Home › Vehicle Interior › SEAT BELT › TONGUE PLATE STOPPER
RM2170E _58 Vehicle Interior _057041 SEAT BELT _0278124 TONGUE PLATE STOPPER A

SEAT BELT  TONGUE PLATE STOPPER  REPLACEMENT  


PROCEDURE

Hide 73219 1.REMOVE TONGUE PLATE STOPPER

a.
B244166E01
2.727,0.72 2.884,0.869 0.157,0.149 10 *2 2.502,0.119 2.659,0.268 0.157,0.149 10 *1 2.254,1.229 2.412,1.378 0.157,0.149 10 *a 1.929,0.241 2.482,0.202 false 2.342,0.537 2.686,0.775 false 1.843,1.416 2.241,1.317 false

Slide the tongue plate above the installation position of the tongue plate stopper, and temporarily hold it with adhesive tape.


b.

Remove any pieces of the original tongue plate stopper in the belt webbing with a pair of pliers.

NOTICE:

Be careful not to damage the belt webbing during repair.


Text in Illustration
*1 Adhesive Tape
*2 Tongue Plate
*a Broken Tongue Plate Stopper


Hide 73219 2.INSTALL TONGUE PLATE STOPPER

a.
B245036E01
2.103,2.675 2.260,2.824 0.157,0.149 10 *2 2.808,1.827 2.965,1.976 0.157,0.149 10 *1 2.445,3.809 2.603,3.958 0.157,0.149 10 *b 1.984,4.125 2.142,4.274 0.157,0.149 10 *a 1.678,2.878 2.077,2.756 false 0.399,1.042 0.556,1.191 0.157,0.149 10 *1 2.927,4.121 3.084,4.270 0.157,0.149 10 *1 1.433,3.915 1.968,4.205 false 2.175,4.205 2.923,4.205 false 2.201,3.764 2.429,3.888 false 2.63,3.888 2.767,3.888 2.767,3.888 2.767,4.205 false 0.933,1.123 0.58,1.123 false 2.797,1.903 2.444,1.903 false

Position a new tongue plate stopper in the hole of the belt webbing.

Text in Illustration
*1 Tongue Plate Stopper
*2 Belt Webbing
*a Male
*b Female

HINT:

Make sure that the installation direction of the tongue plate stopper is as shown in the illustration.



b.
B244167E01
2.617,1.285 2.774,1.434 0.157,0.149 10 *1 2.607,1.37 2.226,1.219 false 1.222,0.53 1.380,0.679 0.157,0.149 10 *1 1.411,0.61 1.754,0.862 false

Hold the tongue plate stopper in the hole of the belt webbing using an adjustable wrench, and turn the adjustment screw of the adjustable wrench by hand to compress the tongue plate stopper.

Text in Illustration
*1 Protective Tape

NOTICE:
·

When using the adjustable wrench, make sure to position the male and female parts of the tongue plate stopper parallel to each other.

·

Do not use pliers to compress the pin of the tongue plate stopper. They may damage the tongue plate stopper and belt webbing.



HINT:

Tape the jaws of the adjustable wrench before use.



c.
B244168E24
2.302,3.854 3.177,4.167 0.875,0.313 10 false 4.5 to 5.0 mm

When the adjustment screw of the adjustable wrench cannot be turned by hand, tighten the adjustment screw using a pair of adjustable joint pliers until the tongue plate stopper thickness is 4.5 to 5.0 mm (0.177 to 0.197 in.). (Refer to the illustrations.)


d.
B245037E01
0.352,2.296 0.510,2.444 0.157,0.149 10 *b 0.352,0.337 0.510,0.485 0.157,0.149 10 *a

Make sure that the male pin of the tongue plate stopper has expanded evenly in the hole of the female part and is firmly held to the belt webbing. (Refer to the illustrations.)

Text in Illustration
*a CORRECT
*b INCORRECT