Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278099 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

DTCs are displayed by blinking of the SRS warning light.

HINT:
·

When multiple warning lights in the combination meter blink continuously, a ground short in the wiring or an ECU connected to terminal TC of the DLC3 is suspected.

·

A DTC output mode signal is transmitted through the CAN communication system to each ECU including the airbag sensor assembly. Thus when multiple systems do not enter DTC output mode, there may be a power management control ECU malfunction.



WIRING DIAGRAM

C241762E09
1.498,1.077 1.918,1.219 0.420,0.142 10 CA1H 1.498,1.783 1.918,1.925 0.420,0.142 10 CA1L 5.827,1.077 6.247,1.219 0.420,0.142 10 CANH 5.827,1.783 6.247,1.925 0.420,0.142 10 CANL 1.701,2.492 1.919,2.634 0.218,0.142 10 TC 0.482,3.104 2.566,3.272 2.084,0.167 10 Power Management Control ECU 2.006,1.088 2.291,1.230 0.285,0.142 10 G58 2.065,0.851 2.237,1.007 0.172,0.156 10 25 2.065,1.556 2.237,1.712 0.172,0.156 10 24 2.051,2.28 2.223,2.436 0.172,0.156 10 11 5.536,1.638 5.708,1.794 0.172,0.156 10 22 5.536,0.93 5.708,1.086 0.172,0.156 10 13 0.879,5.481 2.604,5.642 1.725,0.161 10 : CAN Communication Line 1.261,4.121 1.493,4.260 0.232,0.139 10 CG 1.678,4.121 1.910,4.260 0.232,0.139 10 TC 2.01,3.999 2.191,4.151 0.180,0.152 10 13 1.03,3.999 1.132,4.151 0.102,0.152 10 4 1.201,4.598 1.565,4.764 0.364,0.166 10 G4 1.201,4.745 1.579,4.914 0.378,0.170 10 DLC3 5.341,4.934 5.646,5.079 0.305,0.145 10 G18 5.341,5.091 6.884,5.271 1.543,0.180 10 Airbag Sensor Assembly 2.006,1.793 2.289,1.935 0.283,0.142 10 G58 2.006,2.502 2.288,2.644 0.282,0.142 10 G57

PROCEDURE

1.CHECK WIRE HARNESS (TC OF DLC3 - TC OF POWER MANAGEMENT CONTROL ECU)
a.
U183519E02
1.802,1.625 2.125,2.021 true 1.729,3.719 1.5,4.333 true 0.313,0.188 0.531,0.375 0.219,0.188 10 false *1 2.083,2.042 2.333,2.219 0.25,0.177 10 false TC 0.333,2.51 0.552,2.698 0.219,0.188 10 false *a 1.396,4.354 1.688,4.521 0.292,0.167 10 false TC 0.302,1.281 0.573,1.438 0.271,0.156 10 false G4 0.396,3.594 0.729,3.75 0.333,0.156 10 false G57

Turn the power switch off.


b.

Disconnect the connector from the power management control ECU.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-13 (TC) - G57-11 (TC) Always Below 1 Ω


Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to Power Management Control ECU)



OK

2.CHECK WIRE HARNESS (CG OF DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE WIRE HARNESS

2.CHECK WIRE HARNESS (CG OF DLC3 - BODY GROUND)
a.
U159331E02
1.615,0.792 1.615,0.271 1.615,0.271 1.802,0.271 false 0.156,0.094 0.385,0.302 0.229,0.208 10 false *1 1.865,0.188 2.302,0.427 0.438,0.24 10 false CG 0.25,1 0.5,1.156 0.25,0.156 10 false G4

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-4 (CG) - Body ground Always Below 1 Ω


Text in Illustration
*1 DLC3



OK

3.CHECK WIRE HARNESS (TC OF DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE WIRE HARNESS

3.CHECK WIRE HARNESS (TC OF DLC3 - BODY GROUND)
a.
U159332E01
0.054,0.065 0.202,0.205 0.149,0.140 10 *1 2.03,1.775 2.257,1.912 0.227,0.137 10 TC 1.805,1.339 1.805,1.861 1.805,1.861 1.991,1.861 false 0.262,0.998 0.528,1.154 0.266,0.156 10 G4

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-13 (TC) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 DLC3



OK

NG

REPAIR OR REPLACE WIRE HARNESS OR REPLACE EACH ECU