Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW MASTER SWITCH › 2011.12–2017.06
RM2170E _59 Vehicle Exterior _057045 WINDOW / GLASS _0278148 POWER WINDOW MASTER SWITCH G

WINDOW / GLASS  POWER WINDOW MASTER SWITCH  INSPECTION  


PROCEDURE

Hide 84820 1.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for LHD)

B302422E62
1.25,1.688 1.25,0.802 1.25,0.802 0.927,0.802 false 1.417,2.01 1.417,2.896 1.417,2.896 0.896,2.896 false 1.115,2.01 1.115,2.635 1.115,2.635 0.896,2.635 false 1.573,2.01 1.573,3.167 1.573,3.167 0.896,3.167 false 1.573,1.688 1.573,0.406 1.573,0.406 0.896,0.406 false 1.719,1.688 1.719,0.125 1.719,0.125 0.906,0.125 false 2.333,1.656 2.333,0.771 2.333,0.771 2.604,0.771 false 2.333,2.01 2.333,2.646 2.333,2.646 2.604,2.646 false 2.052,2 2.052,2.906 2.052,2.906 2.604,2.906 false 1.875,2 1.875,3.177 1.875,3.177 2.604,3.177 false 1.885,1.688 1.885,0.125 1.885,0.125 2.594,0.125 false 0.719,0.719 0.979,0.885 0.26,0.167 10 false U 0.208,0.177 0.396,0.344 0.188,0.167 10 false *a 0.719,2.771 0.844,2.938 0.125,0.167 10 false U 2.667,2.771 2.792,2.938 0.125,0.167 10 false U 0.719,3.042 0.844,3.208 0.125,0.167 10 false D 2.667,3.042 2.792,3.208 0.125,0.167 10 false D 0.719,2.521 0.844,2.688 0.125,0.167 10 false D 2.667,0.719 2.813,0.885 0.146,0.167 10 false E 2.667,2.521 2.802,2.688 0.135,0.167 10 false U 2.667,0.042 3.135,0.208 0.469,0.167 10 false AUTO 0.719,0.031 0.885,0.198 0.167,0.167 10 false D 0.719,0.333 0.865,0.5 0.146,0.167 10 false B

a.

Check the switch function.

i.

Turn the window lock switch off and operate the switches on the power window regulator master switch assembly.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Driver Side Switch
Tester Connection Switch Condition Specified Condition
4 (AUTO) - 1 (E) AUTO UP Below 1 Ω
8 (U) - 1 (E) AUTO UP Below 1 Ω
8 (U) - 1 (E) MANUAL UP Below 1 Ω
5 (D) - 1 (E) MANUAL DOWN Below 1 Ω
4 (AUTO) - 1 (E) AUTO DOWN Below 1 Ω
5 (D) - 1 (E) AUTO DOWN Below 1 Ω


Standard Resistance:
Front Passenger Side Switch
Tester Connection Switch Condition Specified Condition
6 (B) - 16 (U) UP Below 1 Ω
1 (E) - 15 (D) UP Below 1 Ω
1 (E) - 16 (U) OFF Below 1 Ω
1 (E) - 15 (D) OFF Below 1 Ω
1 (E) - 16 (U) DOWN Below 1 Ω
6 (B) - 15 (D) DOWN Below 1 Ω


Standard Resistance:
Rear RH Side Switch
Tester Connection Switch Condition Specified Condition
6 (B) - 10 (U) UP Below 1 Ω
1 (E) - 18 (D) UP Below 1 Ω
1 (E) - 18 (D) OFF Below 1 Ω
1 (E) - 10 (U) OFF Below 1 Ω
6 (B) - 18 (D) DOWN Below 1 Ω
1 (E) - 10 (U) DOWN Below 1 Ω


Standard Resistance:
Rear LH Side Switch
Tester Connection Switch Condition Specified Condition
6 (B) - 12 (U) UP Below 1 Ω
1 (E) - 13 (D) UP Below 1 Ω
1 (E) - 13 (D) OFF Below 1 Ω
1 (E) - 12 (U) OFF Below 1 Ω
6 (B) - 13 (D) DOWN Below 1 Ω
1 (E) - 12 (U) DOWN Below 1 Ω


Text in Illustration
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)

If the result is not as specified, replace the power window regulator master switch assembly.



b.
B302422E63
1.99,1.677 1.99,0.781 1.99,0.781 1.042,0.781 false 2.344,1.667 2.344,0.781 2.344,0.781 2.615,0.781 false 2.667,0.708 2.833,0.875 0.167,0.167 10 false E 0.635,0.729 1.031,0.896 0.396,0.167 10 false LED+ 0.281,0.292 0.469,0.458 0.188,0.167 10 false *a

Check that the LED illuminates.

i.

Apply auxiliary battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

OK:
Measurement Condition Specified Condition
Auxiliary battery positive (+) → Terminal 3 (LED+)
Auxiliary battery negative (-) → Terminal 1 (E)
LED illuminates


Text in Illustration
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)

If the result is not as specified, replace the power window regulator master switch assembly.



c.
B364773E19
2.5,0.5 2.333,0.5 2.333,0.5 2.323,1.427 false 0.979,0.5 1.229,0.5 1.229,0.5 1.229,1.438 false 2.5,0.25 1.844,0.25 1.844,0.25 1.854,1.427 false 0.979,0.25 1.698,0.25 1.698,0.25 1.698,1.448 false 2.583,0.438 2.896,0.635 0.313,0.198 10 false E 0.833,0.417 1.146,0.615 0.313,0.198 10 false U 2.573,0.177 3.104,0.375 0.531,0.198 10 false AUTO 0.833,0.177 1.146,0.375 0.313,0.198 10 false D

Check the switch function.

i.

Reconnect the power window regulator master switch assembly connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
8 (U) - 1 (E) Ignition switch ON, driver door power window regulator switch off 11 to 14 V
8 (U) - 1 (E) Ignition switch ON, driver door power window regulator switch up (Auto up position) Below 1 V
8 (U) - 1 (E) Ignition switch ON, driver door power window regulator switch up (Manual operation) Below 1 V
4 (AUTO) - 1 (E) Ignition switch ON, driver door power window regulator switch off 11 to 14 V
4 (AUTO) - 1 (E) Ignition switch ON, driver door power window regulator switch up (Auto up position) Below 1 V
4 (AUTO) - 1 (E) Ignition switch ON, driver door power window regulator switch down (Auto down position) Below 1 V
5 (D) - 1 (E) Ignition switch ON, driver door power window regulator switch off 11 to 14 V
5 (D) - 1 (E) Ignition switch ON, driver door power window regulator switch down (Auto down position) Below 1 V
5 (D) - 1 (E) Ignition switch ON, driver door power window regulator switch down (Manual operation) Below 1 V


Text in Illustration
*a Component with harness connected
(Power Window Regulator Master Switch Assembly)

If the result is not as specified, replace the power window regulator master switch assembly.



Hide 84820 2.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for RHD)

B302422E64
1.104,1.656 1.104,0.771 1.104,0.771 0.917,0.771 false 1.417,2 1.417,2.885 1.417,2.885 0.896,2.885 false 1.115,2 1.115,2.625 1.115,2.625 0.896,2.625 false 2.052,1.99 2.052,2.875 2.052,2.875 2.615,2.875 false 2.344,2 2.344,2.625 2.344,2.625 2.615,2.625 false 1.573,1.99 1.573,3.146 1.573,3.146 0.896,3.146 false 1.573,1.656 1.573,0.375 1.573,0.375 0.896,0.375 false 1.719,1.667 1.719,0.104 1.719,0.104 0.938,0.104 false 2.333,1.656 2.333,0.771 2.333,0.771 2.604,0.771 false 1.875,1.979 1.875,3.156 1.875,3.156 2.604,3.156 false 1.885,1.667 1.885,0.104 1.885,0.104 2.594,0.104 false 0.719,0.688 0.865,0.854 0.146,0.167 10 false E 0.208,0.177 0.396,0.344 0.188,0.167 10 false *a 0.719,2.781 0.844,2.948 0.125,0.167 10 false U 2.667,2.781 2.792,2.948 0.125,0.167 10 false U 0.719,3.052 0.844,3.219 0.125,0.167 10 false D 2.667,3.052 2.792,3.219 0.125,0.167 10 false D 2.667,2.531 2.792,2.698 0.125,0.167 10 false D 0.719,2.542 0.844,2.708 0.125,0.167 10 false U 2.667,0.688 2.823,0.854 0.156,0.167 10 false U 2.667,0.031 3.135,0.198 0.469,0.167 10 false AUTO 0.719,0.031 1.188,0.198 0.469,0.167 10 false D 0.719,0.302 0.865,0.469 0.146,0.167 10 false B

a.

Check the switch function.

i.

Turn the window lock switch off and operate the switches on the power window regulator master switch assembly.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Driver Side Switch
Tester Connection Switch Condition Specified Condition
4 (AUTO) - 9 (E) AUTO UP Below 1 Ω
1 (U) - 9 (E) AUTO UP Below 1 Ω
1 (U) - 9 (E) MANUAL UP Below 1 Ω
5 (D) - 9 (E) MANUAL DOWN Below 1 Ω
4 (AUTO) - 9 (E) AUTO DOWN Below 1 Ω
5 (D) - 9 (E) AUTO DOWN Below 1 Ω


Standard Resistance:
Front Passenger Side Switch
Tester Connection Switch Condition Specified Condition
6 (B) - 12 (U) UP Below 1 Ω
9 (E) - 13 (D) UP Below 1 Ω
9 (E) - 12 (U) OFF Below 1 Ω
9 (E) - 13 (D) OFF Below 1 Ω
9 (E) - 12 (U) DOWN Below 1 Ω
6 (B) - 13 (D) DOWN Below 1 Ω


Standard Resistance:
Rear RH Side Switch
Tester Connection Switch Condition Specified Condition
6 (B) - 16 (U) UP Below 1 Ω
9 (E) - 15 (D) UP Below 1 Ω
9 (E) - 15 (D) OFF Below 1 Ω
9 (E) - 16 (U) OFF Below 1 Ω
6 (B) - 15 (D) DOWN Below 1 Ω
9 (E) - 16 (U) DOWN Below 1 Ω


Standard Resistance:
Rear LH Side Switch
Tester Connection Switch Condition Specified Condition
6 (B) - 18 (U) UP Below 1 Ω
9 (E) - 10 (D) UP Below 1 Ω
9 (E) - 10 (D) OFF Below 1 Ω
9 (E) - 18 (U) OFF Below 1 Ω
6 (B) - 10 (D) DOWN Below 1 Ω
9 (E) - 18 (U) DOWN Below 1 Ω


Text in Illustration
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)

If the result is not as specified, replace the power window regulator master switch assembly.



b.
B302422E65
1.104,1.677 1.104,0.781 1.104,0.781 0.823,0.781 false 2.042,1.677 2.042,0.792 2.042,0.792 2.313,0.792 false 0.635,0.729 0.792,0.896 0.156,0.167 10 false E 2.354,0.708 2.771,0.875 0.417,0.167 10 false LED+ 0.281,0.292 0.469,0.458 0.188,0.167 10 false *a

Check that the LED illuminates.

i.

Apply auxiliary battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

OK:
Measurement Condition Specified Condition
Auxiliary battery positive (+) → Terminal 3 (LED+)
Auxiliary battery negative (-) → Terminal 9 (E)
LED illuminates


Text in Illustration
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)

If the result is not as specified, replace the power window regulator master switch assembly.



c.
B364773E20
0.738,0.533 0.936,0.822 0.198,0.288 10 E 2.625,0.624 2.341,0.624 2.341,0.624 2.341,1.46 false 2.664,0.533 3.120,0.750 0.456,0.217 10 U 0.738,0.217 1.078,0.505 0.340,0.288 10 D 0.924,0.624 1.399,0.624 1.399,0.624 1.399,1.434 false 2.664,0.217 3.120,0.434 0.456,0.217 10 AUTO 2.627,0.295 1.875,0.295 1.875,0.295 1.875,1.46 false 0.935,0.295 1.723,0.295 1.723,0.295 1.723,1.46 false

Check the switch function.

i.

Reconnect the power window regulator master switch assembly connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
1 (U) - 9 (E) Ignition switch ON, driver door power window regulator switch off 11 to 14 V
1 (U) - 9 (E) Ignition switch ON, driver door power window regulator switch up (Auto up position) Below 1 V
1 (U) - 9 (E) Ignition switch ON, driver door power window regulator switch up (Manual operation) Below 1 V
4 (AUTO) - 9 (E) Ignition switch ON, driver door power window regulator switch off 11 to 14 V
4 (AUTO) - 9 (E) Ignition switch ON, driver door power window regulator switch up (Auto up position) Below 1 V
4 (AUTO) - 9 (E) Ignition switch ON, driver door power window regulator switch down (Auto down position) Below 1 V
5 (D) - 9 (E) Ignition switch ON, driver door power window regulator switch off 11 to 14 V
5 (D) - 9 (E) Ignition switch ON, driver door power window regulator switch down (Auto down position) Below 1 V
5 (D) - 9 (E) Ignition switch ON, driver door power window regulator switch down (Manual operation) Below 1 V


Text in Illustration
*a Component with harness connected
(Power Window Regulator Master Switch Assembly)

If the result is not as specified, replace the power window regulator master switch assembly.