 1)
G49-4 (EFIO) - G49-5 (GND) Output LG - W-B EFI communication output
(Signal output from ID code box (immobiliser code ECU) to power management control ECU)
Power switch off Below 1 V
G49-4 (EFIO) - G49-5 (GND) Output LG - W-B EFI communication output
(Signal output from ID code box (immobiliser code ECU) to power management control ECU)
Within 3 seconds of engine start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected Pulse generation
(See waveform 2)

If the result is not as specified, the ID code box (immobiliser code ECU) may have a malfunction.



e.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B443942E01
0.698,1.26 1.156,1.458 0.458,0.198 10 false GND 2.719,1.354 3.177,1.552 0.458,0.198 10 false *a 2.906,1.354 3.365,1.552 0.458,0.198 10 false *b

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Measurement Condition
Item Content
Tester Connection G49-3 (EFII) - G49-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected


ii.

Waveform 2 (Reference)

B443943E01
0.729,1.25 1.188,1.448 0.458,0.198 10 false GND 3.115,1.354 3.573,1.552 0.458,0.198 10 false *a 3.313,1.354 3.771,1.552 0.458,0.198 10 false *b

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Measurement Condition
Item Content
Tester Connection G49-4 (EFIO) - G49-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected




CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)


U159150E02
3.552,0.281 4.063,0.615 0.51,0.333 10 false G50

a.

Measure the voltage, resistance and check the pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G50-1 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G50-3 (IGE) - G50-1 (GND) Input L - W-B Steering lock motor operation permission signal (motor operation permission signal supplied by power management control ECU) Steering lock motor operates when both conditions met, and then door opened:
·

Shift lever in P

·

Key carried, power switch turned on (IG), steering unlocked, and then power switch turned off


Pulse generation
(See waveform 1)
·

Power Supply Short

·

Unlock Request Receive

·

Lock Request Receive


G50-4 (SLP1) - G50-1 (GND) Output P - W-B Steering lock bar position signal (signal output from steering unlock sensor) Steering locked → unlocked*1 11 to 14 V → Below 1.2 V
·

Push Start Error

·

Sensor Value


G50-6 (IG2) - G50-1 (GND) Input SB - W-B IG signal (IG2 power supply input for steering lock motor) Power switch off → on (IG) Below 1 V → 11 to 14 V
·

B2788

·

Ignition Switch


G50-7 (B) - Body ground Input GR - Body ground Constant power supply Always 11 to 14 V B2788

If the result is not as specified, the steering lock ECU (steering lock actuator assembly) may have a malfunction.

HINT:

*1: The steering locks when any door is opened with the shift lever in P and the power switch off. The steering unlocks when the power switch is turned on (ACC).



b.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
U113990E03
1.708,1.708 1.792,1.99 1.792,1.99 1.844,1.99 false 1.531,0.438 2.646,0.198 2.646,0.198 2.719,0.198 false 2.646,0.208 2.448,0.458 false 2.906,1.583 3.25,1.865 0.344,0.281 10 false GND 1.917,1.917 2.406,2.063 0.49,0.146 10 false *b 2.76,0.104 3.125,0.333 0.365,0.229 10 false *a

Waveform 1 (Reference)

Text in Illustration
*a Steering lock motor not operating
*b Steering lock motor operating

Measurement Condition
Item Content
Tester Connection G50-3 (IGE) - G50-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Steering lock motor operates when both conditions met, and then door opened:
·

Shift lever in P

·

Key carried, power switch turned on (IG), steering unlocked, and then power switch turned off






CHECK POWER MANAGEMENT CONTROL ECU


U159160E02
1.469,0.198 1.76,0.365 0.292,0.167 10 false A38 2.781,0.219 3.073,0.385 0.292,0.167 10 false A39 4.25,0.229 4.531,0.396 0.281,0.167 10 false G57 5.5,0.24 5.781,0.406 0.281,0.167 10 false G58

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
A38-2 (+B2) - G57-6 (E1) Input L - BR IG power supply Power switch on (IG) 11 to 14 V -
A39-5 (+B1) - G57-6 (E1) Input L - BR IG power supply Power switch on (IG) 11 to 14 V -
A39-6 (MREL) - G57-6 (E1) Input BE - BR IG power supply Power switch on (IG) 11 to 14 V -
G57-1 (AM22) - G57-6 (E1) Input B - BR +B power supply Always 11 to 14 V -
G57-5 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G57-6 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
G58-5 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G58-7 (AM21) - G57-6 (E1) Input B - BR +B power supply Always 11 to 14 V -
G58-20 (IMO) - G57-6 (E1) Input BE - BR ID code box (immobiliser code ECU) communication input Power switch off 11 to 14 V -
G58-20 (IMO) - G57-6 (E1) Input BE - BR ID code box (immobiliser code ECU) communication input Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected Pulse generation
(See waveform 1)
-
G58-21 (IMI) - G57-6 (E1) Output LG - BR ID code box (immobiliser code ECU) communication output Power switch off Below 1 V -
G58-21 (IMI) - G57-6 (E1) Output LG - BR ID code box (immobiliser code ECU) communication output Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected Pulse generation
(See waveform 2)
-

a.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B443942E01
0.698,1.26 1.156,1.458 0.458,0.198 10 false GND 2.719,1.354 3.177,1.552 0.458,0.198 10 false *a 2.906,1.354 3.365,1.552 0.458,0.198 10 false *b

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Measurement Condition
Item Content
Tester Connection G58-20 (IMO) - G57-6 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected


ii.

Waveform 2 (Reference)

B443943E01
0.729,1.25 1.188,1.448 0.458,0.198 10 false GND 3.115,1.354 3.573,1.552 0.458,0.198 10 false *a 3.313,1.354 3.771,1.552 0.458,0.198 10 false *b

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Measurement Condition
Item Content
Tester Connection G58-21 (IMI) - G57-6 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected