Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278099 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1617/84  Lost Communication with Front Airbag Sensor LH  B1618/84  Front Airbag Sensor LH Initialization Incomplete  


DESCRIPTION

The front airbag sensor LH circuit consists of the airbag sensor assembly and front airbag sensor LH.

The front airbag sensor LH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbag and pretensioner should be deployed.

These DTCs are stored when a malfunction is detected in the front airbag sensor LH circuit.

DTC No. DTC Detection Condition Trouble Area
B1617/84
B1618/84
·

The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor LH circuit.

·

Front airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor LH

·

Airbag sensor assembly



WIRING DIAGRAM

C238364E81
0.552,2.917 0.823,3.083 0.271,0.167 10 false A24 0.552,3.083 2.177,3.344 1.625,0.26 10 false Front Airbag Sensor LH 5.375,2.917 5.688,3.083 0.313,0.167 10 false G18 5.375,3.083 7.01,3.333 1.635,0.25 10 false Airbag Sensor Assembly 1.51,0.865 1.844,1.042 0.333,0.177 10 false +SL 3.448,0.896 3.781,1.073 0.333,0.177 10 false AG5 5.146,0.781 5.323,0.938 0.177,0.156 10 false 30 5.146,1.958 5.323,2.115 0.177,0.156 10 false 28 1.854,0.781 1.958,0.927 0.104,0.146 10 false 2 3.552,0.667 3.656,0.813 0.104,0.146 10 false 3 3.448,2.063 3.76,2.24 0.313,0.177 10 false AG5 3.563,1.844 3.708,1.99 0.146,0.146 10 false 4 1.51,2.042 1.792,2.219 0.281,0.177 10 false -SL 5.406,0.865 5.74,1.042 0.333,0.177 10 false +SL 5.406,2.042 5.688,2.219 0.281,0.177 10 false -SL 1.854,1.958 1.958,2.104 0.104,0.146 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor LH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly and front airbag sensor LH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.




OK

2.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (OPEN)

NG

REPLACE WIRE HARNESS

2.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (OPEN)
a.
U159357E01
0.709,2.093 0.818,2.246 0.109,0.153 10 F 1.017,2.093 1.138,2.246 0.121,0.153 10 E 1.464,2.093 1.585,2.246 0.121,0.153 10 D 1.625,2.093 1.746,2.246 0.121,0.153 10 C 2.069,2.093 2.190,2.246 0.121,0.153 10 B 2.39,2.093 2.511,2.246 0.121,0.153 10 A 0.385,2.093 0.570,2.265 0.186,0.172 10 *1 2.78,2.39 2.935,2.547 0.156,0.157 10 *2 0.879,0.256 1.074,0.421 0.195,0.165 10 *a 0.373,3.192 0.540,3.346 0.167,0.155 10 *b 1.016,0.664 1.295,0.822 0.280,0.158 10 G18 1.745,1.033 2.006,1.191 0.260,0.158 10 -SL 2.697,1.033 2.991,1.191 0.294,0.158 10 +SL 0.517,3.636 0.781,3.793 0.264,0.158 10 A24 2.227,0.921 2.047,1.129 false 2.461,0.913 2.668,1.138 false 0.853,4.167 1.095,4.325 0.242,0.158 10 -SL 1.539,4.167 1.825,4.325 0.286,0.158 10 +SL 1.25,3.733 1.038,4.144 false 1.499,3.733 1.696,4.153 false 2.345,1.171 2.345,1.375 false 2.26,1.387 2.416,1.544 0.156,0.157 10 *3

Connect the connectors that link the engine room main wire and instrument panel wire.


b.

Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-2 (+SL) - A24-1 (-SL) Always Below 1 Ω


Text in Illustration
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Front Airbag Sensor LH)



OK

3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT)

NG

7.CHECK INSTRUMENT PANEL WIRE (OPEN)
3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT)
a.
U159355E01
0.662,0.599 0.771,0.751 0.109,0.153 10 F 0.971,0.599 1.092,0.751 0.121,0.153 10 E 1.414,0.599 1.535,0.751 0.121,0.153 10 D 1.568,0.599 1.689,0.751 0.121,0.153 10 C 2.023,0.599 2.144,0.751 0.121,0.153 10 B 2.339,0.599 2.460,0.751 0.121,0.153 10 A 0.358,0.599 0.542,0.777 0.184,0.178 10 *1 2.762,0.878 2.930,1.060 0.167,0.181 10 *2 0.166,1.69 0.373,1.853 0.207,0.163 10 *a 0.394,2.213 0.663,2.371 0.270,0.158 10 A24 0.844,2.812 1.104,2.970 0.260,0.158 10 -SL 1.479,2.812 1.800,2.970 0.321,0.158 10 +SL 1.225,2.358 1.036,2.782 false 1.458,2.367 1.654,2.799 false

Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-2 (+SL) - A24-1 (-SL) Always 1 MΩ or higher


Text in Illustration
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor LH)



OK

4.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO B+)

NG

8.CHECK INSTRUMENT PANEL WIRE (SHORT)
4.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO B+)
a.
U159355E01
0.662,0.599 0.771,0.751 0.109,0.153 10 F 0.971,0.599 1.092,0.751 0.121,0.153 10 E 1.414,0.599 1.535,0.751 0.121,0.153 10 D 1.568,0.599 1.689,0.751 0.121,0.153 10 C 2.023,0.599 2.144,0.751 0.121,0.153 10 B 2.339,0.599 2.460,0.751 0.121,0.153 10 A 0.358,0.599 0.542,0.777 0.184,0.178 10 *1 2.762,0.878 2.930,1.060 0.167,0.181 10 *2 0.166,1.69 0.373,1.853 0.207,0.163 10 *a 0.394,2.213 0.663,2.371 0.270,0.158 10 A24 0.844,2.812 1.104,2.970 0.260,0.158 10 -SL 1.479,2.812 1.800,2.970 0.321,0.158 10 +SL 1.225,2.358 1.036,2.782 false 1.458,2.367 1.654,2.799 false

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-2 (+SL) - Body ground Power switch on (IG) Below 1 V
A24-1 (-SL) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


Text in Illustration
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor LH)



OK

5.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND)

NG

9.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
5.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND)
a.
U159355E01
0.662,0.599 0.771,0.751 0.109,0.153 10 F 0.971,0.599 1.092,0.751 0.121,0.153 10 E 1.414,0.599 1.535,0.751 0.121,0.153 10 D 1.568,0.599 1.689,0.751 0.121,0.153 10 C 2.023,0.599 2.144,0.751 0.121,0.153 10 B 2.339,0.599 2.460,0.751 0.121,0.153 10 A 0.358,0.599 0.542,0.777 0.184,0.178 10 *1 2.762,0.878 2.930,1.060 0.167,0.181 10 *2 0.166,1.69 0.373,1.853 0.207,0.163 10 *a 0.394,2.213 0.663,2.371 0.270,0.158 10 A24 0.844,2.812 1.104,2.970 0.260,0.158 10 -SL 1.479,2.812 1.800,2.970 0.321,0.158 10 +SL 1.225,2.358 1.036,2.782 false 1.458,2.367 1.654,2.799 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-2 (+SL) - Body ground Always 1 MΩ or higher
A24-1 (-SL) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor LH)



OK

6.CHECK FRONT AIRBAG SENSOR LH

NG

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
6.CHECK FRONT AIRBAG SENSOR LH
a.
C238211E01
2.195,0.812 2.316,0.967 0.121,0.156 10 A 2.036,0.812 2.157,0.967 0.121,0.156 10 B 1.581,0.812 1.703,0.967 0.121,0.156 10 C 1.425,0.812 1.546,0.967 0.121,0.156 10 D 0.98,0.812 1.101,0.967 0.121,0.156 10 E 0.829,0.812 0.950,0.967 0.121,0.156 10 F 0.514,0.812 0.698,0.989 0.184,0.178 10 *1 2.585,1.092 2.752,1.238 0.167,0.146 10 *2

Connect the connector to the airbag sensor assembly.


b.

Interchange the front airbag sensor LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs B1612/83, B1613/83, B1617/84 and B1618/84 are not output. A
DTC B1617/84 or B1618/84 is output. B
DTC B1612/83 or B1613/83 is output. C


HINT:

Codes other than DTCs B1612/83, B1613/83, B1617/84 and B1618/84, may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the front airbag sensor LH and RH to their original positions and connect the connectors.

Text in Illustration
*1 Front Airbag Sensor RH
*2 Airbag Sensor Assembly



A

B

C

7.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
U159455E01
0.577,3.652 0.898,3.810 0.321,0.158 10 AG5 1.802,4.179 2.079,4.336 0.277,0.158 10 +SL 0.978,4.179 1.222,4.336 0.244,0.158 10 -SL 1.626,3.794 1.933,4.149 false 1.437,3.794 1.13,4.149 false 0.352,3.175 0.555,3.327 0.203,0.152 10 *b 0.587,2.099 0.696,2.251 0.109,0.153 10 F 0.896,2.099 1.017,2.251 0.121,0.153 10 E 1.34,2.099 1.461,2.251 0.121,0.153 10 D 1.657,2.099 1.777,2.251 0.121,0.153 10 C 2.112,2.099 2.233,2.251 0.121,0.153 10 B 2.425,2.099 2.546,2.251 0.121,0.153 10 A 1.058,0.61 1.347,0.768 0.288,0.158 10 G18 1.785,1.054 2.046,1.211 0.261,0.158 10 -SL 2.73,1.054 3.051,1.211 0.321,0.158 10 +SL 2.267,0.925 2.087,1.133 false 2.495,0.924 2.701,1.15 false 2.773,2.393 2.977,2.546 0.203,0.152 10 *2 1.09,2.482 1.293,2.634 0.203,0.152 10 *3 0.316,2.099 0.519,2.251 0.203,0.152 10 *1 0.902,0.261 1.106,0.413 0.203,0.152 10 *a 1.182,2.256 1.182,2.472 false 1.867,2.482 2.070,2.634 0.203,0.152 10 *4 1.959,2.256 1.959,2.472 false 2.375,1.171 2.375,1.357 false 2.293,1.363 2.446,1.515 0.153,0.152 10 *5

Disconnect the instrument panel wire connector from the engine room main wire.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AG5-3 (+SL) - AG5-4 (-SL) Always Below 1 Ω



c.

Disconnect the service wire from connector B.

Text in Illustration
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*5 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Engine Room Main Wire)



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

8.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
U159452E01
0.608,0.544 0.718,0.696 0.109,0.153 10 F 0.911,0.544 1.032,0.696 0.121,0.153 10 E 1.364,0.544 1.485,0.696 0.121,0.153 10 D 1.669,0.544 1.789,0.696 0.121,0.153 10 C 2.131,0.544 2.252,0.696 0.121,0.153 10 B 2.442,0.544 2.562,0.696 0.121,0.153 10 A 0.281,0.544 0.456,0.719 0.176,0.175 10 *1 2.813,0.813 2.982,0.987 0.169,0.174 10 *2 1.622,0.068 1.783,0.221 0.160,0.152 10 *4 1.109,0.968 1.304,1.120 0.195,0.152 10 *3 0.734,1.605 0.928,1.789 0.194,0.183 10 *a 0.914,2.185 1.213,2.342 0.299,0.158 10 AG5 1.127,2.822 1.392,2.980 0.265,0.158 10 -SL 2.293,2.822 2.591,2.980 0.299,0.158 10 +SL 1.768,2.495 1.312,2.805 false 1.995,2.495 2.451,2.805 false 1.196,0.695 1.196,0.954 false 1.955,0.554 1.955,0.154 1.955,0.154 1.804,0.154 false

Disconnect the instrument panel wire connector from the engine room main wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AG5-3 (+SL) - AG5-4 (-SL) Always 1 MΩ or higher


Text in Illustration
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

9.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
U159452E01
0.608,0.544 0.718,0.696 0.109,0.153 10 F 0.911,0.544 1.032,0.696 0.121,0.153 10 E 1.364,0.544 1.485,0.696 0.121,0.153 10 D 1.669,0.544 1.789,0.696 0.121,0.153 10 C 2.131,0.544 2.252,0.696 0.121,0.153 10 B 2.442,0.544 2.562,0.696 0.121,0.153 10 A 0.281,0.544 0.456,0.719 0.176,0.175 10 *1 2.813,0.813 2.982,0.987 0.169,0.174 10 *2 1.622,0.068 1.783,0.221 0.160,0.152 10 *4 1.109,0.968 1.304,1.120 0.195,0.152 10 *3 0.734,1.605 0.928,1.789 0.194,0.183 10 *a 0.914,2.185 1.213,2.342 0.299,0.158 10 AG5 1.127,2.822 1.392,2.980 0.265,0.158 10 -SL 2.293,2.822 2.591,2.980 0.299,0.158 10 +SL 1.768,2.495 1.312,2.805 false 1.995,2.495 2.451,2.805 false 1.196,0.695 1.196,0.954 false 1.955,0.554 1.955,0.154 1.955,0.154 1.804,0.154 false

Disconnect the instrument panel wire connector from the engine room main wire.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
AG5-3 (+SL) - Body ground Power switch on (IG) Below 1 V
AG5-4 (-SL) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
U159452E01
0.608,0.544 0.718,0.696 0.109,0.153 10 F 0.911,0.544 1.032,0.696 0.121,0.153 10 E 1.364,0.544 1.485,0.696 0.121,0.153 10 D 1.669,0.544 1.789,0.696 0.121,0.153 10 C 2.131,0.544 2.252,0.696 0.121,0.153 10 B 2.442,0.544 2.562,0.696 0.121,0.153 10 A 0.281,0.544 0.456,0.719 0.176,0.175 10 *1 2.813,0.813 2.982,0.987 0.169,0.174 10 *2 1.622,0.068 1.783,0.221 0.160,0.152 10 *4 1.109,0.968 1.304,1.120 0.195,0.152 10 *3 0.734,1.605 0.928,1.789 0.194,0.183 10 *a 0.914,2.185 1.213,2.342 0.299,0.158 10 AG5 1.127,2.822 1.392,2.980 0.265,0.158 10 -SL 2.293,2.822 2.591,2.980 0.299,0.158 10 +SL 1.768,2.495 1.312,2.805 false 1.995,2.495 2.451,2.805 false 1.196,0.695 1.196,0.954 false 1.955,0.554 1.955,0.154 1.955,0.154 1.804,0.154 false

Disconnect the instrument panel wire connector from the engine room main wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AG5-3 (+SL) - Body ground Always 1 MΩ or higher
AG5-4 (-SL) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE