Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS
RM2170E _59 Vehicle Exterior _057045 WINDOW / GLASS _0278156 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  INSTALLATION  


PROCEDURE

Hide 56115A 1.INSTALL NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.
B296191

Install 2 new No. 1 windshield glass stoppers to the vehicle body as shown in the illustration.

NOTICE:

Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.



Hide 56116C 2.INSTALL NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.

Using a brush or sponge, coat the application area of 2 new No. 2 windshield glass stoppers with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.

Install the 2 new No. 2 windshield glass stoppers onto the windshield glass, as shown in the illustration.

B298731E03
0.917,1.177 1.156,1.01 false 1.188,1.417 0.813,1.729 0.813,1.729 0.563,1.313 false 6.198,1.156 5.948,0.979 false 5.917,1.406 6.292,1.719 6.292,1.719 6.542,1.302 false 0.25,1.073 0.375,1.25 0.125,0.177 10 true a 6.24,1.729 6.396,1.927 0.156,0.198 10 true *1 0.75,1.75 0.906,1.948 0.156,0.198 10 true *1 1.229,0.885 1.385,1.083 0.156,0.198 10 false *a 2.417,0.24 2.615,0.438 0.198,0.198 10 false *A 6.771,1.042 6.938,1.24 0.167,0.198 10 true a 5.781,0.854 5.938,1.052 0.156,0.198 10 false *a

Text in Illustration
*A Back Side - -
*1 Ceramic Notch - -
*a Windshield Glass Edge Side - -

Standard Dimension:
Area Dimension
a 7.2 to 8.2 mm (0.283 to 0.323 in.)


NOTICE:

Only 2-piece type windshield glass stoppers are provided as supply parts. Use the 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.



Hide 56117A 3.INSTALL WINDOW GLASS ADHESIVE DAM

a.

Using a brush or sponge, coat the application area of a new window glass adhesive dam with primer G.

B298739E03
3.854,3.125 6.875,4.344 3.021,1.219 4.385,1.792 6.875,3.01 2.49,1.219 4.385,0.479 6.875,1.698 2.49,1.219 1.417,2.198 1.177,2.01 false 2.969,2.198 3.208,2.01 false 6.073,3.594 6.208,3.417 false 0.365,4.427 0.708,4.615 0.344,0.188 10 false : *1 1.802,2.76 1.938,2.917 0.135,0.156 10 false A 1.823,2.063 1.958,2.219 0.135,0.156 10 false A 5.333,2.698 5.469,2.854 0.135,0.156 10 false d 5.094,2.688 5.229,2.844 0.135,0.156 10 false c 5.979,1.385 6.115,1.542 0.135,0.156 10 false a 6.229,1.396 6.365,1.552 0.135,0.156 10 false b 0.188,0.135 0.396,0.354 0.208,0.219 10 false *A 1.354,2.646 1.49,2.802 0.135,0.156 10 false B 0.688,2.51 0.823,2.667 0.135,0.156 10 false B 0.99,1.885 1.177,2.073 0.188,0.188 10 false *a 3.896,3.167 4.156,3.344 0.26,0.177 10 false C-C 4.427,1.833 4.688,2.01 0.26,0.177 10 false B-B 0.99,3.281 1.125,3.438 0.135,0.156 10 false C 0.76,4.198 0.896,4.354 0.135,0.156 10 false C 3.24,1.896 3.427,2.083 0.188,0.188 10 false *a 1.896,0.333 2.083,0.521 0.188,0.188 10 false *2 2.604,0.417 2.792,0.604 0.188,0.188 10 false *2 4.427,0.51 4.688,0.688 0.26,0.177 10 false A-A 5.635,4.083 5.771,4.24 0.135,0.156 10 false e 6.208,3.271 6.396,3.458 0.188,0.188 10 false *b

Text in Illustration
*A Back Side - -
*1 Primer G *2 Ceramic Notch for Dam Cut Alignment
*a Dam Cut Area *b Ceramic Line

Standard Dimension:
Area Dimension
a 5.2 mm (0.205 in.)
b 7.0 mm (0.276 in.)
c 7.0 mm (0.276 in.)
d 5.2 mm (0.205 in.)
e 34.8 mm (1.37 in.)


NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.

Install the window glass adhesive dam onto the windshield glass as shown in the illustration.

B298741E03
4.313,1.823 6.802,3.042 2.49,1.219 4.313,0.51 6.802,1.729 2.49,1.219 3.781,3.156 6.802,4.375 3.021,1.219 1.396,2.531 1.167,2.354 false 2.948,2.521 3.188,2.344 false 6.01,3.573 6.146,3.406 false 1.823,3.083 1.958,3.24 0.135,0.156 10 false A 1.823,2.396 1.958,2.552 0.135,0.156 10 false A 6.146,1.385 6.281,1.542 0.135,0.156 10 false a 5.021,2.719 5.156,2.875 0.135,0.156 10 false b 0.188,0.167 0.396,0.385 0.208,0.219 10 false *A 1.313,2.979 1.448,3.135 0.135,0.156 10 false B 0.646,2.844 0.781,3 0.135,0.156 10 false B 1,2.26 1.188,2.448 0.188,0.188 10 false *a 4.354,1.865 4.615,2.042 0.26,0.177 10 false B-B 0.979,3.594 1.115,3.75 0.135,0.156 10 false C 0.74,4.521 0.875,4.677 0.135,0.156 10 false C 3.188,2.24 3.375,2.427 0.188,0.188 10 false *a 1.792,0.25 1.979,0.438 0.188,0.188 10 false *1 2.708,0.396 2.896,0.583 0.188,0.188 10 false *1 4.354,0.552 4.615,0.729 0.26,0.177 10 false A-A 3.823,3.198 4.083,3.375 0.26,0.177 10 false C-C 5.573,4.052 5.708,4.208 0.135,0.156 10 false c 6.135,3.281 6.323,3.469 0.188,0.188 10 false *b

Text in Illustration
*A Back Side - -
*1 Ceramic Notch for Dam Cut Alignment - -
*a Dam Cut Area *b Ceramic Line

Standard Dimension:
Area Dimension
a 7.0 mm (0.276 in.)
b 7.0 mm (0.276 in.)
c 35.0 mm (1.38 in.)



Hide 56111 4.INSTALL WINDSHIELD GLASS SUB-ASSEMBLY

a.
B296183E02
1.677,0.26 1.417,0.26 1.417,0.26 1.417,0.688 true 1.677,0.552 1.417,0.552 false 1.333,0.719 1.521,0.906 0.188,0.188 10 false *1

Position the windshield glass sub-assembly.

Text in Illustration
*1 Matchmark

i.

Using suction cups, place the windshield glass sub-assembly in the correct position.


ii.

Check that the whole contact surface of the windshield glass sub-assembly rim is perfectly even.


iii.

Align the matchmarks on the windshield glass sub-assembly and vehicle body.

NOTICE:

Check that the windshield glass stoppers are attached to the vehicle body correctly.



iv.

Remove the windshield glass sub-assembly.



b.

Using a brush, coat the installation surface on the vehicle body with primer M.

B308012E03
3.25,0.51 5.115,2.354 1.865,1.844 3.25,2.448 5.115,4.292 1.865,1.844 5.156,0.51 7.021,2.354 1.865,1.844 1.615,1.406 2.885,2.438 1.271,1.031 0.188,1.406 1.458,2.438 1.271,1.031 0.135,4.542 0.313,4.656 0.177,0.115 1.646,0.427 1.802,0.271 false 2,2.104 1.833,2.229 false 0.198,4.656 0.313,4.542 false 0.229,4.656 0.313,4.573 false 0.26,4.656 0.313,4.604 false 0.292,4.656 0.313,4.646 false 0.135,4.625 0.208,4.542 false 0.135,4.656 0.25,4.542 false 0.135,4.552 0.146,4.542 false 0.135,4.583 0.177,4.542 false 0.156,4.656 0.281,4.542 false 1.219,2.573 1.354,2.75 0.135,0.177 10 false A 1.229,3.177 1.365,3.354 0.135,0.177 10 false A 1.156,3.406 1.292,3.583 0.135,0.177 10 false B 0.563,3.198 0.698,3.375 0.135,0.177 10 true B 1.708,3.698 1.844,3.875 0.135,0.177 10 false C 1.771,4.333 1.906,4.51 0.135,0.177 10 false C 3.302,0.563 3.604,0.75 0.302,0.188 10 false A-A 3.302,2.5 3.604,2.688 0.302,0.188 10 false B-B 5.188,0.563 5.49,0.75 0.302,0.188 10 false C-C 0.229,1.448 0.406,1.625 0.177,0.177 10 false *a 1.656,1.448 1.833,1.625 0.177,0.177 10 false *b 1.802,0.135 1.979,0.313 0.177,0.177 10 false *1 1.677,2.167 1.854,2.344 0.177,0.177 10 false *3 0.344,4.521 0.823,4.698 0.479,0.177 10 true : *2 4.188,1.167 4.344,1.333 0.156,0.167 10 false *c 3.979,3.24 4.135,3.406 0.156,0.167 10 false *c 5.448,1.115 5.604,1.281 0.156,0.167 10 false *c 6.792,1.5 6.948,1.667 0.156,0.167 10 false *c

Text in Illustration
*1 Brush *2 Primer M
*3 Adhesive - -
*a CORRECT *b INCORRECT
*c Edge of Curved Surface - -

NOTICE:
·

Do not coat the adhesive with primer M.

·

Do not apply too much primer M.

·

Allow the primer M to dry for 3 minutes or more.

·

Throw away any leftover primer M.



HINT:

If an area other than specified is coated by accident, wipe off the primer M with a clean piece of cloth before it dries.



c.

Using a brush or sponge, coat the application area of adhesive with primer G.

U159243E02
3.708,2.74 5.917,3.927 2.208,1.188 3.708,4.021 5.917,5.208 2.208,1.188 0.958,4.021 3.167,5.208 2.208,1.188 0.958,2.74 3.167,3.927 2.208,1.188 4.021,2.271 3.875,2.448 false 6.74,2.271 6.885,2.458 false 1.656,1.094 1.802,1.271 0.146,0.177 10 false A 1.656,0.156 1.802,0.333 0.146,0.177 10 false A 0.781,0.854 0.927,1.031 0.146,0.177 10 false B 0.865,0.167 1.01,0.344 0.146,0.177 10 false B 0.198,0.875 0.344,1.052 0.146,0.177 10 false C 1.094,1.063 1.24,1.24 0.146,0.177 10 false C 1.031,2.802 1.302,2.958 0.271,0.156 10 false A-A 1.021,4.073 1.292,4.229 0.271,0.156 10 false B-B 3.771,4.073 4.042,4.229 0.271,0.156 10 false D-D 4.792,4.208 4.927,4.385 0.135,0.177 10 false d 3.771,2.792 4.042,2.948 0.271,0.156 10 false C-C 2.656,2.865 2.792,3.042 0.135,0.177 10 false a 4.354,2.875 4.49,3.052 0.135,0.177 10 false c 0.094,0.073 0.396,0.271 0.302,0.198 10 false *A 0.542,5.448 0.781,5.615 0.24,0.167 10 false :*1 0.802,1.51 0.948,1.688 0.146,0.177 10 false D 0.677,2.448 0.823,2.625 0.146,0.177 10 false D 3.771,2.448 3.958,2.646 0.188,0.198 10 false *2 6.813,2.469 7,2.667 0.188,0.198 10 false *2 2.625,4.198 2.76,4.375 0.135,0.177 10 false b

Text in Illustration
*A Back Side - -
*1 Primer G *2 Ceramic Notch

Standard Dimension:
Area Dimension
a 7.0 mm (0.276 in.) or more
b 7.0 mm (0.276 in.) or more
c 7.0 mm (0.276 in.) or more
d 19.0 mm (0.748 in.) or more


NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:
·

Apply primer G onto the ceramic notches.

·

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.




d.

Apply adhesive to the glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.
B214800E30
1.198,0.448 1.74,0.802 false 0.76,1 0.854,1.156 0.094,0.156 10 false a 1.771,0.74 1.958,0.938 0.188,0.198 12 false *1 1.094,0.823 1.188,0.979 0.094,0.156 10 false a 0.594,0.594 0.688,0.75 0.094,0.156 10 false b 1.302,1.427 1.396,1.583 0.094,0.156 10 false b

Cut off the tip of the cartridge nozzle as shown in the illustration.

Text in Illustration
*1 Nozzle

Standard Dimension:
Area Dimension
a 8.0 mm (0.315 in.) or more
b 12.0 mm (0.472 in.) or more


HINT:

After cutting off the tip, use all adhesive within the time described in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour and 40 minutes
5°C (41°F) 8 hours



ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the windshield glass sub-assembly as shown in the illustration.

U159244E02
3.823,4.052 5.979,5.323 2.156,1.271 3.823,2.688 5.979,3.958 2.156,1.271 1.01,4.052 3.167,5.323 2.156,1.271 1.01,2.688 3.167,3.958 2.156,1.271 2.948,2.063 3.104,2.292 false 4.042,2.281 3.896,2.458 false 6.719,2.281 6.865,2.469 false 1.656,1.073 1.802,1.25 0.146,0.177 10 false A 1.646,0.167 1.792,0.344 0.146,0.177 10 false A 0.781,0.844 0.927,1.021 0.146,0.177 10 false B 0.865,0.167 1.01,0.344 0.146,0.177 10 false B 0.198,0.927 0.344,1.104 0.146,0.177 10 false C 1.083,1.073 1.229,1.25 0.146,0.177 10 false C 0.083,0.063 0.385,0.26 0.302,0.198 10 false *A 0.542,5.448 0.781,5.615 0.24,0.167 10 false :*1 0.792,1.531 0.938,1.708 0.146,0.177 10 false D 0.698,2.427 0.844,2.604 0.146,0.177 10 false D 2.563,4.219 2.698,4.396 0.135,0.177 10 false b 4.438,2.813 4.573,2.99 0.135,0.177 10 false c 4.313,4.229 4.448,4.406 0.135,0.177 10 false d 1.083,2.75 1.354,2.906 0.271,0.156 10 false A-A 1.083,4.094 1.354,4.25 0.271,0.156 10 false B-B 3.906,2.74 4.177,2.896 0.271,0.156 10 false C-C 4.781,4.208 4.917,4.385 0.135,0.177 10 false e 3.906,4.104 4.177,4.26 0.271,0.156 10 false D-D 5.052,4.208 5.188,4.385 0.135,0.177 10 false f 3.083,2.302 3.229,2.479 0.146,0.177 10 false *1 3.792,2.448 3.979,2.646 0.188,0.198 10 false *2 6.813,2.469 7,2.667 0.188,0.198 10 false *2 2.563,2.813 2.698,2.99 0.135,0.177 10 false a

Text in Illustration
*A Back Side - -
*1 Adhesive *2 Ceramic Notch

Standard Dimension:
Area Dimension
a 8.0 mm (0.315 in.) or more
b 8.0 mm (0.315 in.) or more
c 8.0 mm (0.315 in.) or more
d 19.0 mm (0.748 in.) or more
e 8.0 mm (0.315 in.) or more
f 8.0 mm (0.315 in.) or more


HINT:

Apply adhesive onto the ceramic notches.




e.
B296183E02
1.677,0.26 1.417,0.26 1.417,0.26 1.417,0.688 true 1.677,0.552 1.417,0.552 false 1.333,0.719 1.521,0.906 0.188,0.188 10 false *1

Install the windshield glass sub-assembly.

Text in Illustration
*1 Matchmark

i.

Using suction cups, position the windshield glass so that the matchmarks are aligned, and press it in gently along the rim.

NOTICE:
·

Check that the windshield glass stoppers are attached to the vehicle body correctly.

·

Check the clearance between the vehicle body and windshield glass sub-assembly.




ii.

Lightly press the front surface of the windshield glass sub-assembly to ensure that the windshield glass is securely fit to the vehicle body.

HINT:

Press the glass with a force of 98 N (10 kgf, 22.0 lbf) or more.



iii.

Using a scraper, remove any excess or protruding adhesive.


iv.

Hold the windshield glass using protective tape until the applied adhesive becomes hard.

NOTICE:

Do not drive the vehicle for the time described in the table below.


Minimum Time:
Temperature Minimum Time prior to Driving Vehicle
35°C (95°F) 1 hour and 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours




Hide 5.INSTALL WINDSHIELD OUTSIDE MOULDING

a.

Using a brush or sponge, coat the application area of a new windshield outside moulding with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.

Using a brush or sponge, coat the application area of a new windshield outside moulding with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



c.
B300468

Apply primer G to the shaded area of the upper side of the windshield outside moulding as shown in the illustration.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



d.
B300428

Install the windshield outside moulding onto the windshield glass.


Hide 6.INSPECT FOR LEAK AND REPAIR

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 7.INSTALL ROOF HEADLINING ASSEMBLY