Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278082 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

When there are communication malfunctions between the power management control ECU and ID code box (immobiliser code ECU), or when the communication ID codes do not match, the power management control ECU stores this DTC.

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2799 Either condition is met (1 trip detection logic*):
·

A malfunction in the communication or communication lines between the power management control ECU and ID code box (immobiliser code ECU).

·

A matching communication code cannot be verified during communication between the power management control ECU and ID code box (immobiliser code ECU).


·

ID code box (immobiliser code ECU)

·

Power management control ECU

·

Wire harness or connector


Either condition is met:
·

10 seconds after a hybrid control system start operation (with the shift lever in P and the brake pedal depressed, the power switch is pressed while carrying the key). If there is a malfunction, the hybrid control system does not start (communication begins within 3 seconds of the hybrid control system start operation, and DTCs are stored after 6 seconds).

·

10 seconds after the power switch is turned on (IG) after reconnecting the cable to the negative (-) auxiliary battery terminal (communication begins within 3 seconds of the power switch being turned on (IG), and DTCs are stored after 6 seconds).



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started -

Related Data List and Active Test
DTC Code Data List and Active Test
B2799 -

WIRING DIAGRAM

B447971E05
1.792,1.323 2.094,1.521 0.302,0.198 10 false 20 1.5,0.958 1.771,1.208 0.271,0.25 10 false IMI 5.469,0.948 5.833,1.177 0.365,0.229 10 false EFIO 5.469,1.427 5.833,1.656 0.365,0.229 10 false EFII 1.781,0.865 2.177,1.052 0.396,0.188 10 false 21 5.281,0.865 5.458,1.083 0.177,0.219 10 false 4 5.292,1.344 5.469,1.563 0.177,0.219 10 false 3 1.438,1.438 1.781,1.698 0.344,0.26 10 false IMO 0.667,1.979 1.01,2.24 0.344,0.26 10 false G58 5.146,1.969 5.49,2.229 0.344,0.26 10 false G49 0.677,2.146 1.938,2.635 1.26,0.49 10 false Power Management Control ECU 5.156,2.135 6.625,2.635 1.469,0.5 10 false ID Code Box (Immobiliser Code ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ID code box (immobiliser code ECU) or power management control ECU, refer to Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:

When DTC B2799 and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Start the hybrid control system.


b.

Wait 10 seconds or more.


c.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2799 is not output.


Result
Result Proceed to
OK A
NG (DTC B2799 is output) B
NG (Other DTCs are output) C



A

B

3.INSPECT POWER MANAGEMENT CONTROL ECU (TERMINAL IMO)

C

3.INSPECT POWER MANAGEMENT CONTROL ECU (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

U183450E02
5.906,1.552 6.188,2.323 false 0.302,0.156 0.469,0.354 0.167,0.198 10 false *a 1.229,4.104 1.396,4.302 0.167,0.198 10 false *b 0.427,3.99 0.781,4.146 0.354,0.156 10 false GND 5.521,0.552 5.802,0.719 0.281,0.167 10 false G58 6.208,2.333 6.5,2.49 0.292,0.156 10 false IMO

Text in Illustration
*a Component with harness connected
(Power Management Control ECU)
*b Waveform

Measurement Condition
Item Content
Tester Connection G58-20 (IMO) - Body ground
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after hybrid control system starts, or within 3 seconds after power switch first turned to on (IG) after auxiliary battery disconnected and reconnected

OK:

Waveform is output normally (refer to illustration).


Result
Result Proceed to
Normal waveform A
Terminal IMO stuck low (2.4 V or less) B
Terminal IMO stuck high (12 V) or Abnormal waveform C



A

4.INSPECT POWER MANAGEMENT CONTROL ECU (TERMINAL IMI)

B

7.INSPECT POWER MANAGEMENT CONTROL ECU (IMO TERMINAL VOLTAGE)

C

12.REPLACE POWER MANAGEMENT CONTROL ECU
4.INSPECT POWER MANAGEMENT CONTROL ECU (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

U183452E02
5.813,1.542 6.083,2.281 false 0.229,0.198 0.458,0.375 0.229,0.177 10 false *a 2.219,4.208 2.448,4.385 0.229,0.177 10 false *b 0.563,4.115 0.896,4.26 0.333,0.146 10 false GND 5.521,0.615 5.802,0.771 0.281,0.156 10 false G58 6.042,2.292 6.271,2.458 0.229,0.167 10 false IMI

Text in Illustration
*a Component with harness connected
(Power Management Control ECU)
*b Waveform

Measurement Condition
Item Content
Tester Connection G58-21 (IMI) - Body ground
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after hybrid control system starts, or within 3 seconds after power switch first turned to on (IG) after auxiliary battery disconnected and reconnected

OK:

Waveform is output normally (refer to illustration).


Result
Result Proceed to
Normal waveform A
Not output waveform or abnormal waveform B



A

5.REGISTER ECU COMMUNICATION ID

B

9.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
5.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.




NEXT

6.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
6.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Check that the hybrid control system starts with an already registered vehicle key.

OK:

Hybrid control system starts normally.




OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

12.REPLACE POWER MANAGEMENT CONTROL ECU
7.INSPECT POWER MANAGEMENT CONTROL ECU (IMO TERMINAL VOLTAGE)
a.
U183454E02
2.76,2.458 2.99,2.948 false 0.146,0.094 0.302,0.25 0.156,0.156 10 false *a 2.917,2.958 3.229,3.115 0.313,0.156 10 false IMO 2.51,1.625 2.792,1.781 0.281,0.156 10 false G58

Disconnect the G58 power management control ECU connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Result
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) B

Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)



A

8.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ID CODE BOX AND BODY GROUND)

B

12.REPLACE POWER MANAGEMENT CONTROL ECU
8.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ID CODE BOX AND BODY GROUND)
a.

Disconnect the G49 ID code box (immobiliser code ECU) connector.


b.

Disconnect the G58 power management control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G49-3 (EFII) - G58-20 (IMO) Always Below 1 Ω
G58-20 (IMO) - Body ground Always 10 kΩ or higher
G49-4 (EFIO) - G58-21 (IMI) Always Below 1 Ω
G58-21 (IMI) - Body ground Always 10 kΩ or higher




OK

9.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU).

HINT:

Refer to Service Bulletin.




NEXT

10.REGISTER ECU COMMUNICATION ID
10.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.




NEXT

11.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
11.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Check that the hybrid control system starts with an already registered vehicle key.

OK:

Hybrid control system starts normally.




OK

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

NG

12.REPLACE POWER MANAGEMENT CONTROL ECU
a.

Temporarily replace the power management control ECU with a new one (See page Power Source / Network>POWER DISTRIBUTION>POWER MANAGEMENT CONTROL ECU>REMOVAL).



NEXT

13.REGISTER ECU COMMUNICATION ID
13.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.




NEXT

14.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
14.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Check that the hybrid control system starts with an already registered vehicle key.

OK:

Hybrid control system starts normally.




OK

END (POWER MANAGEMENT CONTROL ECU WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)