Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM2170E _59 Vehicle Exterior _057045 WINDOW / GLASS _0278147 POWER WINDOW CONTROL SYSTEM C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  B2311  Power Window Motor Malfunction  


DESCRIPTION

The power window regulator motor assembly (for driver door) is operated by the power window regulator master switch assembly. The power window regulator motor assembly (for driver door) has motor, regulator and ECU functions.

This DTC is stored when the power window regulator motor assembly (for driver door) has a malfunction, or the ECU built into the regulator motor assembly determines that the fully closed window position has deviated approximately 20 mm (0.787 in.) or more from the normal position.

D-Door Motor (Power Window Regulator Motor Assembly (for Driver Door))
DTC No. DTC Detection Condition Trouble Area
B2311

Either condition is met:

(a)

Power window regulator motor assembly malfunctions

(b)

When ECU in power window regulator motor assembly determines that fully closed window position has deviated approx. 20 mm (0.787 in.) or more from normal position



·

Power window regulator motor assembly (for driver door)

·

Incorrect installation of power window components

·

Overheated power window regulator motor assembly



CAUTION / NOTICE / HINT

NOTICE:
·

DTC B2311 can be stored in the power window regulator motor assembly (for driver door).

·

If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

If a power window regulator motor assembly (for driver door) and door window regulator sub-assembly have been removed and installed, or if a power window regulator motor assembly was reused when a door glass or door glass run was replaced, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).



PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DRIVER DOOR WINDOW MOTOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch to on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / D-Door Motor / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


D-Door Motor (Power Window Regulator Motor Assembly (for Driver Door))
Tester Display Test Part Control Range Diagnostic Note
Power Window Power window OFF / UP / DOWN -

OK:

Driver door power window motor operates.




OK

2.PERFORM INITIALIZATION (DRIVER DOOR WINDOW)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

2.PERFORM INITIALIZATION (DRIVER DOOR WINDOW)
a.

Initialize the power window regulator motor assembly (for driver door) (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).



NEXT

3.CHECK POWER WINDOW CONTROL SYSTEM (DRIVER DOOR WINDOW)
3.CHECK POWER WINDOW CONTROL SYSTEM (DRIVER DOOR WINDOW)
a.

Check that the driver door power window operates normally by opening and closing the window (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).

OK:

Driver door power window operates normally.




OK

4.CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

4.CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY
a.

Check that the power window components are installed correctly.

OK:

Power window components are installed correctly.




OK

5.CHECK DTC OUTPUT

NG

INSTALL PARTS CORRECTLY

5.CHECK DTC OUTPUT
a.

Turn the power switch off.


b.

Wait for at least 10 seconds, and then turn the power switch to on (IG).


c.

Check for DTCs (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DTC CHECK / CLEAR).

OK:

B2311 output does not recur.




OK

END

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)