Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057036 LIGHTING (INT) _0278087 LIGHTING SYSTEM U

LIGHTING (INT)  LIGHTING SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ACC SW Power switch on (ACC) signal/ON or OFF ON: Power switch on (ACC)
OFF: Power switch off
-
IG SW Power switch on (IG) signal/ON or OFF ON: Power switch on (IG)
OFF: Power switch off
-
RR Door Courtesy Rear door courtesy light switch RH signal/OPEN or CLOSE OPEN: Rear door RH open
CLOSE: Rear door RH closed
-
RL Door Courtesy Rear door courtesy light switch LH signal/OPEN or CLOSE OPEN: Rear door LH open
CLOSE: Rear door LH closed
-
Back Door Courtesy SW Back door courtesy switch signal/ON or OFF ON: Back door open
OFF: Back door closed
-
FR Door Lock Pos Front door RH unlock detection switch signal/LOCK or UNLOCK LOCK: Front door RH locked
UNLOCK: Front door RH unlocked
-
FR Door Courtesy Front door courtesy light switch RH signal/OPEN or CLOSE OPEN: Front door RH open
CLOSE: Front door RH closed
-
FL Door Lock Pos Front door LH unlock detection switch signal/LOCK or UNLOCK LOCK: Front door LH locked
UNLOCK: Front door LH unlocked
-
FL Door Courtesy Front door courtesy light switch LH signal/OPEN or CLOSE OPEN: Front door LH open
CLOSE: Front door LH closed
-
RR-Door Lock Pos SW Rear door RH unlock detection switch signal/ON or OFF ON: Rear door LH locked and rear door RH unlocked
ON: Rear door LH unlocked and rear door RH locked
ON: Rear door LH and rear door RH unlocked
OFF: Rear door LH and rear door RH locked
-
RL-Door Lock Pos SW Rear door LH unlock detection switch/ON or OFF ON: Rear door LH locked and rear door RH unlocked
ON: Rear door LH unlocked and rear door RH locked
ON: Rear door LH and rear door RH unlocked
OFF: Rear door LH and rear door RH locked
-
I/L ON W/Door Key Unlock Function that lights up the interior lights when the doors are unlocked/OFF or ON OFF: Function disabled
ON: Function enabled
Customized value is displayed
Lighting Time Lighting time of the delay control function (illuminated entry system)/15s, 7.5s or 30s 15s: 15 seconds
7.5s: 7.5 seconds
30s: 30 seconds
Customized value is displayed
Room Light when Aprchd Function that lights up the interior lights when a key enters any actuation area/OFF or ON OFF: Function disabled
ON: Function enabled
Customized value is displayed
I/L when ACC OFF Function that lights up the interior lights when the power switch is turned from on (ACC or IG) to off/OFF or ON OFF: Function disabled
ON: Function enabled
Customized value is displayed



ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / (desired system) / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Illuminated Entry System Personal light and power switch illumination ON/OFF Interior light door switch DOOR
Relay for Interior Light Auto Cut Function DOME CUT Relay ON/OFF -

Entry&Start
Tester Display Test Part Control Range Diagnostic Note
Power/Engine SW Light Power switch light OFF/ON When performing this Active Test, make sure the following condition is met:
The power switch illumination is off (15 seconds or more have elapsed since it turned from on to off) and the power switch is on (ACC) or on (IG), or the hybrid control system is running.