Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR(for Front Door) › 2011.12–2017.06
RM2170E _59 Vehicle Exterior _057045 WINDOW / GLASS _0278151 POWER WINDOW REGULATOR MOTOR(for Front Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Front Door)  INSPECTION  


PROCEDURE

Hide 85720D 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (w/ Jam Protection Function)

a.
B203475E30
0.133,0.087 0.291,0.227 0.158,0.140 10 *a 1.619,2.129 1.947,2.269 0.328,0.140 10 GND 1.45,2.951 1.910,3.096 0.459,0.144 10 DOWN 0.371,2.951 0.582,3.089 0.211,0.137 10 UP 0.411,2.129 0.523,2.269 0.112,0.140 10 B 1.216,2.527 1.216,2.213 1.216,2.213 1.614,2.213 false 1.09,2.519 1.086,2.212 1.086,2.212 0.54,2.212 false 1.231,2.711 1.231,3.037 1.231,3.037 1.459,3.037 false 1.049,2.711 1.049,3.033 1.049,3.033 0.617,3.033 false 2.96,1.857 3.118,1.997 0.158,0.140 10 *b 2.333,2.33 2.491,2.469 0.158,0.140 10 *c

Apply positive (+) auxiliary battery voltage to connector terminal 2 (B).

NOTICE:

Do not apply positive (+) auxiliary battery voltage to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.



b.

Connect a ground lead to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).


c.

Check that the motor gear rotates smoothly as follows:

OK:
Measurement Condition Specified Condition
1.

Connect a positive (+) auxiliary battery lead to terminal 2 (B), connect a negative (-) auxiliary battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal 10 (UP).

3.

Disconnect and reconnect the negative (-) auxiliary battery lead for terminal 10 (UP) within 1 second.


Motor gear rotates clockwise
1.

Connect the positive (+) auxiliary battery lead to terminal 2 (B), connect a negative (-) auxiliary battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal 7 (DOWN).

3.

Disconnect and reconnect the negative (-) auxiliary battery lead for terminal 7 (DOWN) within 1 second.


Motor gear rotates counterclockwise


Text in Illustration
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Counterclockwise
*c Clockwise

If the result is not as specified, replace the power window regulator motor assembly LH.


NOTICE:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.



Hide 85720D 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (w/o Jam Protection Function)

a.
B127535E04
0.067,0.0010 0.238,0.18 0.171,0.178 10 *a 1.576,0.883 1.75,1.089 0.173,0.206 10 *c 1.252,1.643 1.405,1.845 0.153,0.201 10 *d 0.726,0.265 0.897,0.443 0.171,0.178 10 *b

Apply auxiliary battery voltage to the motor connector according to the table below.

NOTICE:

Do not apply auxiliary battery voltage to any terminals except terminals 1 and 2.


Standard:
Measurement Condition Specified Condition
Auxiliary battery positive (+) → Terminal 2
Auxiliary battery negative (-) → Terminal 1
Motor gear rotates clockwise
Auxiliary battery positive (+) → Terminal 1
Auxiliary battery negative (-) → Terminal 2
Motor gear rotates counterclockwise


Text in Illustration
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Motor Gear
*c Counterclockwise
*d Clockwise

If the result is not as specified, replace the power window regulator motor assembly LH.


Hide 85710E 3.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (w/ Jam Protection Function)

a.
B203474E25
0.058,0.06 0.235,0.214 0.177,0.154 10 *a 2.677,2.93 3.137,3.068 0.460,0.139 10 DOWN 2.849,2.105 3.179,2.243 0.329,0.139 10 GND 1.663,2.105 1.776,2.243 0.112,0.139 10 B 1.564,2.93 1.776,3.068 0.212,0.139 10 UP 2.413,2.5 2.413,2.184 2.413,2.184 2.834,2.184 false 2.298,2.5 2.298,2.184 2.298,2.184 1.781,2.184 false 2.272,2.709 2.272,3.003 2.272,3.003 1.824,3.003 false 2.439,2.701 2.439,2.997 2.439,2.997 2.679,2.997 false 0.299,1.813 0.462,1.967 0.163,0.154 10 *b 0.952,2.242 1.115,2.397 0.163,0.154 10 *c

Apply positive (+) auxiliary battery voltage to connector terminal 2 (B).

NOTICE:

Do not apply positive (+) auxiliary battery voltage to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.



b.

Connect a ground lead to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).


c.

Check that the motor gear rotates smoothly as follows:

OK:
Measurement Condition Specified Condition
1.

Connect the positive (+) auxiliary battery lead to terminal 2 (B), connect a negative (-) auxiliary battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal 10 (UP).

3.

Disconnect and reconnect the negative (-) auxiliary battery lead for terminal 10 (UP) within 1 second.


Motor gear rotates counterclockwise
1.

Connect a positive (+) auxiliary battery lead to terminal 2 (B), connect a negative (-) auxiliary battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal 7 (DOWN).

3.

Disconnect and reconnect the negative (-) auxiliary battery lead for terminal 7 (DOWN) within 1 second.


Motor gear rotates clockwise


Text in Illustration
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Clockwise
*c Counterclockwise

If the result is not as specified, replace the power window regulator motor assembly RH.


NOTICE:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.



Hide 85710E 4.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (w/o Jam Protection Function)

a.
B127536E10
2.595,0.313 2.769,0.479 0.175,0.166 10 *b 2.068,1.551 2.261,1.716 0.193,0.166 10 *d 1.575,0.892 1.731,1.057 0.156,0.166 10 *c 1.033,0.032 1.224,0.198 0.191,0.166 10 *a

Apply auxiliary battery voltage to the motor connector according to the table below.

NOTICE:

Do not apply auxiliary battery voltage to any terminals except terminals 1 and 2.


Standard:
Measurement Condition Specified Condition
Auxiliary battery positive (+) → Terminal 1
Auxiliary battery negative (-) → Terminal 2
Motor gear rotates clockwise
Auxiliary battery positive (+) → Terminal 2
Auxiliary battery negative (-) → Terminal 1
Motor gear rotates counterclockwise


Text in Illustration
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Motor Gear
*c Clockwise
*d Counterclockwise

If the result is not as specified, replace the power window regulator motor assembly RH.