Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › 2011.12–2017.06
RM2170E _59 Vehicle Exterior _057045 WINDOW / GLASS _0278147 POWER WINDOW CONTROL SYSTEM U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  DATA LIST / ACTIVE TEST  


READ DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch to on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / D-Door Motor or Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

D-Door Motor (Power Window Regulator Motor Assembly (for Driver Door))
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door P/W Auto SW Driver door power window auto switch signal / ON or OFF ON: Driver door power window auto switch operated
OFF: Driver door power window auto switch not operated
-
D Door P/W Up SW Driver door power window manual up switch signal / ON or OFF ON: Driver door power window manual up switch operated
OFF: Driver door power window manual up switch not operated
-
D Door P/W Down SW Driver door power window manual down switch signal / ON or OFF ON: Driver door power window manual down switch operated
OFF: Driver door power window manual down switch not operated
-
Glass Position (Close - 1/4) Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open window glass position / OK or Caution OK: Normal manual up operation
Caution: Jam detected in the specified range
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
Glass Position (1/4 - 2/4) Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open window glass position / OK or Caution OK: Normal manual up operation
Caution: Jam detected in the specified range
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
Glass Position (2/4 - 3/4) Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open window glass position / OK or Caution OK: Normal manual up operation
Caution: Jam detected in the specified range
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
Glass Position (3/4 - Open) Margin for jam protection triggering force of window glass within range of 3/4 to fully open window glass position / OK or Caution OK: Normal manual up operation
Caution: Jam detected in the specified range
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
Number of Trouble Codes Number of trouble codes / Min.: 0 or Max.: 255 Number of DTCs will be displayed -

Main Body (Main Body ECU (Multiplex Network Body ECU))
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Door Courtesy Front door courtesy light switch RH / OPEN or CLOSE CLOSE: Front door RH closed
OPEN: Front door RH open
-
FL Door Courtesy Front door courtesy light switch LH / OPEN or CLOSE CLOSE: Front door LH closed
OPEN: Front door LH open
-
Communication D-Door Motor Connection status between power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU) / OK or STOP OK: Normal communication
STOP: Communication stopped
-



ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch to on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / D-Door Motor or Main Body / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


D-Door Motor (Power Window Regulator Motor Assembly (for Driver Door))
Tester Display Test Part Control Range Diagnostic Note
Power Window Power window OFF / UP / DOWN -

Main Body (Main Body ECU (Multiplex Network Body ECU))
Tester Display Test Part Control Range Diagnostic Note
IG OFF P/W Control Permission Output Power window OFF / ON Perform this Active Test with the power switch off