Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › 2011.12–2017.06
RM2170E _59 Vehicle Exterior _057045 WINDOW / GLASS _0278147 POWER WINDOW CONTROL SYSTEM C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  B2312  Power Window Switch Malfunction  


DESCRIPTION

The power window regulator motor assembly (for driver door) is operated by the power window regulator master switch assembly. The power window regulator motor assembly (for driver door) has motor, regulator and ECU functions.

This DTC is stored when the ECU built into the regulator motor determines that the power window regulator master switch assembly is stuck.

D-Door Motor (Power Window Regulator Motor Assembly (for Driver Door))
DTC No. DTC Detection Condition Trouble Area
B2312
·

Power window regulator master switch assembly (for driver door) stuck

·

Power window regulator master switch assembly held in same position for more than 20 seconds


·

Power window regulator master switch assembly

·

Power window regulator motor assembly (for driver door)

·

Wire harness or connector



WIRING DIAGRAM

B281016E18
0.269,2.289 2.276,2.705 2.008,0.415 10 Main Body ECU (Multiplex Network Body ECU) 0.965,3.368 2.611,3.524 1.647,0.156 10 : LIN Communication Line 0.415,0.529 1.321,0.869 0.906,0.340 10 from Auxiliary Battery 1.852,0.669 2.464,0.825 0.612,0.156 10 DOOR D 2.52,2.41 4.574,2.816 2.054,0.406 10 Power Window Regulator Motor Assembly (for Driver Door) 5.228,2.406 6.838,2.765 1.610,0.360 10 Power Window Regulator Master Switch Assembly 2.52,2.251 3.527,2.412 1.008,0.161 10 J3*1, H3*2 5.228,2.247 5.951,2.407 0.723,0.161 10 J1*1, H1*2 1.635,1.589 2.015,1.745 0.380,0.156 10 LIN2 2.833,1.449 3.095,1.605 0.262,0.156 10 LIN 2.833,0.426 2.962,0.582 0.129,0.156 10 B 3.799,0.426 4.206,0.582 0.407,0.156 10 AUTO 5.373,0.524 5.798,0.680 0.426,0.156 10 AUTO 5.373,1.033 5.507,1.189 0.134,0.156 10 D 5.373,1.528 5.507,1.684 0.134,0.156 10 U 5.373,1.832 5.507,1.988 0.134,0.156 10 E 3.724,0.93 4.238,1.086 0.514,0.156 10 DOWN 3.962,1.44 4.207,1.595 0.245,0.156 10 UP 3.87,1.729 4.237,1.885 0.367,0.156 10 GND 4.252,1.729 4.381,1.885 0.129,0.156 10 1 4.252,0.935 4.381,1.091 0.129,0.156 10 7 5.209,0.935 5.338,1.091 0.129,0.156 10 5 4.821,1.458 5.321,1.614 0.500,0.156 10 8*1,1*2 4.821,1.748 5.307,1.904 0.486,0.156 10 1*1,9*2 4.252,0.426 4.381,0.582 0.129,0.156 10 4 5.209,0.426 5.338,0.582 0.129,0.156 10 4 4.252,1.449 4.437,1.605 0.185,0.156 10 10 2.641,0.426 2.770,0.582 0.129,0.156 10 2 2.633,1.449 2.804,1.605 0.172,0.156 10 9 3.299,3.157 4.083,3.313 0.784,0.156 10 *1: for LHD 3.299,3.442 4.083,3.598 0.784,0.156 10 *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

DTC B2312 can be stored in the power window regulator motor assembly (for driver door).

·

If a power window regulator motor assembly (for driver door) has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK DTC OUTPUT

OK

END (DUE TO SWITCH BEING OPERATED FOR 20 SECONDS OR MORE)

NG

2.READ VALUE USING INTELLIGENT TESTER (DRIVER DOOR WINDOW MOTOR)
2.READ VALUE USING INTELLIGENT TESTER (DRIVER DOOR WINDOW MOTOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch to on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / D-Door Motor / Data List.


e.

Read the Data List according to the display on the intelligent tester.

D-Door Motor (Power Window Regulator Motor Assembly (for Driver Door))
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door P/W Auto SW Driver door power window auto switch signal / ON or OFF ON: Driver door power window auto switch operated
OFF: Driver door power window auto switch not operated
-
D Door P/W Up SW Driver door power window manual up switch signal / ON or OFF ON: Driver door power window manual up switch operated
OFF: Driver door power window manual up switch not operated
-
D Door P/W Down SW Driver door power window manual down switch signal / ON or OFF ON: Driver door power window manual down switch operated
OFF: Driver door power window manual down switch not operated
-

OK:

On the intelligent tester screen, ON or OFF is displayed accordingly.




OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

NG

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR (FOR DRIVER DOOR))
3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR (FOR DRIVER DOOR))
a.

Disconnect the power window regulator master switch assembly connector.


b.

Disconnect the power window regulator motor assembly (for driver door) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
J1-8 (U) - Body ground Always 10 kΩ or higher
J1-5 (D) - Body ground Always 10 kΩ or higher
J1-4 (AUTO) - Body ground Always 10 kΩ or higher
J3-10 (UP) - Body ground Always 10 kΩ or higher
J3-7 (DOWN) - Body ground Always 10 kΩ or higher
J3-4 (AUTO) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
H1-1 (U) - Body ground Always 10 kΩ or higher
H1-5 (D) - Body ground Always 10 kΩ or higher
H1-4 (AUTO) - Body ground Always 10 kΩ or higher
H3-10 (UP) - Body ground Always 10 kΩ or higher
H3-7 (DOWN) - Body ground Always 10 kΩ or higher
H3-4 (AUTO) - Body ground Always 10 kΩ or higher




OK

4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.
B298969E41
1.052,0.854 1.094,1.667 false 2.344,0.854 2.313,1.667 false 1.906,1.76 2.198,2.656 false 1.677,1.792 1.458,2.635 false 1.219,1.802 0.917,2.708 false 0.198,0.083 0.385,0.271 0.188,0.188 10 false *a 0.927,0.677 1.229,0.865 0.302,0.188 10 false E*B 2.073,2.667 2.5,2.854 0.427,0.188 10 false AUTO 2.073,0.656 2.656,0.844 0.583,0.188 10 false E*A,U*B 0.792,2.729 1.083,2.917 0.292,0.188 10 false U*A 1.396,2.667 1.552,2.854 0.156,0.188 10 false D

Remove the power window regulator master switch assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Switch Condition Specified Condition
8 (U) - 1 (E) Released 10 kΩ or higher
8 (U) - 4 (AUTO) Released 10 kΩ or higher
4 (AUTO) - 1 (E) Released 10 kΩ or higher
5 (D) - 1 (E) Released 10 kΩ or higher
4 (AUTO) - 5 (D) Released 10 kΩ or higher

for RHD
Tester Connection Switch Condition Specified Condition
1 (U) - 9 (E) Released 10 kΩ or higher
1 (U) - 4 (AUTO) Released 10 kΩ or higher
4 (AUTO) - 9 (E) Released 10 kΩ or higher
5 (D) - 9 (E) Released 10 kΩ or higher
4 (AUTO) - 5 (D) Released 10 kΩ or higher


Text in Illustration
*A for LHD
*B for RHD
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY