Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › 2011.12–2017.06
RM2170E _59 Vehicle Exterior _057045 WINDOW / GLASS _0278147 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Rear Power Window LH does not Operate with Rear Power Window Switch LH  


DESCRIPTION

When the power switch is on (IG), the power window regulator motor assembly (for rear LH door) is operated by the power window regulator switch assembly (for rear LH door).

WIRING DIAGRAM

B301257E28
4.596,2.73 6.226,3.053 1.630,0.323 10 Power Window Regulator Master Switch Assembly 2.347,2.411 4.023,2.900 1.677,0.489 10 Power Window Regulator Switch Assembly (for Rear LH Door) 0.312,2.411 1.943,2.896 1.632,0.486 10 Power Window Regulator Motor Assembly (for Rear LH Door) 4.596,2.569 5.365,2.718 0.769,0.149 10 J1*1, H1*2 2.347,2.257 2.615,2.405 0.268,0.149 10 L1 0.312,2.257 0.565,2.405 0.253,0.149 10 L2 0.732,3.433 1.504,3.582 0.772,0.149 10 *1: for LHD 1.993,3.433 2.765,3.582 0.772,0.149 10 *2: for RHD 6.207,1.906 6.317,2.055 0.111,0.149 10 E 5.24,1.265 5.351,1.414 0.111,0.149 10 B 5.401,1.073 5.512,1.222 0.111,0.149 10 6 4.385,1.696 4.517,1.845 0.132,0.149 10 U 2.727,1.598 2.859,1.747 0.132,0.149 10 U 2.555,1.598 2.686,1.747 0.132,0.149 10 4 1.354,1.598 1.486,1.747 0.132,0.149 10 U 1.518,1.598 1.649,1.747 0.132,0.149 10 1 3.222,1.696 3.442,1.845 0.220,0.149 10 SU 3.178,1.55 3.298,1.699 0.119,0.149 10 B 3.222,2.07 3.442,2.219 0.220,0.149 10 SD 4.385,2.074 4.517,2.223 0.132,0.149 10 D 2.727,1.976 2.859,2.125 0.132,0.149 10 D 2.555,1.976 2.686,2.125 0.132,0.149 10 1 1.354,1.976 1.486,2.125 0.132,0.149 10 D 1.518,1.976 1.649,2.125 0.132,0.149 10 2 3.188,1.372 3.319,1.521 0.132,0.149 10 3 3.499,1.7 3.630,1.849 0.132,0.149 10 5 3.678,1.7 4.335,1.849 0.658,0.149 10 12*1,18*2 6.372,1.906 6.900,2.055 0.528,0.149 10 1*1,9*2 3.678,2.074 4.335,2.223 0.658,0.149 10 13*1,10*2 3.499,2.078 3.630,2.227 0.132,0.149 10 2 3.965,0.54 4.293,0.689 0.328,0.149 10 P/W 1.996,1.052 2.728,1.201 0.731,0.149 10 DOOR R/L 0.308,0.365 1.370,0.514 1.062,0.149 10 from P/W Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR LH DOOR) - AUXILIARY BATTERY)
a.

Disconnect the power window regulator switch assembly (for rear LH door) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L1-3 (B) - Body ground Power switch on (IG) 11 to 14 V




OK

2.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR LH DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR LH DOOR)
a.
B164433E19
0.199,0.223 0.382,0.365 0.184,0.142 10 *a 1.387,2.713 1.522,2.855 0.135,0.142 10 U 0.981,2.713 1.192,2.855 0.211,0.142 10 SU 2.401,2.713 2.536,2.855 0.135,0.142 10 D 1.696,2.713 1.831,2.855 0.135,0.142 10 B 1.971,2.713 2.184,2.855 0.213,0.142 10 SD 2.192,2.16 2.401,2.713 false 1.938,2.16 2.063,2.713 false 1.544,2.16 1.453,2.713 false 1.301,2.16 1.109,2.713 false 1.755,2.154 1.755,2.713 false

Remove the power window regulator switch assembly (for rear LH door) (See page Vehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance when the switch is operated according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (D) - 2 (SD) UP Below 1 Ω
3 (B) - 4 (U) Below 1 Ω
1 (D) - 2 (SD) off Below 1 Ω
4 (U) - 5 (SU) Below 1 Ω
4 (U) - 5 (SU) DOWN Below 1 Ω
1 (D) - 3 (B) Below 1 Ω


Text in Illustration
*a Component without harness connected
(Power Window Regulator Switch Assembly (for Rear LH Door))



OK

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH (FOR REAR LH DOOR) - POWER WINDOW REGULATOR MOTOR LH)

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR LH DOOR)

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH (FOR REAR LH DOOR) - POWER WINDOW REGULATOR MOTOR LH)
a.

Disconnect the power window regulator motor assembly (for rear LH door) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L1-4 (U) - L2-1 (U) Always Below 1 Ω
L1-1 (D) - L2-2 (D) Always Below 1 Ω
L1-4 (U) - Body ground Always 10 kΩ or higher
L1-1 (D) - Body ground Always 10 kΩ or higher




OK

4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.
B298969E44
1.052,0.844 1.094,1.656 false 2.344,0.844 2.313,1.656 false 2.021,2.01 2.177,2.646 false 2.344,2.021 2.573,2.635 false 1.823,2.01 1.656,2.656 false 1.052,2 0.906,2.656 false 1.521,1.792 1.271,2.656 false 0.198,0.083 0.385,0.271 0.188,0.188 10 false *a 0.927,0.656 1.229,0.844 0.302,0.188 10 false E*B 2.083,2.656 2.365,2.844 0.281,0.188 10 false U*A 2.219,0.646 2.542,0.833 0.323,0.188 10 false E*A 2.479,2.635 2.781,2.823 0.302,0.188 10 false D*B 0.792,2.688 1.083,2.875 0.292,0.188 10 false U*B 1.521,2.667 1.823,2.854 0.302,0.188 10 false D*A 1.208,2.677 1.354,2.865 0.146,0.188 10 false B

Remove the power window regulator master switch assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).


b.

Measure the resistance when the switch is operated according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Switch Condition Specified Condition
6 (B) - 12 (U) UP Below 1 Ω
1 (E) - 13 (D) Below 1 Ω
1 (E) - 12 (U) off Below 1 Ω
1 (E) - 13 (D) Below 1 Ω
6 (B) - 13 (D) DOWN Below 1 Ω
1 (E) - 12 (U) Below 1 Ω

for RHD
Tester Connection Switch Condition Specified Condition
6 (B) - 18 (U) UP Below 1 Ω
9 (E) - 10 (D) Below 1 Ω
9 (E) - 18 (U) off Below 1 Ω
9 (E) - 10 (D) Below 1 Ω
6 (B) - 10 (D) DOWN Below 1 Ω
9 (E) - 18 (U) Below 1 Ω


Text in Illustration
*A for LHD
*B for RHD
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)



OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR SWITCH (FOR REAR LH DOOR))

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR SWITCH (FOR REAR LH DOOR))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
J1-12 (U) - L1-5 (SU) Always Below 1 Ω
J1-13 (D) - L1-2 (SD) Always Below 1 Ω
J1-12 (U) - Body ground Always 10 kΩ or higher
J1-13 (D) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
H1-18 (U) - L1-5 (SU) Always Below 1 Ω
H1-10 (D) - L1-2 (SD) Always Below 1 Ω
H1-18 (U) - Body ground Always 10 kΩ or higher
H1-10 (D) - Body ground Always 10 kΩ or higher




OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR