Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278099 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1622/81  Lost communication with Side Airbag Sensor RH  B1623/81  Side Airbag Sensor Assembly RH Initialization Incomplete  B1632/81  Lost Communication with Rear Airbag Sensor RH  B1633/81  Rear Airbag Sensor Assembly RH Initialization Incomplete  B1642/81  Lost Communication with Side Satellite Sensor Bus RH  


DESCRIPTION

The side collision sensor RH circuit (to determine deployment of the front seat airbag assembly RH and curtain shield airbag assembly RH) is composed of the airbag sensor assembly, side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.

The side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.

These DTCs are stored when a malfunction is detected for the side collision sensor RH circuit.

DTC No. DTC Detection Condition Trouble Area
B1622/81
B1623/81
B1632/81
B1633/81
B1642/81
·

The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor RH circuit.

·

Side airbag sensor assembly RH malfunction

·

Side No. 2 airbag sensor assembly RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Side airbag sensor assembly RH

·

Side No. 2 airbag sensor assembly RH

·

Airbag sensor assembly



WIRING DIAGRAM

C239250E90
0.552,4.698 0.854,4.844 0.302,0.146 10 false M25 0.552,4.875 1.781,5.208 1.229,0.333 10 false Side Airbag Sensor Assembly RH 3.042,4.875 4.51,5.219 1.469,0.344 10 false Side No. 2 Airbag Sensor Assembly RH 3.042,4.698 3.344,4.844 0.302,0.146 10 false M27 5.24,4.844 6.833,5.042 1.594,0.198 10 false Airbag Sensor Assembly 5.24,4.667 5.604,4.833 0.365,0.167 10 false M37 1.125,0.896 1.521,1.052 0.396,0.156 10 false BBR+ 1.583,0.792 1.688,0.948 0.104,0.156 10 false 4 1.156,1.792 1.521,1.948 0.365,0.156 10 false BBR- 5.563,0.896 5.958,1.052 0.396,0.156 10 false BBR+ 5.365,0.792 5.542,0.948 0.177,0.156 10 false 8 5.323,1.698 5.5,1.854 0.177,0.156 10 false 11 5.563,1.792 5.958,1.948 0.396,0.156 10 false BBR- 1.583,1.698 1.688,1.854 0.104,0.156 10 false 3 1.125,3.042 1.521,3.198 0.396,0.156 10 false BCR+ 1.583,2.948 1.688,3.104 0.104,0.156 10 false 1 2.927,3.833 3.031,3.99 0.104,0.156 10 false 1 1.146,3.938 1.521,4.094 0.375,0.156 10 false BCR- 3.073,3.042 3.469,3.198 0.396,0.156 10 false BCR+ 3.073,3.938 3.469,4.094 0.396,0.156 10 false BCR- 1.583,3.833 1.688,3.99 0.104,0.156 10 false 2 2.927,2.948 3.031,3.104 0.104,0.156 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK CURRENT DTC
a.

Check for current DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
Current DTC B1642 or 81 is output. A
Current DTC B1623 is output. B
Current DTC B1632 or B1633 is output. C
Current DTC B1622 is output. D
Current DTCs B1622, B1623, B1632, B1633, B1642 and 81 are not output. E


HINT:
·

DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the power switch off and then on (IG) again.

·

Codes other than current DTCs B1622, B1623, B1632, B1633, B1642 and 81 may be output at this time, but they are not related to this check.





A

2.CHECK CONNECTORS

B

13.CHECK HISTORY DTC

C

20.CHECK CONNECTORS

D

27.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

E

2.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.




OK

3.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (OPEN)
a.
U159358E02
1.76,3.771 2.135,4.208 true 1.656,3.771 1.281,4.208 true 1.604,2.49 1.604,2 1.604,2 1.448,2 false 1.865,0.844 1.5,1.115 false 2.073,0.625 2.427,1.115 true 2,1.073 2,1.25 false 1.021,2.469 1.146,2.625 0.125,0.156 10 false D 1.333,2.469 1.458,2.625 0.125,0.156 10 false C 1.781,2.469 1.906,2.625 0.125,0.156 10 false B 2.094,2.469 2.219,2.625 0.125,0.156 10 false A 0.708,2.448 0.865,2.625 0.156,0.177 10 false *1 2.573,2.125 2.729,2.281 0.156,0.156 10 false *2 0.813,0.208 0.99,0.365 0.177,0.156 10 false *a 0.385,3.198 0.583,3.375 0.198,0.177 10 false *b 1.281,1.125 1.635,1.281 0.354,0.156 10 false BBR- 2.26,1.125 2.656,1.281 0.396,0.156 10 false BBR+ 1.167,0.563 1.458,0.719 0.292,0.156 10 false M37 0.573,3.656 0.865,3.813 0.292,0.156 10 false M25 1.938,4.219 2.333,4.375 0.396,0.156 10 false BBR+ 1.063,4.219 1.427,4.375 0.365,0.156 10 false BBR- 1.25,1.917 1.427,2.083 0.177,0.167 10 false *3 1.927,1.271 2.083,1.427 0.156,0.156 10 false *4

Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-4 (BBR+) - M25-3 (BBR-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.

Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



OK

4.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (SHORT)
a.
U159359E01
0.955,0.93 1.076,1.083 0.121,0.153 10 D 1.271,0.93 1.392,1.083 0.121,0.153 10 C 1.72,0.93 1.841,1.083 0.121,0.153 10 B 2.041,0.93 2.162,1.083 0.121,0.153 10 A 0.641,0.93 0.793,1.111 0.151,0.181 10 *1 2.437,0.64 2.641,0.792 0.204,0.152 10 *2 1.131,0.259 1.310,0.412 0.179,0.152 10 *3 0.334,1.749 0.568,1.925 0.234,0.175 10 *a 0.458,2.306 0.747,2.464 0.289,0.158 10 M25 1.027,2.844 1.383,3.002 0.356,0.158 10 BBR- 1.716,2.844 2.115,3.002 0.399,0.158 10 BBR+ 1.507,2.453 1.263,2.825 false 1.685,2.453 1.929,2.825 false 1.555,0.943 1.555,0.346 1.555,0.346 1.327,0.346 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-4 (BBR+) - M25-3 (BBR-) Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



OK

5.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (SHORT TO B+)
a.
U159359E01
0.955,0.93 1.076,1.083 0.121,0.153 10 D 1.271,0.93 1.392,1.083 0.121,0.153 10 C 1.72,0.93 1.841,1.083 0.121,0.153 10 B 2.041,0.93 2.162,1.083 0.121,0.153 10 A 0.641,0.93 0.793,1.111 0.151,0.181 10 *1 2.437,0.64 2.641,0.792 0.204,0.152 10 *2 1.131,0.259 1.310,0.412 0.179,0.152 10 *3 0.334,1.749 0.568,1.925 0.234,0.175 10 *a 0.458,2.306 0.747,2.464 0.289,0.158 10 M25 1.027,2.844 1.383,3.002 0.356,0.158 10 BBR- 1.716,2.844 2.115,3.002 0.399,0.158 10 BBR+ 1.507,2.453 1.263,2.825 false 1.685,2.453 1.929,2.825 false 1.555,0.943 1.555,0.346 1.555,0.346 1.327,0.346 false

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M25-4 (BBR+) - Body ground Power switch on (IG) Below 1 V
M25-3 (BBR-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



OK

6.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

6.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
U159359E01
0.955,0.93 1.076,1.083 0.121,0.153 10 D 1.271,0.93 1.392,1.083 0.121,0.153 10 C 1.72,0.93 1.841,1.083 0.121,0.153 10 B 2.041,0.93 2.162,1.083 0.121,0.153 10 A 0.641,0.93 0.793,1.111 0.151,0.181 10 *1 2.437,0.64 2.641,0.792 0.204,0.152 10 *2 1.131,0.259 1.310,0.412 0.179,0.152 10 *3 0.334,1.749 0.568,1.925 0.234,0.175 10 *a 0.458,2.306 0.747,2.464 0.289,0.158 10 M25 1.027,2.844 1.383,3.002 0.356,0.158 10 BBR- 1.716,2.844 2.115,3.002 0.399,0.158 10 BBR+ 1.507,2.453 1.263,2.825 false 1.685,2.453 1.929,2.825 false 1.555,0.943 1.555,0.346 1.555,0.346 1.327,0.346 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-4 (BBR+) - Body ground Always 1 MΩ or higher
M25-3 (BBR-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



OK

7.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

7.CHECK FLOOR WIRE (OPEN)
a.
U183616E02
1.646,3.708 1.281,4.063 false 1.802,3.708 2.177,4.063 false 1.833,0.667 1.573,1.01 false 1.948,0.667 2.208,1.01 false 1.729,4.125 1.729,4.292 false 1.708,2.271 1.708,1.75 1.708,1.75 1.49,1.75 false 1.052,2.25 1.177,2.406 0.125,0.156 10 false D 1.354,2.25 1.479,2.406 0.125,0.156 10 false C 1.958,2.25 2.083,2.406 0.125,0.156 10 false B 2.271,2.25 2.396,2.406 0.125,0.156 10 false A 0.667,2.229 0.813,2.385 0.146,0.156 10 false *1 2.573,2.26 2.74,2.438 0.167,0.177 10 false *2 1.052,4.083 1.417,4.24 0.365,0.156 10 false BCR- 1.958,4.083 2.365,4.24 0.406,0.156 10 false BCR+ 0.625,3.656 0.927,3.813 0.302,0.156 10 false M27 1.021,0.604 1.313,0.76 0.292,0.156 10 false M25 2.01,1.021 2.385,1.177 0.375,0.156 10 false BCR- 1.313,1.021 1.719,1.177 0.406,0.156 10 false BCR+ 1.292,1.667 1.448,1.813 0.156,0.146 10 false *3 0.813,0.146 1.01,0.354 0.198,0.208 10 false *a 0.448,3.167 0.646,3.375 0.198,0.208 10 false *b 1.656,4.313 1.802,4.469 0.146,0.156 10 false *4

Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - M25-2 (BCR-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.

Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)



OK

8.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

8.CHECK FLOOR WIRE (SHORT)
a.
U159360E01
1.142,0.718 1.263,0.871 0.121,0.153 10 D 1.457,0.718 1.577,0.871 0.121,0.153 10 C 1.907,0.718 2.028,0.871 0.121,0.153 10 B 2.22,0.718 2.340,0.871 0.121,0.153 10 A 0.803,0.718 0.985,0.873 0.183,0.155 10 *1 2.463,0.718 2.636,0.874 0.173,0.156 10 *2 1.372,0.116 1.545,0.268 0.172,0.152 10 *3 0.993,1.873 1.181,2.025 0.188,0.151 10 *a 1.166,2.317 1.459,2.474 0.293,0.158 10 M25 2.278,2.865 2.666,3.023 0.387,0.158 10 BCR- 1.595,2.865 1.991,3.023 0.396,0.158 10 BCR+ 2.102,2.46 1.853,2.842 false 2.227,2.46 2.476,2.842 false 1.738,0.73 1.738,0.195 1.738,0.195 1.576,0.195 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - M25-2 (BCR-) Always 1 MΩ or higher


Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



OK

9.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

9.CHECK FLOOR WIRE (SHORT TO B+)
a.
U159360E01
1.142,0.718 1.263,0.871 0.121,0.153 10 D 1.457,0.718 1.577,0.871 0.121,0.153 10 C 1.907,0.718 2.028,0.871 0.121,0.153 10 B 2.22,0.718 2.340,0.871 0.121,0.153 10 A 0.803,0.718 0.985,0.873 0.183,0.155 10 *1 2.463,0.718 2.636,0.874 0.173,0.156 10 *2 1.372,0.116 1.545,0.268 0.172,0.152 10 *3 0.993,1.873 1.181,2.025 0.188,0.151 10 *a 1.166,2.317 1.459,2.474 0.293,0.158 10 M25 2.278,2.865 2.666,3.023 0.387,0.158 10 BCR- 1.595,2.865 1.991,3.023 0.396,0.158 10 BCR+ 2.102,2.46 1.853,2.842 false 2.227,2.46 2.476,2.842 false 1.738,0.73 1.738,0.195 1.738,0.195 1.576,0.195 false

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - Body ground Power switch on (IG) Below 1 V
M25-2 (BCR-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



OK

10.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

10.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
U159360E01
1.142,0.718 1.263,0.871 0.121,0.153 10 D 1.457,0.718 1.577,0.871 0.121,0.153 10 C 1.907,0.718 2.028,0.871 0.121,0.153 10 B 2.22,0.718 2.340,0.871 0.121,0.153 10 A 0.803,0.718 0.985,0.873 0.183,0.155 10 *1 2.463,0.718 2.636,0.874 0.173,0.156 10 *2 1.372,0.116 1.545,0.268 0.172,0.152 10 *3 0.993,1.873 1.181,2.025 0.188,0.151 10 *a 1.166,2.317 1.459,2.474 0.293,0.158 10 M25 2.278,2.865 2.666,3.023 0.387,0.158 10 BCR- 1.595,2.865 1.991,3.023 0.396,0.158 10 BCR+ 2.102,2.46 1.853,2.842 false 2.227,2.46 2.476,2.842 false 1.738,0.73 1.738,0.195 1.738,0.195 1.576,0.195 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - Body ground Always 1 MΩ or higher
M25-2 (BCR-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



OK

11.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

NG

REPLACE FLOOR WIRE

11.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218E01
0.793,1.142 0.979,1.302 0.186,0.159 10 *1 2.307,0.855 2.493,1.014 0.186,0.159 10 *2 1.718,1.142 1.861,1.293 0.143,0.151 10 B 1.873,1.142 2.016,1.293 0.143,0.151 10 A 1.257,1.142 1.400,1.293 0.143,0.151 10 C 1.1,1.142 1.243,1.293 0.143,0.151 10 D

Connect the connectors to the side No. 2 airbag sensor assembly RH and airbag sensor assembly.


b.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG), and wait for at least 60 seconds.



f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1642 or 81 is output. A
DTC B1647 or 82 is output. B
DTCs B1642, B1647, 81 and 82 are not output. C


HINT:

Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.

Text in Illustration
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly



A

12.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

B

C

12.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH
a.
C238223E01
0.969,0.972 1.119,1.124 0.150,0.152 10 *1 2.271,0.972 2.420,1.124 0.150,0.152 10 *2 2.036,0.972 2.163,1.137 0.128,0.166 10 A 1.883,0.972 2.011,1.137 0.128,0.166 10 B 1.425,0.972 1.552,1.137 0.128,0.166 10 C 1.268,0.972 1.396,1.137 0.128,0.166 10 D

Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG), and wait for at least 60 seconds.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs B1642, B1647, 81 and 82 are not output. A
DTC B1642 or 81 is output. B
DTC B1647 or 82 is output. C


HINT:

Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.

Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly RH



A

B

C

REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

13.CHECK HISTORY DTC
a.

Check for history DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
History DTC B1622 is not output. A
History DTC B1622 is output. B


HINT:

Codes other than history DTC B1622 may be output at this time, but they are not related to this check.




A

14.CHECK CONNECTORS

B

27.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
14.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and side airbag sensor assembly RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly and side airbag sensor assembly RH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.




OK

15.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

15.CHECK FLOOR WIRE (OPEN)
a.
U159358E02
1.76,3.771 2.135,4.208 true 1.656,3.771 1.281,4.208 true 1.604,2.49 1.604,2 1.604,2 1.448,2 false 1.865,0.844 1.5,1.115 false 2.073,0.625 2.427,1.115 true 2,1.073 2,1.25 false 1.021,2.469 1.146,2.625 0.125,0.156 10 false D 1.333,2.469 1.458,2.625 0.125,0.156 10 false C 1.781,2.469 1.906,2.625 0.125,0.156 10 false B 2.094,2.469 2.219,2.625 0.125,0.156 10 false A 0.708,2.448 0.865,2.625 0.156,0.177 10 false *1 2.573,2.125 2.729,2.281 0.156,0.156 10 false *2 0.813,0.208 0.99,0.365 0.177,0.156 10 false *a 0.385,3.198 0.583,3.375 0.198,0.177 10 false *b 1.281,1.125 1.635,1.281 0.354,0.156 10 false BBR- 2.26,1.125 2.656,1.281 0.396,0.156 10 false BBR+ 1.167,0.563 1.458,0.719 0.292,0.156 10 false M37 0.573,3.656 0.865,3.813 0.292,0.156 10 false M25 1.938,4.219 2.333,4.375 0.396,0.156 10 false BBR+ 1.063,4.219 1.427,4.375 0.365,0.156 10 false BBR- 1.25,1.917 1.427,2.083 0.177,0.167 10 false *3 1.927,1.271 2.083,1.427 0.156,0.156 10 false *4

Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-4 (BBR+) - M25-3 (BBR-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.

Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



OK

16.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

16.CHECK FLOOR WIRE (SHORT)
a.
U159359E01
0.955,0.93 1.076,1.083 0.121,0.153 10 D 1.271,0.93 1.392,1.083 0.121,0.153 10 C 1.72,0.93 1.841,1.083 0.121,0.153 10 B 2.041,0.93 2.162,1.083 0.121,0.153 10 A 0.641,0.93 0.793,1.111 0.151,0.181 10 *1 2.437,0.64 2.641,0.792 0.204,0.152 10 *2 1.131,0.259 1.310,0.412 0.179,0.152 10 *3 0.334,1.749 0.568,1.925 0.234,0.175 10 *a 0.458,2.306 0.747,2.464 0.289,0.158 10 M25 1.027,2.844 1.383,3.002 0.356,0.158 10 BBR- 1.716,2.844 2.115,3.002 0.399,0.158 10 BBR+ 1.507,2.453 1.263,2.825 false 1.685,2.453 1.929,2.825 false 1.555,0.943 1.555,0.346 1.555,0.346 1.327,0.346 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-4 (BBR+) - M25-3 (BBR-) Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



OK

17.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

17.CHECK FLOOR WIRE (SHORT TO B+)
a.
U159359E01
0.955,0.93 1.076,1.083 0.121,0.153 10 D 1.271,0.93 1.392,1.083 0.121,0.153 10 C 1.72,0.93 1.841,1.083 0.121,0.153 10 B 2.041,0.93 2.162,1.083 0.121,0.153 10 A 0.641,0.93 0.793,1.111 0.151,0.181 10 *1 2.437,0.64 2.641,0.792 0.204,0.152 10 *2 1.131,0.259 1.310,0.412 0.179,0.152 10 *3 0.334,1.749 0.568,1.925 0.234,0.175 10 *a 0.458,2.306 0.747,2.464 0.289,0.158 10 M25 1.027,2.844 1.383,3.002 0.356,0.158 10 BBR- 1.716,2.844 2.115,3.002 0.399,0.158 10 BBR+ 1.507,2.453 1.263,2.825 false 1.685,2.453 1.929,2.825 false 1.555,0.943 1.555,0.346 1.555,0.346 1.327,0.346 false

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M25-4 (BBR+) - Body ground Power switch on (IG) Below 1 V
M25-3 (BBR-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



OK

18.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

18.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
U159359E01
0.955,0.93 1.076,1.083 0.121,0.153 10 D 1.271,0.93 1.392,1.083 0.121,0.153 10 C 1.72,0.93 1.841,1.083 0.121,0.153 10 B 2.041,0.93 2.162,1.083 0.121,0.153 10 A 0.641,0.93 0.793,1.111 0.151,0.181 10 *1 2.437,0.64 2.641,0.792 0.204,0.152 10 *2 1.131,0.259 1.310,0.412 0.179,0.152 10 *3 0.334,1.749 0.568,1.925 0.234,0.175 10 *a 0.458,2.306 0.747,2.464 0.289,0.158 10 M25 1.027,2.844 1.383,3.002 0.356,0.158 10 BBR- 1.716,2.844 2.115,3.002 0.399,0.158 10 BBR+ 1.507,2.453 1.263,2.825 false 1.685,2.453 1.929,2.825 false 1.555,0.943 1.555,0.346 1.555,0.346 1.327,0.346 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-4 (BBR+) - Body ground Always 1 MΩ or higher
M25-3 (BBR-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



OK

19.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

NG

REPLACE FLOOR WIRE

19.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218E01
0.793,1.142 0.979,1.302 0.186,0.159 10 *1 2.307,0.855 2.493,1.014 0.186,0.159 10 *2 1.718,1.142 1.861,1.293 0.143,0.151 10 B 1.873,1.142 2.016,1.293 0.143,0.151 10 A 1.257,1.142 1.400,1.293 0.143,0.151 10 C 1.1,1.142 1.243,1.293 0.143,0.151 10 D

Connect the connector to the airbag sensor assembly.


b.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG), and wait for at least 60 seconds.



f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs B1623 and B1628 are not output. A
DTC B1623 is output. B
DTC B1628 is output. C


HINT:

Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.

Text in Illustration
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly



A

B

C

20.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.




OK

21.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

21.CHECK FLOOR WIRE (OPEN)
a.
U183616E02
1.646,3.708 1.281,4.063 false 1.802,3.708 2.177,4.063 false 1.833,0.667 1.573,1.01 false 1.948,0.667 2.208,1.01 false 1.729,4.125 1.729,4.292 false 1.708,2.271 1.708,1.75 1.708,1.75 1.49,1.75 false 1.052,2.25 1.177,2.406 0.125,0.156 10 false D 1.354,2.25 1.479,2.406 0.125,0.156 10 false C 1.958,2.25 2.083,2.406 0.125,0.156 10 false B 2.271,2.25 2.396,2.406 0.125,0.156 10 false A 0.667,2.229 0.813,2.385 0.146,0.156 10 false *1 2.573,2.26 2.74,2.438 0.167,0.177 10 false *2 1.052,4.083 1.417,4.24 0.365,0.156 10 false BCR- 1.958,4.083 2.365,4.24 0.406,0.156 10 false BCR+ 0.625,3.656 0.927,3.813 0.302,0.156 10 false M27 1.021,0.604 1.313,0.76 0.292,0.156 10 false M25 2.01,1.021 2.385,1.177 0.375,0.156 10 false BCR- 1.313,1.021 1.719,1.177 0.406,0.156 10 false BCR+ 1.292,1.667 1.448,1.813 0.156,0.146 10 false *3 0.813,0.146 1.01,0.354 0.198,0.208 10 false *a 0.448,3.167 0.646,3.375 0.198,0.208 10 false *b 1.656,4.313 1.802,4.469 0.146,0.156 10 false *4

Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - M25-2 (BCR-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.

Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)



OK

22.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

22.CHECK FLOOR WIRE (SHORT)
a.
U159360E01
1.142,0.718 1.263,0.871 0.121,0.153 10 D 1.457,0.718 1.577,0.871 0.121,0.153 10 C 1.907,0.718 2.028,0.871 0.121,0.153 10 B 2.22,0.718 2.340,0.871 0.121,0.153 10 A 0.803,0.718 0.985,0.873 0.183,0.155 10 *1 2.463,0.718 2.636,0.874 0.173,0.156 10 *2 1.372,0.116 1.545,0.268 0.172,0.152 10 *3 0.993,1.873 1.181,2.025 0.188,0.151 10 *a 1.166,2.317 1.459,2.474 0.293,0.158 10 M25 2.278,2.865 2.666,3.023 0.387,0.158 10 BCR- 1.595,2.865 1.991,3.023 0.396,0.158 10 BCR+ 2.102,2.46 1.853,2.842 false 2.227,2.46 2.476,2.842 false 1.738,0.73 1.738,0.195 1.738,0.195 1.576,0.195 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - M25-2 (BCR-) Always 1 MΩ or higher


Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



OK

23.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

23.CHECK FLOOR WIRE (SHORT TO B+)
a.
U159360E01
1.142,0.718 1.263,0.871 0.121,0.153 10 D 1.457,0.718 1.577,0.871 0.121,0.153 10 C 1.907,0.718 2.028,0.871 0.121,0.153 10 B 2.22,0.718 2.340,0.871 0.121,0.153 10 A 0.803,0.718 0.985,0.873 0.183,0.155 10 *1 2.463,0.718 2.636,0.874 0.173,0.156 10 *2 1.372,0.116 1.545,0.268 0.172,0.152 10 *3 0.993,1.873 1.181,2.025 0.188,0.151 10 *a 1.166,2.317 1.459,2.474 0.293,0.158 10 M25 2.278,2.865 2.666,3.023 0.387,0.158 10 BCR- 1.595,2.865 1.991,3.023 0.396,0.158 10 BCR+ 2.102,2.46 1.853,2.842 false 2.227,2.46 2.476,2.842 false 1.738,0.73 1.738,0.195 1.738,0.195 1.576,0.195 false

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - Body ground Power switch on (IG) Below 1 V
M25-2 (BCR-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



OK

24.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

24.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
U159360E01
1.142,0.718 1.263,0.871 0.121,0.153 10 D 1.457,0.718 1.577,0.871 0.121,0.153 10 C 1.907,0.718 2.028,0.871 0.121,0.153 10 B 2.22,0.718 2.340,0.871 0.121,0.153 10 A 0.803,0.718 0.985,0.873 0.183,0.155 10 *1 2.463,0.718 2.636,0.874 0.173,0.156 10 *2 1.372,0.116 1.545,0.268 0.172,0.152 10 *3 0.993,1.873 1.181,2.025 0.188,0.151 10 *a 1.166,2.317 1.459,2.474 0.293,0.158 10 M25 2.278,2.865 2.666,3.023 0.387,0.158 10 BCR- 1.595,2.865 1.991,3.023 0.396,0.158 10 BCR+ 2.102,2.46 1.853,2.842 false 2.227,2.46 2.476,2.842 false 1.738,0.73 1.738,0.195 1.738,0.195 1.576,0.195 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - Body ground Always 1 MΩ or higher
M25-2 (BCR-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



OK

25.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

NG

REPLACE FLOOR WIRE

25.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218E01
0.793,1.142 0.979,1.302 0.186,0.159 10 *1 2.307,0.855 2.493,1.014 0.186,0.159 10 *2 1.718,1.142 1.861,1.293 0.143,0.151 10 B 1.873,1.142 2.016,1.293 0.143,0.151 10 A 1.257,1.142 1.400,1.293 0.143,0.151 10 C 1.1,1.142 1.243,1.293 0.143,0.151 10 D

Connect the connector to the side No. 2 airbag sensor assembly RH.


b.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG), and wait for at least 60 seconds.



f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1632 or B1633 is output. A
DTC B1637 or B1638 is output. B
DTCs B1632, B1633, B1637 and B1638 are not output. C


HINT:

Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.

Text in Illustration
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly



A

26.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

B

C

26.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH
a.
C238223E01
0.969,0.972 1.119,1.124 0.150,0.152 10 *1 2.271,0.972 2.420,1.124 0.150,0.152 10 *2 2.036,0.972 2.163,1.137 0.128,0.166 10 A 1.883,0.972 2.011,1.137 0.128,0.166 10 B 1.425,0.972 1.552,1.137 0.128,0.166 10 C 1.268,0.972 1.396,1.137 0.128,0.166 10 D

Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG), and wait for at least 60 seconds.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs B1632, B1633, B1637 and B1638 are not output. A
DTC B1632 or B1633 is output. B
DTC B1637 or B1638 is output. C


HINT:

Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.

Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly RH



A

B

C

REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

27.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218E01
0.793,1.142 0.979,1.302 0.186,0.159 10 *1 2.307,0.855 2.493,1.014 0.186,0.159 10 *2 1.718,1.142 1.861,1.293 0.143,0.151 10 B 1.873,1.142 2.016,1.293 0.143,0.151 10 A 1.257,1.142 1.400,1.293 0.143,0.151 10 C 1.1,1.142 1.243,1.293 0.143,0.151 10 D

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.



g.

Turn the power switch off.


h.

Turn the power switch on (IG), and wait for at least 60 seconds.


i.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs B1622 and B1627 are not output. A
DTC B1622 is output. B
DTC B1627 is output. C


HINT:

Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.



j.

Turn the power switch off.


k.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



l.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.

Text in Illustration
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly



A

B

C