Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2015.11–2017.06
RM2170E _58 Vehicle Interior _057037 METER / GAUGE / DISPLAY _0278095 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Malfunction in Water Temperature Warning Light  


DESCRIPTION

In this circuit, the combination meter assembly receives engine coolant temperature signals from the ECM using the CAN communication system. The combination meter assembly displays an engine coolant temperature warnings based on the data received from the ECM.

WIRING DIAGRAM

E337681E10
0.615,3.094 1.156,3.354 0.542,0.26 10 false ECM 2.948,3.177 4.802,3.604 1.854,0.427 10 false : CAN Communication Line 5.219,3.104 7.073,3.615 1.854,0.51 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

HINT:
·

If there is an open or short in the engine coolant temperature sensor circuit, the ECM stores the DTCs. Troubleshoot the SFI system (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DIAGNOSTIC TROUBLE CODE CHART).

·

If the exhaust heat recirculation system has a malfunction, the water temperature warning is displayed to inform the driver of the malfunction.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result:
Result Proceed to
CAN communication DTCs are not output. A
CAN communication DTCs are output. B




A

2.CHECK FOR DTC

B

2.CHECK FOR DTC
a.

Check for DTCs (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs are not output. A
SFI system DTCs are output. B




A

3.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMPERATURE, COOLANT TEMP)

B

3.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMPERATURE, COOLANT TEMP)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus:

i.

for Combination Meter: Body / Combination Meter / Data List.


ii.

for Engine: Powertrain / Engine and ECT / Data List.



e.

Check the values by referring to the table below.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Coolant Temperature Engine coolant temperature / 0 to 127.5°C (0 to 261.5°F) After warming up: 75 to 100°C (167 to 212°F) -

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Stored as Freeze Frame Data
Coolant Temp Engine coolant temperature/
Min.: -40°C (-40°F), Max.: 140°C (284°F)
75 to 100°C (167 to 212°F): After warming up
·

Stored as Freeze Frame Data

·

This is the engine coolant temperature.


HINT:
·

After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).

·

After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.

·

If the value is -40°C (-40°F) or higher than 135°C (275°F), the sensor circuit may be open or shorted.

·

Check if the engine overheats when the value indicates higher than 140°C (284°F).




NOTICE:

Enter inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


Result:
Result Proceed to
The data list values of the ECUs do not match. A
The data list values of the ECUs match. B


HINT:

When the Data List values of the ECUs do not match, a signal output error of the ECM is suspected.




A

4.REPLACE COMBINATION METER ASSEMBLY

B

4.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new or a known good one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).

OK:

The operation of the water temperature warning light returns to normal.




OK

END

NG