83100
1.INSPECT COMBINATION METER ASSEMBLY
Check speedometer operation.
The combination meter assembly receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.
The Data List values of the skid control ECU are used for this inspection. Therefore, make sure to perform the inspection after confirming that no DTCs are output from the brake control system.
If the tire size or tire inflation pressure is not within the specified range, or the tires are excessively worn, the speedometer indication error will increase. Therefore, make sure to perform the inspection after checking that the tire size, tire inflation pressure and tire wear are in the specified range.
Before starting the following inspection, check if brake control system DTCs are output.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Vehicle Speed | Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Intelligent tester indication (km/h) | Acceptable Range (km/h) |
|---|---|
| 20 | 21.0 to 25.0 |
| 40 | 42.0 to 46.0 |
| 60 | 63.0 to 67.0 |
| 80 | 84.0 to 88.0 |
| 100 | 104.0 to 109.0 |
| 120 | 125.0 to 130.0 |
| 140 | 146.0 to 151.0 |
| 160 | 167.0 to 173.0 |
| 180 | 187.0 to 194.0 |
| 200 | 208.0 to 215.0 |
| 220 | 229.0 to 236.0 |
| 240 | 249.0 to 257.0 |
| 260 | 270.0 to 278.0 |
| Intelligent tester indication (km/h) | Acceptable Range (km/h)
Data in ( ) is for reference |
|---|---|
| 20 | 20.3 to 24.3 |
| 40 | 40.5 to 45.0 |
| 60 | 60.8 to 65.3 |
| 80 | 81.1 to 86.1 |
| 100 | 101.3 to 105.3 |
| 120 | 121.6 to 126.6 |
| 140 | 141.9 to 146.9 |
| 160 | 162.1 to 167.1 |
| 180 | 182.4 to 187.4 |
| 200 | (202.7 to 207.7) |
| Intelligent tester indication (mph) | Acceptable Range (mph)
Data in ( ) is for reference |
|---|---|
| 20 | 21.0 to 23.0 |
| 40 | 42.0 to 44.0 |
| 60 | 63.0 to 66.0 |
| 80 | 83.0 to 87.0 |
| 100 | 104.0 to 108.0 |
| 120 | 125.0 to 129.0 |
| 140 | 146.0 to 150.0 |
| 160 | 166.0 to 171.0 |
| 180 | 187.0 to 192.0 |
| 200 | (208.0 to 213.0) |
CHECK LED ILLUMINATION (BULB CHECK)
Check the illumination function of the warning or indicator lights listed below when turning the power switch on (IG).
| Warning or Indicator Light | Specified Condition |
|---|---|
| Master warning light | Warning or indicator light comes on for about 3 seconds after turning the power switch to on (IG). |
| Vehicle proximity notification off indicator light*1 | |
| Tire pressure warning light*2 | |
| SRS warning light | Warning light comes on for about 6 seconds after turning the power switch to on (IG). |
| Charge warning light | Warning light comes on when turning the power switch to on (IG). |
| EPS warning light | |
| MIL (Check engine warning light) | |
| Brake warning light / red (malfunction) | ·
Warning or indicator light comes on for about 3 seconds after turning the power switch to on (IG). ·
Warning or indicator light comes on for about 3 seconds when turning the power switch from off to on (READY). |
| Slip indicator light | |
| ABS warning light | |
| Brake warning light / yellow (minor malfunction) | |
| VSC OFF indicator light |
*1: w/ Vehicle Proximity Notification System
*2: w/ Tire Pressure Warning System