Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2011.12–2017.06
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278099 AIRBAG SYSTEM D

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  DIAGNOSIS SYSTEM  



FUNCTION OF SRS WARNING LIGHT


a.

Primary check

i.

Turn the power switch off. Wait for at least 2 seconds, then turn the power switch on (IG). The SRS warning light comes on for approximately 6 seconds and the diagnosis of the airbag system (including the seat belt pretensioners) is performed.

HINT:

If malfunctions are detected during the primary check, the SRS warning light remains on even after the primary check period of approximately 6 seconds.




b.

Constant check

i.

After the primary check, the airbag sensor assembly constantly monitors the airbag system for malfunctions.

HINT:

If malfunctions are detected during the constant check, the airbag sensor assembly functions as follows:

·

The SRS warning light comes on.

·

The SRS warning light goes off, and then comes on. This indicates a source voltage drop. The SRS warning light goes off 10 seconds after the source voltage returns to normal.





c.

Review

i.

When the airbag system is normal:

The SRS warning light comes on only during the primary check period of approximately 6 seconds after the power switch is turned on (IG).


ii.

When the airbag system is malfunctioning:

·

The SRS warning light remains on even after the primary check period.

·

The SRS warning light goes off after the primary check, but comes on again during the constant check.

·

The SRS warning light does not come on when turning the power switch from off to on (IG).


HINT:

The airbag sensor assembly keeps the SRS warning light on if airbags have been deployed.





SRS WARNING LIGHT CHECK


a.
C093955

Turn the power switch on (IG), and check that the SRS warning light comes on for approximately 6 seconds (primary check).


b.

Check that the SRS warning light goes off approximately 6 seconds after the power switch is turned on (IG) (constant check).

HINT:

When any of the following symptoms occur, refer to Problem Symptoms Table (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PROBLEM SYMPTOMS TABLE).

·

The SRS warning light comes on occasionally after the primary check period.

·

The SRS warning light comes on, but a DTC is not output.

·

The power switch is turned from off to on (IG), but the SRS warning light does not come on.





FUNCTION OF SRS CONNECTORS


a.

The SRS connectors are located as shown in the illustration.

C249353E02
3.186,3.814 3.359,3.959 0.173,0.145 10 17 3.45,4.282 3.623,4.427 0.173,0.145 10 18 3.186,2.796 3.359,2.942 0.173,0.145 10 17 3.45,3.268 3.625,3.413 0.176,0.145 10 18 0.663,1.916 2.592,2.266 1.929,0.350 10 Combination Meter Assembly (SRS Warning Light) 0.796,3.168 2.591,3.317 1.795,0.150 10 Front Airbag Sensor LH 3.792,4.067 4.002,4.213 0.210,0.145 10 15 4.217,4.067 4.418,4.213 0.201,0.145 10 16 3.796,3.067 4.007,3.212 0.210,0.145 10 15 4.221,3.067 4.422,3.212 0.201,0.145 10 16 0.806,4.159 2.313,4.325 1.508,0.166 10 Front Airbag Sensor RH 3.862,6.093 4.035,6.239 0.173,0.145 10 9 4.249,6.093 4.423,6.239 0.173,0.145 10 10 1.658,6.839 1.831,6.985 0.173,0.145 10 7 1.908,7.292 2.081,7.438 0.173,0.145 10 8 3.186,5.832 3.359,5.977 0.173,0.145 10 11 3.45,6.294 3.623,6.440 0.173,0.145 10 12 3.45,5.293 3.623,5.438 0.173,0.145 10 14 3.186,4.828 3.359,4.973 0.173,0.145 10 13 4.045,6.839 4.218,6.985 0.173,0.145 10 5 4.322,7.292 4.498,7.438 0.176,0.145 10 6 2.567,6.957 3.945,7.303 1.379,0.346 10 Spiral Cable with Sensor Sub-assembly 0.153,4.933 3.130,5.382 2.977,0.449 10 Lower No. 1 Instrument Panel Airbag Assembly (Driver Side Knee Airbag Squib) 0.191,5.953 3.167,6.402 2.977,0.449 10 Instrument Panel Passenger Airbag Assembly (Front Passenger Side Squib) 0.162,6.957 1.570,7.307 1.407,0.350 10 Horn Button Assembly (Driver Side Squib) 6.549,1.453 6.653,1.595 0.104,0.141 10 4 6.549,1.145 6.653,1.290 0.104,0.145 10 3 5.677,1.453 5.781,1.595 0.104,0.141 10 4 5.677,1.145 5.781,1.290 0.104,0.145 10 3 5.674,1.297 5.785,1.438 0.111,0.141 10 A 4.903,0.624 6.639,0.769 1.736,0.146 10 Airbag Sensor Assembly 4.734,1.453 4.838,1.595 0.104,0.141 10 2 4.734,1.145 4.838,1.290 0.104,0.145 10 1

C247190E07
4.823,0.604 6.635,0.75 1.813,0.146 10 false Airbag Sensor Assembly 6.521,1.417 6.625,1.563 0.104,0.146 10 false 4 6.521,1.104 6.625,1.25 0.104,0.146 10 false 3 4.646,1.417 4.75,1.563 0.104,0.146 10 false 2 4.646,1.104 4.75,1.25 0.104,0.146 10 false 1 5.583,1.417 5.688,1.563 0.104,0.146 10 false 4 5.583,1.104 5.688,1.25 0.104,0.146 10 false 3 5.583,1.26 5.698,1.406 0.115,0.146 10 false A 2.802,5.552 2.979,5.698 0.177,0.146 10 false 25 3.063,6.031 3.24,6.177 0.177,0.146 10 false 26 0.354,5.698 2.552,6.073 2.198,0.375 10 false Curtain Shield Airbag Assembly LH (Curtain Shield Squib LH) 2.802,6.833 2.979,6.979 0.177,0.146 10 false 27 3.063,7.344 3.24,7.49 0.177,0.146 10 false 28 0.354,6.979 2.542,7.375 2.188,0.396 10 false Front Seat Outer Belt Assembly LH (Front Pretensioner Squib LH) 2.802,3 2.979,3.146 0.177,0.146 10 false 21 3.063,3.542 3.24,3.688 0.177,0.146 10 false 22 0.24,3.333 2.698,3.542 2.458,0.208 10 false Side No. 2 Airbag Sensor Assembly LH 2.802,4.281 2.979,4.427 0.177,0.146 10 false 23 3.063,4.771 3.24,4.917 0.177,0.146 10 false 24 0.469,4.417 2.469,4.771 2,0.354 10 false Front Seat Airbag Assembly LH (Side Squib LH) 2.802,1.708 2.979,1.854 0.177,0.146 10 false 19 3.063,2.25 3.24,2.396 0.177,0.146 10 false 20 0.417,2.063 2.51,2.333 2.094,0.271 10 false Side Airbag Sensor Assembly LH

C247163E08
0.819,0.481 2.629,0.626 1.810,0.146 10 Airbag Sensor Assembly 2.531,1.272 2.635,1.413 0.104,0.141 10 4 2.531,0.963 2.635,1.108 0.104,0.145 10 3 1.559,1.272 1.663,1.413 0.104,0.141 10 4 1.559,0.963 1.663,1.108 0.104,0.145 10 3 0.606,1.272 0.710,1.413 0.104,0.141 10 2 0.606,0.963 0.710,1.108 0.104,0.145 10 1 1.559,1.115 1.670,1.256 0.111,0.141 10 A 3.809,2.848 3.982,2.993 0.173,0.145 10 21 3.546,3.356 3.722,3.502 0.176,0.145 10 22 4.254,3.236 6.746,3.379 2.492,0.143 10 Side No. 2 Airbag Sensor Assembly RH 3.809,1.5 3.982,1.646 0.173,0.145 10 19 3.546,2.065 3.726,2.211 0.180,0.145 10 20 4.44,1.897 6.564,2.047 2.124,0.149 10 Side Airbag Sensor Assembly RH 3.809,5.517 3.982,5.662 0.173,0.145 10 25 3.546,6.003 3.719,6.148 0.173,0.145 10 26 4.39,5.629 6.613,5.936 2.223,0.307 10 Curtain Shield Airbag Assembly RH (Curtain Shield Squib RH) 3.809,6.837 3.982,6.983 0.173,0.145 10 27 3.546,7.325 3.719,7.471 0.173,0.145 10 28 4.383,6.948 6.620,7.264 2.236,0.316 10 Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH) 3.546,4.687 3.719,4.832 0.173,0.145 10 24 3.809,4.189 3.982,4.334 0.173,0.145 10 23 4.508,4.313 6.498,4.624 1.990,0.311 10 Front Seat Airbag Assembly RH (Side Squib RH)

Connector Type Application
Terminal Twin-lock Mechanism Connectors 2, 4, 6, 9, 10, 15, 16
Half Connection Prevention Mechanism Connectors 6, 10, 15
Activation Prevention Mechanism Connectors 2, 4, 5, 7, 9, 11, 13, 23, 25, 27
Connector Lock Mechanism (1) Connectors 8, 12, 14, 26, 28
Connector Position Assurance Mechanism Connectors 18, 20, 22, 24
Connector Lock Mechanism (2) Connector A
Improper Connection Prevention Lock Mechanism Connector A


b.

Terminal twin-lock mechanism

C190972E01
0.651,0.02 2.002,0.194 1.350,0.174 10 Lance (Primary Lock) 1.231,1.444 2.164,1.619 0.934,0.174 10 Primary Lock 3.944,0.024 5.618,0.199 1.674,0.174 10 Spacer (Secondary Lock) 4.892,1.43 5.946,1.605 1.054,0.174 10 Secondary Lock 2.435,0.092 2.057,0.095 false 2.821,0.622 2.435,0.092 false 5.712,0.092 5.569,0.095 false 5.821,0.608 5.712,0.092 false

i.

This mechanism is designed to increase the ability of the terminal to remain connected and prevent it from accidentally being disconnected.


ii.

The connector has a two-piece construction consisting of the housing and spacer to securely lock the terminal using both the lance (primary lock) and spacer (secondary lock).



c.

Half connection prevention mechanism

C147461E70
1.542,1.417 1.448,1.083 1.448,1.083 1.302,1.083 false 1.833,1.375 1.667,0.823 1.667,0.823 1.521,0.823 false 2.375,1.323 2.094,0.542 2.094,0.542 1.948,0.542 false 2.99,1.198 3.208,0.573 3.208,0.573 3.375,0.573 false 3.281,1.302 3.458,0.875 3.458,0.875 3.615,0.875 false 6.083,1.146 5.885,0.74 5.885,0.74 5.708,0.74 false 1.146,0.458 1.979,0.625 0.833,0.167 10 false Locking Arm 1.01,0.74 1.552,0.906 0.542,0.167 10 false Stopper 0.51,1 1.344,1.177 0.833,0.177 10 false Locking Part 3.427,0.5 3.865,0.688 0.438,0.188 10 false Slider 3.656,0.802 4.125,0.99 0.469,0.188 10 false Spring 5.198,0.646 5.781,0.833 0.583,0.188 10 false Stopper 4.646,1.948 5.979,2.135 1.333,0.188 10 false Rebounded by Slider

i.

This mechanism is designed to prevent the connector from being connected only halfway.


ii.

If the connector is not completely connected, the connector is disconnected due to the spring force so that no continuity exists.



d.

Activation prevention mechanism

C238382E13
1.594,1.073 1.208,0.927 false 5.26,1.521 5.26,2.042 true 1.844,1.667 1.844,2.083 false 1.656,1.458 1.198,1.458 true 2.646,1.646 2.969,1.646 true 2.354,1.396 3,0.979 3,0.979 2.552,1.469 true 1.771,0.375 2.542,0.542 0.771,0.167 10 false When open 0.323,0.823 1.229,1.01 0.906,0.188 10 false Male Housing 3.042,0.885 4.125,1.042 1.083,0.156 10 false Female Terminal 0.302,1.375 1.219,1.542 0.917,0.167 10 false Male Terminal 3.01,1.573 4.073,1.76 1.063,0.188 10 false Female Housing 1.26,2.104 2.427,2.271 1.167,0.167 10 false Short Spring Plate 5.448,0.375 6.365,0.542 0.917,0.167 10 false When shorted 4.375,2.063 6.167,2.385 1.792,0.323 10 false Short spring plate contacting the male terminal

i.

The activation prevention mechanism is designed to create a short circuit automatically between the positive and negative terminals of an airbag power source connector when disconnected.


ii.

The short spring plate contained in the connector creates a closed circuit on the airbag side (no potential difference can occur between both terminals), preventing accidental airbag deployment when servicing.



e.

Connector lock mechanism (1)

C147462E03
2.521,0.344 2.021,0.198 false 2.635,0.76 2.281,0.885 false 2.469,1.24 2.271,1.323 false 4.927,0.896 5.24,0.688 false 0.531,0.115 2.01,0.292 1.479,0.177 10 Lock the locking button 1.927,0.813 2.302,0.979 0.375,0.167 10 Claw 1.792,1.25 2.281,1.417 0.49,0.167 10 Groove 5.281,0.604 6.927,1.031 1.646,0.427 10 Claw on the locking button is locked in the groove

i.

This mechanism is designed to prevent the connector from accidentally being disconnected.


ii.

Locking the connector lock button engages the locking button claw to the groove on the other side connector to connect the connector securely.



f.

Connector Position Assurance (CPA) mechanism

C161464E01
1.058,0.13 2.269,0.299 1.211,0.170 10 Female Connector 1.261,0.41 2.097,0.580 0.836,0.170 10 Locking Part 1.003,2.219 2.062,2.396 1.059,0.177 10 Male Connector 2.963,0.298 4.550,0.454 1.586,0.156 10 Primary Lock Completed 5.072,0.298 6.839,0.454 1.767,0.156 10 Secondary Lock Completed 4.898,0.699 5.526,0.875 0.628,0.177 10 Retainer 0.858,0.198 1.016,0.2 false 0.837,1.105 0.858,0.198 false 1.051,0.478 1.217,0.478 false 0.933,1.2 1.051,0.478 false 0.727,2.289 0.958,2.289 false 0.511,1.797 0.727,2.289 false 5.63,0.779 5.464,0.779 false 5.66,1.096 5.63,0.779 false

i.

This mechanism is designed to detect when the connector is connected only halfway.


ii.

The CPA and female connector slide to the male connector side at the same time and the primary lock is completed when the female connector is engaged with the male connector. From this point, only the CPA slides to the male connector side and secondary lock is completed when the CPA retainer is engaged with the female connector. When the CPA and female connector ends are aligned, they are completely engaged.



g.

Connector lock mechanism (2)

C330363E01
0.854,1.927 1.021,1.927 1.021,1.927 1.198,1.469 false 2.469,3.583 2.292,3.583 2.292,3.583 1.865,3.156 false 3.719,3.146 3.906,3.146 3.906,3.146 4.167,2.813 false 4.781,3.417 5.125,3.417 5.125,3.417 5.542,3.323 false 5.573,2.646 5.688,2.646 5.688,2.646 5.813,2.781 false 4.438,1.406 4.708,1.698 4.708,1.698 4.917,1.698 false 0.417,1.844 0.875,2.042 0.458,0.198 10 false Lance 2.521,3.51 3.094,3.75 0.573,0.24 10 false Retainer 4.969,1.615 5.635,1.823 0.667,0.208 10 false Holder 6.073,2.302 6.448,2.479 0.375,0.177 10 true Claw 3.167,3.052 3.74,3.292 0.573,0.24 10 false Retainer 5.125,2.531 5.792,2.74 0.667,0.208 10 false Holder 4.208,3.313 4.781,3.552 0.573,0.24 10 false Retainer

i.

This mechanism is designed to prevent the connector from accidentally being disconnected.


ii.

Sliding the connector all the way into the holder and locking the lance completes the primary lock.


iii.

Engaging the retainer to the holder as shown in the illustration completes the secondary lock, preventing the connector from accidentally being disconnected.



h.

Improper connection prevention lock mechanism

C204952E05
5.292,0.802 5.292,0.229 5.292,0.229 5.656,0.229 false 5.292,1.167 5.292,1.875 5.292,1.875 4.594,1.875 false 4.958,2.979 4.573,2.979 false 1.104,1.49 1.104,2.406 1.104,2.406 0.948,2.406 false 1.031,1.177 1.031,0.51 1.031,0.51 1.344,0.51 false 6.01,0.719 6.01,1.031 6.01,1.031 5.521,1.031 false 3.958,0.073 4.604,0.292 0.646,0.219 10 false Top View 0.24,2.323 0.979,2.646 0.74,0.323 10 false Unlock Rib 3.917,1.771 4.646,2.313 0.729,0.542 10 false Temporary Hold Lock 4.219,2.885 4.604,3.229 0.385,0.344 10 false Lever 5.708,0.156 6.49,0.5 0.781,0.344 10 false Unlock Rib 1.385,0.438 1.594,0.698 0.208,0.26 10 false A 5.969,0.563 6.125,0.708 0.156,0.146 10 false A

i.

This mechanism is designed to prevent the connector from being connected only halfway.


ii.

When the holder is connected to the airbag sensor assembly, the unlock rib unlocks the temporary hold lock, allowing the lever to be pushed in by rotating around the axis A.


iii.

Locking the lever to the holder locks the holder securely.




ACTIVATION PREVENTION MECHANISM


a.

Function of activation prevention mechanism

i.

An activation prevention mechanism is built into the connector (on the airbag sensor assembly side) of the airbag system squib circuit to prevent accidental airbag activation.


ii.

This mechanism closes the circuit when the connector is disconnected by bringing the short spring into contact with the terminals and insulating the circuit from external power sources to prevent accidental airbag activation.



b.

Releasing of activation prevention mechanism

i.

To release the activation prevention mechanism, insert a piece of paper with the same thickness as the male terminal (approximately 0.5 mm (0.0197 in.)) between the terminals and short spring to break the connection.


ii.

Refer to the following illustrations concerning connectors utilizing the activation prevention mechanism and its release method.

CAUTION:

Never release the activation prevention mechanism on the squib connector even when inspecting with the squib disconnected.


NOTICE:
·

Do not release the activation prevention mechanism unless specially directed by the troubleshooting procedure.

·

To prevent the terminal and short spring from being damaged, always use a piece of paper with the same thickness as the male terminal.



C247058E20
2.802,2.781 3.188,2.26 3.188,2.26 2.781,2.479 false 2.198,2.885 1.813,3.292 1.813,3.292 2.198,2.573 true 5.198,2.573 4.75,3.313 4.75,3.313 5.198,2.885 true 5.656,2.781 6.125,2.229 6.125,2.229 5.677,2.479 false 6.438,4.708 6.51,4.354 6.51,4.354 6.573,4.354 false 4.188,4.719 4.313,4.323 4.313,4.323 4.375,4.323 false 5.635,4.667 5.635,5.427 true 3.448,4.677 3.448,5.427 true 3.875,6.51 3.792,6.51 3.792,6.51 3.667,6.854 false 3.125,7 3.313,7.354 3.313,7.354 3.385,7.354 true 6.594,6.5 6.5,6.5 6.5,6.5 6.385,6.844 false 5.844,7 6.021,7.354 6.021,7.354 6.104,7.354 true 0.167,0.083 3.698,0.344 3.531,0.26 10 false Wire harness connector (to Airbag Sensor Assembly): 1.552,1.875 2.646,2.25 1.094,0.375 10 false Before Release 4.573,1.875 5.552,2.26 0.979,0.385 10 false After Release 3.229,2.177 3.844,2.417 0.615,0.24 10 false Paper 6.167,2.156 6.708,2.594 0.542,0.438 10 false Paper 1.427,3.302 2.635,3.583 1.208,0.281 10 false Short Spring 4.354,3.344 5.333,3.688 0.979,0.344 10 false Short Spring 3.073,4.052 4.167,4.365 1.094,0.313 10 false Before Release 2.458,6.177 3.688,6.438 1.229,0.26 10 false Before Release 5.333,4.031 6.333,4.292 1,0.26 10 false After Release 5.26,6.177 6.24,6.438 0.979,0.26 10 false After Release 3.917,6.427 4.469,6.656 0.552,0.229 10 false Paper 4.417,4.25 5.021,4.552 0.604,0.302 10 false Paper 6.583,4.26 7.083,4.552 0.5,0.292 10 false Paper 3.406,7.271 4.385,7.552 0.979,0.281 10 false Short Spring 5.24,5.479 6.302,5.802 1.063,0.323 10 false Short Spring 3.063,5.438 4.156,5.865 1.094,0.427 10 false Short Spring 6.625,6.406 7.125,6.729 0.5,0.323 10 false Paper 6.125,7.26 7.063,7.583 0.938,0.323 10 false Short Spring 0.167,3.771 3.521,4.052 3.354,0.281 10 false Spiral Cable with Sensor Sub-assembly Connector: 0.156,5.854 2.823,6.146 2.667,0.292 10 false No. 2 Instrument Panel Wire Connector: 1.073,0.469 2.656,0.792 1.583,0.323 10 false Instrument Panel Wire 3.573,0.479 4.396,0.938 0.823,0.458 10 false Floor Wire 5.208,0.469 6.375,0.677 1.167,0.208 10 false Floor Wire 0.542,7.469 1.635,7.667 1.094,0.198 10 false : Short Spring