Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2014.12–2015.11
RM2170E _58 Vehicle Interior _057037 METER / GAUGE / DISPLAY _0278095 METER / GAUGE SYSTEM G

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 83100 1.INSPECT COMBINATION METER ASSEMBLY

a.

Check speedometer operation.

NOTICE:
·

The combination meter assembly receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.

·

The Data List values of the skid control ECU are used for this inspection. Therefore, make sure to perform the inspection after confirming that no DTCs are output from the brake control system.

·

If the tire size or tire inflation pressure is not within the specified range, or the tires are excessively worn, the speedometer indication error will increase. Therefore, make sure to perform the inspection after checking that the tire size, tire inflation pressure and tire wear are in the specified range.



i.

Before starting the following inspection, check if brake control system DTCs are output.


ii.

Check the values by referring to the table below.

ABS/VSC/TRC:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations


Reference: (km/h) except Australia
Intelligent tester indication (km/h) Acceptable Range (km/h)
20 21.0 to 25.0
40 42.0 to 46.0
60 63.0 to 67.0
80 84.0 to 88.0
100 104.0 to 109.0
120 125.0 to 130.0
140 146.0 to 151.0
160 167.0 to 173.0
180 187.0 to 194.0
200 208.0 to 215.0
220 229.0 to 236.0
240 249.0 to 257.0
260 270.0 to 278.0

Reference: (km/h) for Australia
Intelligent tester indication (km/h) Acceptable Range (km/h)
Data in ( ) is for reference
20 20.3 to 24.3
40 40.5 to 45.0
60 60.8 to 65.3
80 81.1 to 86.1
100 101.3 to 105.3
120 121.6 to 126.6
140 141.9 to 146.9
160 162.1 to 167.1
180 182.4 to 187.4
200 (202.7 to 207.7)

Reference: (mph)
Intelligent tester indication (mph) Acceptable Range (mph)
Data in ( ) is for reference
20 21.0 to 23.0
40 42.0 to 44.0
60 63.0 to 66.0
80 83.0 to 87.0
100 104.0 to 108.0
120 125.0 to 129.0
140 146.0 to 150.0
160 166.0 to 171.0
180 187.0 to 192.0
200 (208.0 to 213.0)



b.

CHECK LED ILLUMINATION (BULB CHECK)

i.

Check the illumination function of the warning or indicator lights listed below when turning the power switch on (IG).

OK:
Warning or Indicator Light Specified Condition
Master warning light Warning light comes on for about 3 seconds after turning the power switch to on (IG).
SRS warning light Warning light comes on for about 6 seconds after turning the power switch to on (IG).
Charge warning light Warning light comes on when turning the power switch to on (IG).
EPS warning light
MIL (Check engine warning light)
Brake warning light / red (malfunction)
·

Warning or indicator light comes on for about 3 seconds after turning the power switch to on (IG).

·

Warning or indicator light comes on for about 3 seconds when turning the power switch from off to on (READY).


Slip indicator light
ABS warning light
Brake warning light / yellow (minor malfunction)
VSC OFF indicator light