Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › from 2014.12
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278082 ENGINE IMMOBILISER SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  Security Indicator Light Does not Blink  


DESCRIPTION

The certification ECU (smart key ECU assembly) blinks the security indicator light when the immobiliser is set (power switch off, or driver door is opened and closed with power switch on (IG)).

WIRING DIAGRAM

B432105E05
0.917,1.979 2.104,2.521 1.188,0.542 10 false Combination Meter Assembly 5.146,1.938 6.667,2.542 1.521,0.604 10 false Certification ECU (Smart Key ECU Assembly) 0.917,1.823 1.531,2.021 0.615,0.198 10 false G1 1.802,0.906 2.417,1.104 0.615,0.198 10 false 13 1.521,1 2.135,1.198 0.615,0.198 10 false LP 5.469,1.01 6.083,1.208 0.615,0.198 10 false IND 5.208,0.906 5.823,1.104 0.615,0.198 10 false 18 5.146,1.781 5.76,1.979 0.615,0.198 10 false G79

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

When an engine immobiliser system DTC is output, first perform troubleshooting for the DTC.



PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR LIGHT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Entry&Start / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Entry&Start
Tester Display Test Part Control Range Diagnostic Note
Immobiliser Indicator Security indicator light OFF/ON -

OK:

The security indicator light operates normally.




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the G1 combination meter assembly connector.


b.

Disconnect the G79 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G79-18 (IND)- G1-13 (LP) Always Below 1 Ω
G79-18 (IND) - Body ground Always 10 kΩ or higher




OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the G79 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and check the pulse according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G1-13 (LP) - Body ground Power switch off → power switch on (IG) Pulse generation → Below 2 V




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)