CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *A | Main body ECU (multiplex network body ECU) with 1 connector | *B | for LHD |
| *C | for RHD | - | - |
| *1 | Main body ECU (multiplex network body ECU) | - | - |
| *A | Main body ECU (multiplex network body ECU) with 2 connectors | - | - |
| *1 | Main body ECU (multiplex network body ECU) | - | - |
Disconnect the 3B, 3C,3E*3 and 3F*4 instrument panel junction block assembly connectors.
Measure the voltage according to the value(s) in the table below.
| Terminal No. | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 3E-1 - Body ground*3 | B - Body ground | Auxiliary battery power supply | Power switch off | 11 to 14 V |
| 3F-1 - Body ground*4 | B - Body ground | Auxiliary battery power supply | Power switch off | 11 to 14 V |
| 3C-21 - Body ground | L - Body ground | Auxiliary battery power supply | Power switch off | 11 to 14 V |
If the result is not as specified, there may be a malfunction in the wire harness.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 3B-8 - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the 3B, 3C and 3E instrument panel junction block assembly connectors.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 3B-37 - Body ground | L - Body ground | ACC power supply | Power switch on (ACC) | 11 to 14 V |
| Power switch off | Below 1 V | |||
| 3A-29 - Body ground | SB - Body ground | IG power supply | Power switch on (IG) | 11 to 14 V |
| Power switch off | Below 1 V | |||
| 3A-40 - Body ground | L - Body ground | IG signal input | Power switch on (IG) | 11 to 14 V |
| Power switch off | Below 1 V | |||
| 3A-54 - Body ground | Y - Body ground | IG signal output | Power switch on (IG) | 11 to 14 V |
| Power switch off | Below 1 V | |||
| G59-15 (DOMR) - Body ground*1 | BR - Body ground | DOME CUT relay drive output | DOME CUT relay off | 11 to 14 V |
| DOME CUT relay on | Below 1 V | |||
| 3B-34 - Body ground*2 | BE - Body ground | DOME CUT relay drive output | DOME CUT relay off | 11 to 14 V |
| DOME CUT relay on | Below 1 V | |||
| 3C-4 - Body ground | G - Body ground | Interior lights power supply | DOME CUT relay off | Below 1 V |
| DOME CUT relay on | 11 to 14 V | |||
| 3A-5 - Body ground | BE - Body ground | Interior lights power supply | DOME CUT relay off | Below 1 V |
| DOME CUT relay on | 11 to 14 V | |||
| 3B-6 - Body ground | B - Body ground | Interior lights drive output | Power switch off, interior lights off (when operated by illuminated entry system) | 11 to 14 V |
| Power switch off, interior lights on (when operated by illuminated entry system) | Below 1 V | |||
| 3D-6 - Body ground | L - Body ground | Luggage compartment room light power supply | DOME CUT relay off | Below 1 V |
| DOME CUT relay on | 11 to 14 V | |||
| 3D-35 - Body ground | B - Body ground | Back door courtesy light switch input | Back door open | Below 1 V |
| Back door closed | 11 to 14 V | |||
| 3D-36 - Body ground | R - Body ground | Front door courtesy light switch LH input | Front door LH open | Below 1 V |
| Front door LH closed | Pulse generation | |||
| G59-19 (FRCY) - Body ground | R - Body ground | Front door courtesy light switch RH input | Front door RH open | Below 1 V |
| Front door RH closed | Pulse generation | |||
| G59-24 (LCTY) - Body ground | L - Body ground | Rear door courtesy light switch LH input | Rear door LH open | Below 1 V |
| Rear door LH closed | Pulse generation | |||
| G59-6 (RCTY) - Body ground | G - Body ground | Rear door courtesy light switch RH input | Rear door RH open | Below 1 V |
| Rear door RH closed | Pulse generation | |||
| G59-7 (LSFL) - Body ground | L - Body ground | Front door unlock detection switch LH input | Front door LH locked | Pulse generation |
| Front door LH unlocked | Below 1 V | |||
| G59-18 (LSFR) - Body ground | L - Body ground | Front door unlock detection switch RH input | Front door RH locked | Pulse generation |
| Front door RH unlocked | Below 1 V | |||
| 3D-24 - Body ground | Y - Body ground | Rear door unlock detection switch LH input | Rear door LH and rear door RH locked | Pulse generation |
| Rear door LH or rear door RH unlocked | Below 1 V | |||
| 3D-25 - Body ground | V - Body ground | Rear door unlock detection switch RH input | Rear door LH and rear door RH locked | Pulse generation |
| Rear door LH or rear door RH unlocked | Below 1 V |
*1: LED Headlight Type
*2: Halogen Headlight
*3: for LHD
*4: for RHD
If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G79-16 (SWIL) - G79-24 (AGND) | R - B | Power switch illumination drive output | Power switch illumination on | 11 to 14 V |
| Power switch illumination off | Below 1 V |
If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.