Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM (w/o Occupant Classification System)
RM2170E _58 Vehicle Interior _057041 SEAT BELT _0278116 SEAT BELT WARNING SYSTEM U

SEAT BELT  SEAT BELT WARNING SYSTEM  TERMINALS OF ECU  


CHECK COMBINATION METER ASSEMBLY


a.

Disconnect the G1 combination meter assembly connector.

U183709E02
2.333,0.385 2.542,0.604 0.208,0.219 10 false G1 5.385,0.448 5.677,0.635 0.292,0.188 10 false G3


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
G1-20 (ET) - Body ground BR - Body ground Ground Always Below 1 Ω
G1-12 (SW) - Body ground BE - Body ground Front passenger seat belt buckle switch signal Power switch on (IG), front passenger seat occupied, front passenger seat belt fastened 10 kΩ or higher
G1-12 (SW) - Body ground BE - Body ground Front passenger seat belt buckle switch signal Power switch on (IG), front passenger seat occupied, front passenger seat belt unfastened Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the G1 combination meter assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
G1-21 (IG+) - Body ground B - Body ground Ignition power supply
(IG signal)
Power switch off Below 1 V
G1-21 (IG+) - Body ground B - Body ground Ignition power supply
(IG signal)
Power switch on (IG) 11 to 14 V

If the result is not as specified, the combination meter assembly may have a malfunction.



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


a.

Disconnect the MB main body ECU (multiplex network body ECU) connector.

U183415E02
4.052,1.031 4.052,0.625 4.052,0.625 4.167,0.625 false 1.677,1.417 1.927,1.417 false 0.729,2.677 1.042,2.677 false 1.625,0.854 1.625,0.427 1.625,0.427 1.802,0.427 false 4.219,0.552 4.448,0.688 0.229,0.135 10 false MB 3.448,7.896 3.677,8.031 0.229,0.135 10 false MB 0.396,2.531 0.76,2.688 0.365,0.156 10 false 3E*B 0.396,2.688 0.813,2.833 0.417,0.146 10 false 3F*C 5.031,5.208 5.24,5.344 0.208,0.135 10 false 3C 0.906,1.354 1.104,1.49 0.198,0.135 10 false 3D 0.146,0.094 0.344,0.229 0.198,0.135 10 false *A 5.042,3.833 5.24,3.99 0.198,0.156 10 false *B 5.615,3.833 5.813,4.01 0.198,0.177 10 false *C 1.823,5.198 2.021,5.333 0.198,0.135 10 false 3D 5.875,1.313 6.073,1.448 0.198,0.135 10 false 3B 1.823,6.563 2.021,6.698 0.198,0.135 10 false 3B 5.875,2 6.063,2.135 0.188,0.135 10 false 3A 5.083,6.563 5.271,6.698 0.188,0.135 10 false 3A 0.906,1.99 1.115,2.125 0.208,0.135 10 false 3C 1.938,1.323 2.302,1.542 0.365,0.219 10 false G59 1.833,0.344 2.125,0.479 0.292,0.135 10 false *1 5.333,3.865 5.563,4 0.229,0.135 10 false 3F 1.719,3.865 2.01,4 0.292,0.135 10 false G59 4.76,3.865 5.021,4 0.26,0.135 10 false 3E

Text in Illustration
*A Main body ECU (multiplex network body ECU) with 1 connector *B for LHD
*C for RHD - -
*1 Main body ECU (multiplex network body ECU) - -

U183433E02
1.635,0.958 1.635,0.615 1.635,0.615 1.771,0.615 false 4.094,1.146 4.094,0.635 4.094,0.635 4.229,0.635 false 1.677,1.531 1.948,1.531 false 1.677,1.958 1.948,1.958 false 0.771,2.719 1.042,2.719 false 2.219,3.792 2.5,3.948 0.281,0.156 10 false G60 4.698,3.802 4.979,3.958 0.281,0.156 10 false G59 1.156,5.063 1.438,5.219 0.281,0.156 10 false 3D 3.927,5.042 4.208,5.198 0.281,0.156 10 false 3C 1.813,6.313 2.094,6.469 0.281,0.156 10 false 3B 3.469,7.563 3.75,7.719 0.281,0.156 10 false MB 4.927,6.302 5.208,6.458 0.281,0.156 10 false 3A 5.896,5.052 6.177,5.208 0.281,0.156 10 false 3F 0.146,0.083 0.427,0.24 0.281,0.156 10 false *A 1.813,0.531 2.094,0.688 0.281,0.156 10 false *1 1.969,1.469 2.26,1.625 0.292,0.156 10 false G59 1.969,1.885 2.26,2.042 0.292,0.156 10 false G60 4.271,0.563 4.563,0.76 0.292,0.198 10 false MB 5.875,1.417 6.156,1.573 0.281,0.156 10 false 3B 5.875,2.094 6.156,2.25 0.281,0.156 10 false 3A 0.906,1.417 1.188,1.573 0.281,0.156 10 false 3D 0.906,2.094 1.188,2.25 0.281,0.156 10 false 3C 0.552,2.656 0.771,2.813 0.219,0.156 10 false 3F

Text in Illustration
*A Main body ECU (multiplex network body ECU) with 2 connectors - -
*1 Main body ECU (multiplex network body ECU) - -


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
MB-30 (BECU) - Body ground - Auxiliary battery power supply Power switch off 11 to 14 V
MB-29 (ACC) - Body ground - ACC power supply Power switch on (ACC) 11 to 14 V
MB-29 (ACC) - Body ground - ACC power supply Power switch off Below 1 V
MB-32 (IG) - Body ground - Power switch power supply Power switch on (IG) 11 to 14 V
MB-32 (IG) - Body ground - Power switch power supply Power switch off Below 1 V
MB-18 (DBKL) - Body ground - Driver seat belt buckle switch signal Driver seat belt fastened 10 kΩ or higher
MB-18 (DBKL) - Body ground - Driver seat belt buckle switch signal Driver seat belt unfastened Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.