72211
1.INSTALL SEAT TRACK ADJUSTING HANDLE
Engage the 2 springs to install the seat track adjusting handle to the separate type front seat cushion spring assembly.
71640S
2.INSTALL SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY
Engage the 4 guides to install the separate type front seatback spring assembly to the separate type front seat cushion spring assembly.
Install the 4 bolts.
71538B
3.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH (for Driver Side)
Engage the 5 claws to install the front seat cushion edge protector LH.
71537H
4.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH (for Driver Side)
Engage the 5 claws to install the front seat cushion edge protector RH.
71538A
5.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH (for Front Passenger Side)
Engage the 5 claws to install the front seat cushion edge protector LH.
71537G
6.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH (for Front Passenger Side)
Engage the 5 claws to install the front seat cushion edge protector RH.
71874
7.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side)
Engage the clip to install the front seat lower cushion shield LH.
Engage the hook as shown in the illustration.
Install the screw.
71873
8.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Driver Side)
Engage the clip to install the front seat lower cushion shield RH.
Engage the hook as shown in the illustration.
Install the screw.
71074S
9.INSTALL SEPARATE TYPE FRONT SEATBACK COVER
Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 6 new hog rings.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
73920A
10.INSTALL FRONT SEAT AIRBAG ASSEMBLY
11.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Temporarily install the separate type front seatback cover with pad.
Engage the 4 claws to install the 2 front seat headrest supports.
Install the 3 brackets with the 2 nuts.
For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.
Make sure that the strap is not twisted after installing the nut.
Install the bracket securely.
Turn back the separate type front seatback cover.
Using hog ring pliers, install 2 new hog rings.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
Using hog ring pliers, install 3 new hog rings.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
Using hog ring pliers, install 5 new hog rings.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
71072S
12.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 18 new hog rings.
Be careful not to damage the separate type front seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.
Using hog ring pliers, install 2 new hog rings.
Be careful not to damage the separate type front seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.
13.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
Temporarily install the separate type front seat cushion cover with pad.
Engage each hook.
for Front Passenger Side:
Engage the clamp to install the connector as shown in the illustration.
73920A
14.CONNECT FRONT SEAT AIRBAG ASSEMBLY
for LH Side:
Engage the claw and 6 clamps to install the front seat airbag assembly wire harness.
for RH Side:
Engage the claw and 3 clamps to install the front seat airbag assembly wire harness.
Engage the fastener to secure the front seat airbag assembly wire harness.
71874C
15.INSTALL FRONT SEAT LOWER CUSHION SHIELD (for Driver Side)
Engage the 2 claws to install the front seat lower cushion shield.
71812D
16.INSTALL FRONT SEAT CUSHION SHIELD
Engage the 2 claws, 4 guides and clip to install the front seat cushion shield.
Install the screw.
72495
17.INSTALL VERTICAL ADJUSTING HANDLE (for Driver Side)
Install the vertical adjusting handle with the screw.
72526A
18.INSTALL RECLINING ADJUSTER RELEASE HANDLE
Engage the claw to install the reclining adjuster release handle.
71849
19.INSTALL SEAT ADJUSTER COVER CAP
Install the 2 seat adjuster cover caps.
20.INSTALL FRONT SEAT BELT ANCHOR PLATE
73240
21.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)
73230
22.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)
71862
23.INSTALL FRONT SEAT INNER CUSHION SHIELD (for LHD Driver Side)
Engage the 2 claws and 4 guides to install the front seat inner cushion shield.
71861
24.INSTALL FRONT SEAT INNER CUSHION SHIELD (for RHD Driver Side)
Engage the 2 claws and 5 guides to install the front seat inner cushion shield.
71861
25.INSTALL FRONT SEAT INNER CUSHION SHIELD (for Front Passenger Side)
Engage the 2 claws and 5 guides to install the front seat inner cushion shield.
71074S
26.CONNECT SEPARATE TYPE FRONT SEATBACK COVER
Connect the rubber band of the separate type front seatback cover.